Search NASA⌕ Search

Engineering topics

Ethiraj Venkatapathy

Publications and source records attributed to Ethiraj Venkatapathy.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Ablative TPS Sustainment to Enable NASA's Future Robotic Missions

Since 1960s NASA’s missions have spanned the entire solar system, from Apollo to Jupiter entry ~50 km/s. Ablative TPS has been critical to the success. NASA’s missions will continue to be innovative, one-of-a kind and at the same time, competed mission selection process requires technology readiness to be high to ensure cost and risks are better understood. If missions require new TPS technology, it takes a decade and significant resources to develop them. Competitive proposal tend to use existing ablative TPS. Sustainability of ablative TPS is then essential. This talk will focus on approaches to address the future challenges.

Ethiraj Venkatapathy↗
NASA NTRSDate not supplied

Enabling New and Innovative Low Cost Mars Science Missions with the Adaptable, Deployable, Entry and Placement Technology (ADEPT)

The Adaptive Deployable Entry and Placement Technology (ADEPT) offers a delivery capability for Small Sat or CubeSat orbiter(s), in-situ elements, or landers. ADEPT can deliver the same science payload to a destination with a stowed diameter a factor of 3-4 times smaller than an equivalent rigid aeroshell, alleviating volumetric constraints on the secondary payload accommodation or primary carrier spacecraft bus. The ADEPT system can support payload over a range of mass and geometries to offer a delivery capability for a single or constellation of spacecraft supporting the goals and objectives of “Low Cost Mars Science Missions.”

ADEPT↗
NASA NTRSDate not supplied

NASA Efforts to Explore Additively Manufactured Thermal Protection Systems

Development of the thermal protection system (TPS) needed to protect external and internal surfaces during launch, ascent, cruise, and reentry, is a very specialized field with expertise developed over seven decades and has enabled successful robotic as well as human exploration. Well known examples are: 1) the ablative heatshield that protected Apollo Astronauts during reentry in 1960’s, 2) reusable TPS used on the Space Shuttle Orbiter, which is now sought after by commercial space industry, and 3) hot structures, such as Carbon-Carbon and other high temperature materials needed to operate control surfaces and sharp leading edges during hypervelocity flight. TPS function demands fail-safe design to ensure mission success. One TPS does not fit all, and each application requires a unique material along with manufacturing and integration approach. TPS mass is a key metric. A robust but inefficient TPS reduces payload mass. Mission- and domain-unique TPS development and flight certification efforts have been expensive with long lead times. As a result, there are limited TPS choices with high cost. For future commercial efforts to be successful, the ability to rapidly develop TPS, based on specific needs and at a lower cost, without compromising either mass efficiency or functionality is necessary. NASA is looking into this. Additive manufacturing (AM) techniques have shown their utility in making complex parts and, through automation, the potential to reduce cost and schedule in some applications. The promise of additive manufacturing to TPS, while exciting, is unexplored. In the past several years, NASA has made exploratory investments in internal development as well as in small business and universities through SBIR and STTR programs. In addition, NASA is bringing together the TPS as well as Additive Manufacturing communities to explore approaches to prioritize focus areas for broad benefits. The very first “Additively Manufactured Thermal Protection System Workshop,” to be held at NASA Johnson Space Center in Houston at the end of March of this year, is the culmination of a year-long effort to engage the research, development, and user communities involved in both TPS as well as additive manufacturing. The workshop participants include representatives from large and small commercial space industry, DoD, Federally Funded Research and Development Centers, University Researchers and NASA personnel. The proposed talk will highlight future TPS needs of both emerging commercial and Government interests, NASA’s development efforts in additively manufactured TPS, and the findings and recommendations from the first AM TPS Workshop.

