Search NASA⌕ Search

Engineering topics

Esteves, Giovanni

Publications and source records attributed to Esteves, Giovanni.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Increased thermal conductivity and decreased electron–phonon coupling factor of the aluminum scandium intermetallic phase (Al 3 Sc) compared to solid solutions

Aluminum scandium alloys and their intermetallic phases have arisen as potential candidates for the next generation of electrical interconnects. Here, in this work, we measure the in-plane thermal conductivity and electron–phonon coupling factor of aluminum scandium alloy thin films deposited at different temperatures, where the temperature is used to control the grain size and volume fraction of the Al 3 Sc intermetallic phase. As the Al 3 Sc intermetallic formation increases with higher deposition temperature, we measure increasing in-plane thermal conductivity and a decrease in the electron–phonon coupling factor, which corresponds to an increase in grain size. Our findings demonstrate the role that chemical ordering from the formation of the intermetallic phase has on thermal transport.

Chemical elements↗
DOE OSTI2024

Nonvolatile memory cells from hafnium zirconium oxide ferroelectric tunnel junctions using Nb and NbN electrodes

Ferroelectric tunnel junctions (FTJs) utilizing hafnium zirconium oxide (HZO) have attracted interest as non-volatile memory for microelectronics due to ease of integration into back-end-of-line (BEOL) complementary metal oxide semiconductor fabrication. This work examines asymmetric electrode NbN/HZO/Nb devices with 7 nm thick HZO as FTJs in a memory structure, with an output resistance that can be controlled by read and write voltages. The individual FTJs are measured to have a tunneling electroresistance of 10 during the read state without significant filament conduction formation and reasonable ferroelectric performance. Endurance and remanent polarizations of up to 10 5 cycles and 20 μC/cm 2 , respectively, are measured and are shown to be dependent on the cycling voltage. Electrical measurements demonstrate how magnitude of the write pulse can modulate the high state resistance and the read pulse influences both resistance values as well as separation of resistance states. Then, by using two opposite switching FTJ devices in series, a programmable nonvolatile resistor divider is demonstrated. Measurements of these two FTJ unit memory cells show wide applicability to a BEOL microfabrication process for a re-readable, rewritable, and nonvolatile memory cell.

42 ENGINEERING↗
DOE OSTI2024

Perspectives and progress on wurtzite ferroelectrics: Synthesis, characterization, theory, and device applications

Wurtzite ferroelectrics are an emerging material class that expands the functionality and application space of wide bandgap semiconductors. Promising physical properties of binary wurtzite semiconductors include a large, reorientable spontaneous polarization, direct band gaps that span from the infrared to ultraviolet, large thermal conductivities and acoustic wave velocities, high mobility electron and hole channels, and low optical losses. The ability to reverse the polarization in ternary wurtzite semiconductors at room temperature enables memory and analog type functionality and quasi-phase matching in optical devices and boosts the ecosystem of wurtzite semiconductors, provided the appropriate combination of properties can be achieved for any given application. In this article, advances in the design, synthesis, and characterization of wurtzite ferroelectric materials and devices are discussed. Highlights include: the direct and quantitative observation of polarization reversal of ~135 μC/cm 2 charge in Al 1-x B x N via electron microscopy, Al 1-x B x N ferroelectric domain patterns poled down to 400 nm in width via scanning probe microscopy, and full polarization retention after over 1000 h of 200 °C baking and a 2× enhancement relative to ZnO in the nonlinear optical response of Zn 1-x Mg x O. In conclusion, the main tradeoffs, challenges, and opportunities in thin film deposition, heterostructure design and characterization, and device fabrication are overviewed.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Sub-quarter micrometer periodically poled Al 0.68 Sc 0.32 N for ultra-wideband photonics and acoustic devices

In this study, we demonstrate the ability of polarity inversion of sputtered aluminum scandium nitride thin films through post-fabrication processes with domain widths as small as 220 nm at a periodicity of 440 nm. An approach using photo- and electron-beam lithography to generate sub-quarter micrometer feature size with adjustable duty cycle through a lift-off process is presented. Here, the film with a coercive field $E_c^+$ of 5.35 MV/cm was exercised first with a 1 kHz triangular double bipolar wave and ultimately poled with a 0.5 kHz double monopolar wave using a Radiant Precision Premier II tester. The metal polar (M-polar) and nitrogen polar (N-polar) domains were identified and characterized through potassium hydroxide wet etching as well as piezoresponse force microscopy (PFM). Well-distinguished boundaries between the oppositely polarized domain regions were confirmed through the phase diagram of the PFM results. The relationship between the electrode width, poling voltage, and domain growth was experimentally studied and statistically analyzed, where 7.96 nm/V domain width broadening vs escalating poling voltage was observed. This method produces extremely high domain spatial resolution in III-nitride materials via poling and is transferable to a CMOS-compatible photolithography process. The spatial resolution of the periodically poled Al 0.68 Sc 0.32 N is suitable for second-harmonic generation of deep ultraviolet through quasi-phase-matching and RF MEMS operating in the X-Band spectrum.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Impacts to FeRAM design arising from interfacial dielectric layers and wake up modulation in ferroelectric hafnium zirconium oxide

