Engineering topics

Etsion, I.

Publications and source records attributed to Etsion, I..

At least 19 records

NASA NTRS1985

Analysis of an oscillatory oil squeeze film containing a central gas bubble

A squeeze-film damper, consisting of two circular plates, having only normal oscillatory relative motion is considered. The liquid lubricant between the plates is assumed to contain a single central gas bubble. The effect of the bubble on the damper performance is analyzed. Comparison is made with the performance of a pure liquid damper. Substantial deviations in peak dynamic pressures are predicted which explain discrepancies between experimental and theoretical results reported in the literature.

Haber, S.↗

NASA NTRS1982

Performance of the coned-face end seal with regard to energy conservation

The effects of face coning on seal performance are evaluated with particular regard to the energy saving potential of convex conedface end seals as indicated by torque reduction. Experiments were conducted using a conventional carbon flat-face pusher-type seal, a coned-face pusher-type seal, coned-face bellows-type seal, and a modified coned-face pusher-type seal intended for dynamically unstable operation, with shaft rotation at up to 8000 rpm, pressures of up to 2758 kPa, and a petroleum-based turbine oil as lubricant. Torque at the seal interface is found to be reduced by 42% when the standard flat-face seal is replaced by a coned seal, although the leakage of the cone-face seal was 11 times greater. Reduction of seal balance from 76.1 to 51.3% resulted in an additional 44% reduction in torque, although at the expense of excessive leakage, but did not produce unstable operation. Face temperatures were reduced by 33-56 C and wear was also reduced greatly on the cone face seals. Seal performance is noted to be in agreement with analytical calculations.

Sehnal, J.↗

NASA NTRS1982

Energy efficient face seal

Torque, face temperature, leakage, and wear of a flat face seal were compared with three coned face seals at pressures up to 2758 kPa and speeds up to 8000 rpm. Axial movement of the mating seal parts was recorded by a digital data acquisition system. The coning of the tungsten carbide primary ring ranged from .51 micro-m to 5.6 micro-m. The torque of the coned face seal balanced to 76.3% was an average 42% lower, the leakage eleven times higher, than that of the standard flat face seal. The reduction of the balance of the coned face seal to 51.3% resulted by decreasing the torque by an additional 44% and increasing leakage 12 to 230 times, depending on the seal shaft speed. No measurable wear was observed on the face of the coned seals.

Sehnal, J.↗

NASA NTRS1981

Observation of pressure variation in the cavitation region of submerged journal bearings

Visual observations and pressure measurements in the cavitation zone of a submerged journal bearing are described. Tests are run at speeds of 1840 and 3000 rpm, and at each speed, four different levels of the ambient supply pressure are applied, ranging from 13.6 KPa to 54.4 KPa. A strong reverse flow is detected inside the cavitation area adjacent to its downstream end, and significant pressure variations on the order of 50 KPa are found inside the cavitation region at the downstream portion of its circumferential extent. Results indicate that the assumption of a constant cavitation pressure is incorrect in the case of enclosed cavitations, and it is postulated that oil which is saturated with air under atmospheric pressure becomes oversaturated in the subcavity pressure loop.

Etsion, I.↗

NASA NTRS1981

Modified face seal for positive film stiffness

The film stiffness of a face seal is improved without increasing the sealing and dam area by using an apparatus which includes a primary seal ring in the form of a nose piece. A spring forces a sealing surface on the seal ring into sealing contact with a seat to form a face seal. A circumferential clearance seal is formed in series with this face seal by a lip on the piece. The width of the surface of the lip is substantially the same as the width of the sealing surface on the face seal and the clearance between the surface on the lip and the shaft is substantially the same as the spacing between the face sealing surfaces on the face seal when the shaft is rotating. The circumferential clearance seal restricts the flow of fluid from a main cavity to an intermediate cavity with a resulting pressure drop. The hydrostatic opening face is strongly dependent on the face seal clearance, and the desired axial stiffness is achieved.

Etsion, I.↗

NASA NTRS1981

Simulation and visualization of face seal motion stability by means of computer generated movies

A computer aided design method for mechanical face seals is described. Based on computer simulation, the actual motion of the flexibly mounted element of the seal can be visualized. This is achieved by solving the equations of motion of this element, calculating the displacements in its various degrees of freedom vs. time, and displaying the transient behavior in the form of a motion picture. Incorporating such a method in the design phase allows one to detect instabilities and to correct undesirable behavior of the seal. A theoretical background is presented. Details of the motion display technique are described, and the usefulness of the method is demonstrated by an example of a noncontacting conical face seal.

Etsion, I.↗

NASA NTRS1981

Self-stabilizing radial face seal

A self-stabilizing radial face seal comprises an axial member and a primary seal ring juxtapositioned to a seal seat. At least one primary seal ring and seal seat unit is affixed to the axial member so as to rotate with it. The primary seal ring has a front face which opposes a face of the seal seat. The seal has both high-pressure and low-pressure regions of fluid, and seal seat is provided with a porous ring-like circumferential structure in the face of the seal seat opposite the front face of the primary seal ring.