Ethiraj Venkatapathy↗
NASA NTRSDate not supplied

Qualification of Domestic Lyocell Based Phenolic Impregnated Carbon Ablator (PICA-D) for NASA Missions

Phenolic Impregnated Carbon Ablator (PICA) is a low-density ablator that has been used as the planetary entry heatshield for several NASA missions since the late 90’s. Its low density and efficient performance characteristics have proven effective for use from Discovery to Flag-ship class missions, from Sample Return missions such as Stardust, OSIRIS-REx to large Mars Lander missions such as Mars Science Lab (MSL) and Mars 2020. The rayon-based carbon precursor raw material used in PICA preform manufacturing has experienced multiple supply chain issues. The challenge involved in finding a replacement fiber source is in processing as well as in the final performance of the ablator. Each replacement necessitates the requalification of the PICA. This has happened at least twice in the past 25 years, and a third substitution is now needed. Due to the obsolescence of the input foreign rayon fiber source, a new variant of PICA has been developed using a domestic rayon-like fiber source, Lyocell. Due to its flight heritage and proven capability, PICA is baselined as the Thermal Protection System (TPS) for Dragonfly and Mars Sample Return Sample Retrieval Lander mission and is being considered for the backshell of the Mars Sample Return Earth Entry System. All three missions are due to be launched between 2026 and 2028. The challenge this time is to ensure the PICA made with domestic material is a suitable replacement to the heritage PICA used in MSL and Mars 2020 so that the design of the heatshield can be matured without much risk. Results are presented from the recent efforts of 22 PICA-D billets that were Lot Acceptance Tested. Thermal, mechanical, and representative environment arc-jet tests have been conducted. Testing of PICA-Domestic (PICA-D) indicates very comparable performance with respect to “heritage” PICA materials and thus PICA-D is expected to be a sustainable and nearly a “drop-in” replacement solution for future NASA missions.

Matt Gasch↗
NASA NTRSDate not supplied

Qualification of Domestic Lyocell Based Phenolic Impregnated Carbon Ablator (PICA-D) for NASA Missions

Phenolic Impregnated Carbon Ablator (PICA) is a low-density ablator that has been used as the planetary entry heatshield for several NASA missions since the late 90’s. Its low density and efficient performance characteristics have proven effective for use from Discovery to Flag-ship class missions, from Sample Return missions such as Stardust, OSIRIS-REx to large Mars Lander missions such as Mars Science Lab (MSL) and Mars 2020. The rayon-based carbon precursor raw material used in PICA preform manufacturing has experienced multiple supply chain issues. The challenge involved in finding a replacement fiber source is in processing as well as in the final performance of the ablator. Each replacement necessitates the requalification of the PICA. This has happened at least twice in the past 25 years, and a third substitution is now needed. Due to the obsolescence of the input foreign rayon fiber source, a new variant of PICA has been developed using a domestic rayon-like fiber source, Lyocell. Due to its flight heritage and proven capability, PICA is baselined as the Thermal Protection System (TPS) for Dragonfly and Mars Sample Return Sample Retrieval Lander mission and is being considered for the backshell of the Mars Sample Return Earth Entry System. All three missions are due to be launched between 2026 and 2028. The challenge this time is to ensure the PICA made with domestic material is a suitable replacement to the heritage PICA used in MSL and Mars 2020 so that the design of the heatshield can be matured without much risk. Results are presented from the recent efforts of 22 PICA-D billets that were Lot Acceptance Tested. Thermal, mechanical, and representative environment arc-jet tests have been conducted. Testing of PICA-Domestic (PICA-D) indicates very comparable performance with respect to “heritage” PICA materials and thus PICA-D is expected to be a sustainable and nearly a “drop-in” replacement solution for future NASA missions.