As ferroelectric hafnium zirconium oxide (HZO) becomes more widely utilized in ferroelectric microelectronics, integration impacts of intentional and non-intentional dielectric interfaces and their effects upon the ferroelectric film wake up and circuit parameters become important to understand. In this work, the effect of the addition of a linear dielectric aluminum oxide, Al 2 O 3 , below a ferroelectric Hf 0.58 Zr 0.42 O 2 film in a capacitor structure for FeRAM applications with NbN electrodes was measured. Depolarization fields resulting from the linear dielectric is observed to induce a reduction of the remanent polarization of the ferroelectric. Addition of the aluminum oxide also impacts the wake up of the HZO with respect to the cycling voltage applied. Intricately linked to the design of a FeRAM 1C/1T cell, the metal-ferroelectric-insulator-metal (MFIM) devices are observed to significantly shift charge related to the read states based on aluminum oxide thickness and wake up cycling voltage. As a result, a 33% reduction in the separation of read states is measured, which complicates how a memory cell is designed and illustrates the importance of clean interfaces in devices.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Ferroelectric behavior of sputter deposited Al 0.72 Sc 0.28 N approaching 5 nm thickness

Ferroelectric Al 1-x Sc x N has raised much interest in recent years due to its unique ferroelectric properties and complementary metal oxide semiconductor back-end-of-line compatible processing temperatures. Potential applications in embedded nonvolatile memory, however, require ferroelectric materials to switch at relatively low voltages. One approach to achieving a lower switching voltage is to significantly reduce the Al 1-x Sc x N thickness. In this work, ferroelectric behavior in 5-27 nm films of sputter deposited Al 0.72 Sc 0.28 N has been studied. We find that the 10 kHz normalized coercive field increases from 4.4 to 7.3 MV/cm when reducing the film thickness from 27.1 to 5.4 nm, while over the same thickness range, the characteristic breakdown field of a 12.5 μm radius capacitor increases from 8.3 to 12.1 MV/cm. In conclusion, the 5.4 nm film demonstrates ferroelectric switching at 5.5 V when excited with a 500 ns pulse and a switching speed of 60 ns.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Vertical Etching of Scandium Aluminum Nitride Thin Films Using TMAH Solution

A wide bandgap, an enhanced piezoelectric coefficient, and low dielectric permittivity are some of the outstanding properties that have made Sc x Al 1-x N a promising material in numerous MEMS and optoelectronics applications. One of the substantial challenges of fabricating Sc x Al 1-x N devices is its difficulty in etching, specifically with higher scandium concentration. In this work, we have developed an experimental approach with high temperature annealing followed by a wet etching process using tetramethyl ammonium hydroxide (TMAH), which maintains etching uniformity across various Sc compositions. The experimental results of etching approximately 730 nm of Sc x Al 1-x N (x = 0.125, 0.20, 0.40) thin films show that the etch rate decreases with increasing scandium content. Nevertheless, sidewall verticality of 85°~90° (±0.2°) was maintained for all Sc compositions. Based on these experimental outcomes, it is anticipated that this etching procedure will be advantageous in the fabrication of acoustic, photonic, and piezoelectric devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Metal stack templates for suppressing secondary grains in sca1n

A metal stack for templating the growth of AlN and ScAlN films is disclosed. The metal stack comprises one, two, or three layers of metal, each of which is compatible with CMOS post-processing. The metal stack provides a template that promotes the growth of highly textured c-axis {002} AlN and ScAlN films. The metal stacks include one or more metal layers with each metal layer having either a hexagonal {002} orientation or a cubic {111} orientation. If the metal stack includes two or more metal layers, the layers can alternate between hexagonal {002} and cubic {111} orientations. The use of ScAlN results in a higher piezoelectric constant compared to that of AlN for ScAlN alloys up to approximately 44% Sc. The disclosed metal stacks resulted in ScAlN films having XRD FWHM values of less than approximately 1.1° while significantly reducing the formation of secondary grains in the ScAlN films.

Esteves, Giovanni↗