Engineering topics

Erikson, Rebecca L.

Publications and source records attributed to Erikson, Rebecca L..

4 records

DOE OSTI2022

Mass spectrometric investigations into 3D printed parts to assess radiopurity as ultralow background materials for rare event physics detectors

The mass concentrations of 232 Th and 238 U in several 3D printing filaments and printed polymer parts are reported as measures of their radiopurity. In order to minimize background signals in rare event physics detectors, radiopure polymers are necessary as dielectric and structural materials in their construction. New data are reported for polyvinylidene fluoride (PVDF), polyphenylene sulfide (PPS), and two forms of polyetherimide (PEI, branded ULTEM 1010 and 9085). Data for starting filaments and both simple and complex printed parts are reported. PVDF filaments and simple printed beads, were found to have values of approximately 30 and 50 pg g -1 for 232 Th and 238 U, respectively, while a more complex spring clip part had slightly elevated 232 Th levels of 65 pg g -1 , with 238 U remaining at 50 pg g -1 . PPS filament was found to have concentrations of 270 and 710 pg g -1 for 232 Th and 238 U, respectively, and were not chosen to be printed as those levels were already higher than other material options. ULTEM 1010 filaments and printed complex spring clip parts were found to have concentrations of around 5 and 7 pg g -1 for 232 Th and 238 U, respectively, illustrating no significant contamination from the printing process. ULTEM 9085 filaments were found to have concentrations of around 9 and 5 pg g -1 for 232 Th and 238 U, respectively, while the printed complex spring clip part was found to have slightly elevated concentrations of 25 and 7 pg g -1 for 232 Th and 238 U, respectively. All these results were obtained using a novel dry ashing method in crucibles constructed of ultralow background electroformed copper or, when applicable, microwave assisted wet ashing digestion. Samples and process blanks were spiked with 229 Th and 233 U as internal standards prior to dry/wet ashing and determinations were made by inductively coupled plasma mass spectrometry (ICP-MS). In order to maintain high radiopurity levels, pre-cleaning the filaments before printing and post-cleaning the parts is recommended, although the printing process itself has shown to contribute very minute amounts of radiocontaminants.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2021

Mica filled polyetherketoneketones for material extrusion 3D printing

Polyetherketoneketone (PEKK) has superior physical properties to most available thermoplastics compatible with material extrusion-based 3D printing, including analogs in the polyaryletherketone (PAEK) family. To date, the performance of fused filament fabrication (FFF) compatible PEKK has been detailed primarily as a function of varying the isomer ratios composing the co-polymer structure. The strategy to form blends or composites with PEKK for FFF is attractive for further tailoring of performance in application, yet has received limited attention. Here, we report the integration of three grades of mica platelets into PEKK at 10% and 30% mass loadings to generate an array of filament feedstocks that were then used to print objects with a simple FFF machine. The effects of mica coating chemistry and surface treatment on the compatibility with PEKK and resulting properties are described. Mica fillers at both loadings have only subtle influence on the FFF relevant melt rheological properties inherent to PEKK. Pigment micas at high loadings can lower the melting temperature of PEKK (up to 19 ºC) without shifting its glass transition temperature and inhibit much of the undesirable crystallization occurring during processing with unfilled PEKK. The printed composites were effectively cold crystallized post-printing, affording crystalline fractions up to 90% relative to unfilled PEKK with increased dimensional stabilities. All micas, when used as fillers in low and high relative PEKK crystallinities, significantly increased the tensile modulus (as high as 126% or to 7.31 GPa) of parts in correlation to the loading. Furthermore, the underlying microstructural features of a printed composite were compared to unfilled PEKK by use of a high-resolution helical micro-computed tomography instrument. Practically, pigment micas can confer a wide range of rich colors to 3D-printed PEKK.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Tritium Betavoltaic Powered Sensor Platforms: Power Augmentation with Scintillating Particles

Betavoltaics (BV) are long-life power sources that typically convert beta particle radiation into electricity. Largely, the radioactive decays within the source go unharvested by the device. This work seeks to augment the power generation of BV devices by integration of scintillating particles within the radiative getter to convert beta emission which would otherwise not leave the getter into usable light for power generation. Silica-covered barium fluoride scintillating particles were integrated into a tritiated water getter. Power generation was increased from 100s of nW to µW levels with the addition of 0.2 wt. % particles into the getter. Nanowatt-scale sensor platforms were demonstrated with the µW BV devices and the maximum possible lifetime of such platforms was estimated. As this technique enables higher power density BV devices from conventional Si semiconductors (compared to wider bandgap BVs), the further implementation may lower the barrier-to-deployment of these long-life power/sensor platforms.

42 ENGINEERING↗

DOE OSTI2020

Polymer composites for fused filament fabrication and methods of making the same

Disclosed are compositions of a fused filament fabrication (FFF) composite filament having embedded functional materials in a thermoplastic matrix. Methods of making the composite filaments are also disclosed. In one example, a FFF composite filament incorporates a MOF, in an amount greater than 10% by mass, dispersed in a matrix polymer. One example of a method of synthesizing FFF composite filaments involves mixing a suspension that has a MOF with a matrix polymer solution to yield a polymer-MOF mixture. The mixture is cast and dried into a solid composite material, which is formed a FFF composite filament having the MOF in an amount greater than 10% by mass.

36 MATERIALS SCIENCE↗