PICA↗
NASA NTRSDate not supplied

A TPS Design Analysis of Entry Probe Delivery from Orbit for Ice Giant Missions

Previous investigation of direct delivery of a probe into Neptune’s atmosphere showed said approach to be challenging due to high stagnation pressures and heat loads. Entering at a high entry flight path angle (EFPA) results in stagnation pressure beyond current Heatshield for Extreme Entry Environment Technology (HEEET) qualification, while entering at a lower EFPA results in higher heat loads, leading to required HEEET thicknesses beyond manufacturing capabilities. Aerocapture is an enticing alternative entry scenario because it enables a fast trip and the placement of a payload in orbit around Neptune that can also reach Triton. Here, we investigate entry conditions associated with delivering a probe from orbit to assess feasibility. We consider whether 1) this entry scenario results in reasonable conditions, and 2) HEEET single insulating layer (mid-density carbon phenolic, 3MDCP) can be used to decrease mass, risk, and cost.

Hannah S. Alpert↗
NASA NTRSDate not supplied

Development of Additive Manufacturing Technologies for 3D Printing of Spacecraft Heat Shields

Introduction: Ablative heat shields are an enabling technology for entry into planetary atmospheres. From the PICA heatshields used for several Mars rovers to the carbon phenolic material used for Galileo’s Jupiter entry probe, the heat shield manages the heat load transferred to the payload, protecting the sensitive scientific instruments carried on entry probes. The Additive Manufacturing of Thermal Protection Systems (AMTPS) project, an Early Career Initiative (ECI) funded by NASA’s Space Technology Mission Directorate and led by NASA Johnson Space Center, seeks to develop materials and processes for 3D printing ablative heat shields for spacecraft. Current methods for producing ablative heat shields are extremely labor intensive and re-quire extensive hands-on processes and quality control characterization. Additive manufacturing (AM) offers the possibility of reduced production times, improved reliability, and enhanced performance via graded compositions. Costs will also be reduced by reducing the time and labor required for heat shield production. Direct integration of the heat shield onto the structure during processing simplifies integration and reduces risk. Material Development: A critical challenge for the project is development of a material system that can (1) be printed in a near-net shape process and (2) perform well as an ablator. Achieving printability requires the material to flow under applied pressure, but maintain its shape once extruded from the printer nozzle. Ablative performance is measured by a multitude of markers, including char yield, char strength, thermal conductivity, and recession rate. Furthermore, there are several mechanical and thermal property considerations for vehicle integration including coefficient of thermal expansion (CTE) and residual stress. AM technology will be leveraged to grade the material formulation and properties through the thickness of the heat shield, an architecture not possible with current manufacturing processes. To this end, “robust” material formulations have been pre-pared with higher density for use on the surface where most ablation will occur. “Insulative” material formulations, with lower density and lower thermal conductivity, are prepared for use in the depth of the heat shield. This graded architecture will re-duce the overall mass of the heat shield and reduce costs and/or increase scientific payload capacities. To achieve a material system with the required properties, multiple resins have been investigated in collaboration with NASA Ames Research Center. To tune printability and performance, resin additives were studied to improve flexibility of the cured material while maintaining acceptable ablative performance. Material coupons were printed and studied via a suite of mechanical and thermal characterization methods. Arc jet testing was conducted at NASA Ames Research Center to evaluate ablative performance and thermal protection under conditions expected in atmospheric entry. Manufacturing Scale-Up: A partnership with Oak Ridge National Laboratory (ORNL) aims to enable full-scale fabrication of a 3D printed heat shield. Leveraging expertise in manufacturing and 3D printing at ORNL, a mid-scale manufacturing demonstration unit will be built and tested, using a dual-layer ablative system printed directly onto the titanium structure. Work on robotic system integration is ongoing and efforts to scale up material mixing with a material compound will ensure accurate and homogenous composition. Flight Test: A hypersonic sub-orbital flight test will provide a rigorous test of material performance ranging from ablation, thermal management, and mechanical integrity. Design of the capsule has taken place in collaboration with the University of Kentucky. Data collected from the flight will inform future design efforts in material formulation, printing methodology, and heat shield-capsule integration.

additive manufacturing↗