Etsion, I.↗

NASA NTRS1980

Computer program documentation for the dynamic analysis of a noncontacting mechanical face seal

A computer program is presented which achieves a numerical solution for the equations of motion of a noncontacting mechanical face seal. The flexibly-mounted primary seal ring motion is expressed by a set of second order differential equations for three degrees of freedom. These equations are reduced to a set of first order equations and the GEAR software package is used to solve the set of first order equations. Program input includes seal design parameters and seal operating conditions. Output from the program includes velocities and displacements of the seal ring about the axis of an inertial reference system. One example problem is described.

Auer, B. M.↗

NASA NTRS1980

Dynamic analysis of noncontacting face seals

The dynamic behavior of a noncontacting coned face seal is analyzed taking into account various design parameters and operating conditions. The primary seal ring motion is expressed by a set of nonlinear equations for three degrees of freedom. These equations, which are solved numerically, allow identification of two dimensionless groups of parameters that affect the seal dynamic behavior. Stability maps for various seals are presented. These maps contain a stable-to-unstable transition region in which the ring wobbles at half the shaft frequency. The effect of various parameters on seal stability is discussed and an empirical expression for critical stability is offered.

Etsion, I.↗

NASA NTRS1980

Dynamic response to rotating-seat runout in non-contacting face seals

The dynamic response of a flexibly mounted ring to runout of the rotating seat in mechanical face seals is analyzed assuming small perturbations. It is found that tracking ability of the stator depends only on its dynamic characteristics and operating conditions and is not affected by the amount of runout. Three different modes of dynamic response are shown and the condition for parallel tracking is presented.

Etsion, I.↗

NASA NTRS1980

Analysis and design of a uniform-clearance, pumping-ring rod seal for the Stirling engine

A uniform clearance pumping ring, as opposed to the conventional taper clearance one, is described. The uniform clearance concept eliminates complex elastohydrodynamic problems and enables a simple analytical treatment to be made. An analytical expression is derived for the pumping rate showing the effect of various design parameters on the pumping ring's performance. An optimum clearance is found by which the pumping rate is maximized and a numerical example is presented to demonstrate the potential of the uniform clearance design.

Etsion, I.↗

NASA NTRS1980

Simulation and visualization of face seal motion stability by means of computer generated movies

Etsion, I.↗

NASA NTRS1980

Observation of pressure variation in the cavitation region of submerged journal bearings

Visual observations and pressure measurements in the cavitation zone of a submerged journal bearing are described. Tests were performed at various shaft speeds and ambient pressure levels. Some photographs of the cavitation region are presented showing strong reverse flow at the downstream end of the region. Pressure profiles are presented showing significant pressure variations inside the cavitation zone, contrary to common assumptions of constant cavitation pressure.

Etsion, I.↗

NASA NTRS1979

Observation of self-excited wobble in face seals

A face seal model consisting of a rigidly mounted rotor and a flexibly mounted stator was tested under conditions of eccentric loading. Self-excited oscillations in the form of combined precession and nutation of the stator were observed. The nature of the motion and its frequency are dependent on rotational speed, seal clearance, and external tilting moment. It is possible that some unexplained seal failures and waviness of seal faces are the result of such self excited wobble.

Etsion, I.↗

NASA NTRS1979

Performance of end-face seals with diametral tilt and coning - Hydrodynamic effects

Hydrodynamic effects in end-face seals with diametral tilt and coning are analyzed. A closed-form solution for the axial separating force and the restoring and transverse moments is presented that covers the whole range from zero to full angular misalignment at various degrees of coning. Both low-pressure seals with cavitating flow and high-pressure seals with full fluid film are considered. The effect of coning is to reduce the axial force and the restoring and transverse moments compared to their magnitude in flat-face seals. Strong coupling between diametral tilt and transverse moment is demonstrated. This transverse moment which is entirely due to hydrodynamic effects can be the source of dynamic instability in the form of seal wobble.

Sharoni, A.↗

NASA NTRS1979

Squeeze effects in radial face seals

Squeeze effects in a liquid lubricated radial face seal are analyzed. The analysis considers face misalignment with both axial and angular vibrations of the primary seal ring. Translational, rotational, and cross-coupled damping coefficients of the fluid film are derived analytically from a solution of the Reynolds equation utilizing the narrow seal approximation. Results are given for a wide range of practical radius ratios. At each radius ratio, the complete range of angular misalignment - from parallel faces to touch down - is covered. It is shown that squeeze effects in face seals are usually larger than the more familiar hydrodynamic effects. These effects play an important role in the seal's mechanism of operation and therefore have to be considered in any realistic seal model.

Etsion, I.↗

NASA NTRS1979

The effect of coning on radial forces in misaligned radial face seals

The effect of coning on radial forces in face seals having angular misalignment is analyzed. Both the hydrostatic and hydrodynamic components of the resultant radial force are presented. It is shown that the displacement of the primary seal ring due to the action of radial forces is always in a direction which may cause inward pumping. However, in most cases the radial force is very small.

Etsion, I.↗

NASA NTRS1979

Performance of end-face seals with diametral tilt and coning - Hydrostatic effects

A face seal model is analyzed, taking into account both diametral tilt and coning of the primary seal ring. The Reynolds equation for incompressible fluid is solved analytically using the narrow seal approximation. The solution covers a wide range of tilt and coning angles, from complete alignment to touch-down. Seal performance like axial force, tilting moment, axial and angular stiffness, and leakage are analyzed. It is found that interaction between diametral tilt and coning strongly affects seal performance.

Etsion, I.↗