Search NASA⌕ Search

Engineering topics

Esposito, M

Publications and source records attributed to Esposito, M.

Negative ions: The overlooked species in thin film growth by pulsed laser deposition

Plasma plume species from a ceramic La{sub 0.4}Ca{sub 0.6}MnO{sub 3} target were studied by plasma mass spectrometry as a function of laser fluence, background gas, and deposition pressure to understand the interplay between plasma composition and oxide thin film growth by pulsed laser deposition. The plume composition reveals a significant contribution of up to 24% of negative ions, most notably using a N{sub 2}O background. The significance of negative ions for thin film growth is shown for La{sub 0.4}Ca{sub 0.6}MnO{sub 3} films grown in different background conditions where the best structural properties coincide with the largest amount of negative plasma species.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Super-B Project Accelerator Status

The SuperB project is an international effort aiming at building in Italy a very high luminosity e{sup +}e{sup -} (10{sup 36} cm{sup -2} sec{sup -1}) asymmetric collider at the Y(4S) energy in the CM. The accelerator design has been extensively studied and changed during the past year. The present design, based on the new collision scheme, with large Piwinski angle and the use of 'crab waist' sextupoles already successfully tested at the DA{Phi}NE {Phi}-Factory at LNF Frascati, provides larger flexibility, better dynamic aperture and spin manipulation sections in the Low Energy Ring (LER) for longitudinal polarization of the electron beam at the Interaction Point (IP). The Interaction Region (IR) has been further optimized in terms of apertures and reduced backgrounds in the detector. The injector complex design has been also updated. A summary of the project status will be presented in this paper. The SuperB collider can reach a peak luminosity of 10{sup 36} cm{sup -2} sec{sup -1} with beam currents and bunch lengths similar to those of the past and present e{sup +}e{sup -} Factories, through the use of smaller emittances and new scheme of crossing angle collision. The beams are stored in two rings at 6.7 GeV (HER) and 4.2 GeV (LER). Unique features of the project are the polarization of the electron beam in the LER and the possibility to decrease the energies for running at the {tau}/charm threshold. The option to reuse the PEP-II B-Factory (SLAC) hardware will allow reducing costs. The SuperB facility will require a big complex of civil infrastructure. The main construction, which will house the final part of the LINAC, the injection lines, the damping rings, and the storage rings, will be mainly underground. Two sites have been considered: the campus of Tor Vergata University near Frascati, and the INFN Frascati Laboratory. No decision has been made yet. A footprint of the possible SuperB layout on the LNF area is shown in Fig. 1.

43 PARTICLE ACCELERATORS↗

Vibration Budget for SuperB

We present a vibration budget for the SuperB accelerator. We include ground motion data, motion sensitivity of machine components, and beam feedback system requirements. The SuperB accelerator design attains at least 50 times higher than current B-factories due to smaller beam sizes and a crabbed waist crossing angle scheme at the IP (interaction point). The beam size (1{sigma}) at the IP will be about 10 {micro}m (horizontal) by 40 nm (vertical). These small beam sizes will make the luminosity very sensitive to mechanical vibration and electrical noise. Relative vertical misalignment of the two beams at the IP by only 8 nm will result in a 1% reduction in luminosity. The corresponding horizontal alignment tolerance of is 250x looser (2 {micro}m). The vertical beam angle at the IP for a 1% luminosity loss is fairly loose at 200 {micro}rad, and the horizontal beam angle tolerance is looser still. We will focus on vertical beam position at the IP, since this presents the greatest alignment challenge. The values presented here are for a closed orbit with tunes near a half-integer in the SuperB v.12 lattice.

43 PARTICLE ACCELERATORS↗

The origin of oxygen in oxide thin films: Role of the substrate

During the growth of oxide thin films by pulsed laser deposition, a strong oxygen substrate-to-film transfer has been experimentally observed for SrTiO{sub 3} and LaAlO{sub 3} thin films epitaxially grown on {sup 18}O exchanged SrTiO{sub 3} and LaAlO{sub 3} substrates by secondary ion mass spectrometry depth profiling. This oxygen transfer effect can seriously change the respective thin film properties. Taking the oxygen substrate contribution to the overall oxygen balance into account, original ways to design material properties of oxide thin films can be envisioned like a controlled charge carrier doping of SrTiO{sub 3} thin films.

36 MATERIALS SCIENCE↗