Search NASA⌕ Search

Engineering topics

Evans, T. E.

Publications and source records attributed to Evans, T. E..

At least 19 records

Non-linear MHD modelling of edge localized modes suppression by resonant magnetic perturbations in ITER

Edge localized modes (ELMs) suppression by resonant magnetic perturbations (RMPs) was studied with the non-linear magneto-hydro-dynamic (MHD) code JOREK for the ITER H-mode scenarios at 15 MA, 12.5 MA, 10 MA/5.3 T. In this study, the main aim was to demonstrate that ELMs can be suppressed by RMPs while the divertor 3D footprints of heat and particle fluxes remain within divertor material limits. The unstable peeling–ballooning modes responsible for ELMs without RMPs were modelled first for each scenario using numerically accessible parameters for ITER. Then the stabilization of ELMs by RMPs was modelled with the same parameters. RMP spectra, optimized by the linear MHD MARS-F code, with main toroidal harmonics N = 2, N = 3, N = 4 have been used as boundary conditions of the computational domain of JOREK, including realistic RMP coils, main plasma, scrape off layer (SOL) divertor and realistic first wall. The model includes all relevant plasma flows: toroidal rotation, two fluid diamagnetic effects and neoclassical poloidal friction. With RMPs, the main toroidal harmonic and the non-linearly coupled harmonics remain dominant at the plasma edge, producing saturated modes and a continuous MHD turbulent transport thereby avoiding ELM crashes in all scenarios considered here. The threshold for ELM suppression was found at a maximum RMP coils current of 45 kAt–60 kAt compared to the coils maximum capability of 90 kAt. In the high beta poloidal steady-state 10 MA/5.3 T scenario, a rotating QH-mode without ELMs was observed even without RMPs. In this scenario with RMPs N = 3, N = 4 at 20 kAt maximum current in RMP coils, similar QH-mode behaviour was observed however with dominant edge harmonic corresponding to the main toroidal number of RMPs. The present MHD modelling was limited in time by few tens of ms after RMPs were switched on until the magnetic energy of the modes saturates. As a consequence the thermal energy was still evolving on this time scale, far from the ITER confinement time scale and hence only the form of 3D footprints on the divertor targets can be indicated within this set-up. Also note, that the divertor physics was missing in this model, so realistic values of fluxes are out of reach in this modelling. However the stationary 3D divertor and particle fluxes could be simply extrapolated from these results to the stationary situation considering that a large power fraction should be radiated in the core and SOL and only about 50 MW power is going to the divertor, which is an arbitrary, but reasonable number used here. The 3D footprints with RMPs show the characteristic splitting with the main RMP toroidal symmetry. The maximum radial extension of the footprints typically was ~20 cm in inner divertor and ~40 cm in outer divertor with stationary heat fluxes decreasing further out from the initial strike point from ~5 MW m ₋2 to ~1 MW m ₋2 assuming a total power in the divertor and walls is 50 MW. The heat fluxes remain within the divertor target and baffle areas, however with rather small margin in the outer divertor which could be an issue for the first wall especially in transient regimes when part of the plasma thermal energy is released due to switching on the RMP coils. This fact should be considered when RMPs are applied with a more favorable application before or soon after the L–H transition, although optimization is required to avoid increasing the L–H power threshold with RMPs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental inference of flux tunneling between magnetic island chains in tokamaks

We report confinement bifurcations due to flux tunneling in magnetic islands in toroidal plasmas. This occurs in 2/1 islands, triggered by decoupling of non-overlapping adjacent 5/2 islands. While subject to electron cyclotron current drive (ECCD), the temperature at the 2/1 O-point is flat before but peaks after decoupling. Here, this is shown to be due to a bifurcation from stochastic to nested magnetic structure, caused by the removal of flux tunneling through intersecting manifolds of overlapping heteroclinic tangles. 2/1 island stability correlates with coupling events in an ITER baseline scenario plasma where ECCD can not stabilize the coupled islands, showing the critical impact of flux tunneling on disruption avoidance in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

L-H transition trigger physics in ITER-similar plasmas with applied n = 3 magnetic perturbations

The L–H transition power threshold PLH is observed to increase with applied n = 3 resonant magnetic perturbations (RMP) in ITER-similar-shape plasmas with balanced neutral beam torque injection in DIII-D. The increase is most pronounced with added electron–cyclotron heating: PLH increases with decreasing edge plasma collisionality as PLH/PLH-08 ~ (ν*)−0.5, where PLH-08 is the 2008 ITPA multi-machine power threshold scaling. This result raises concerns for H-mode access at low edge collisionality in ITER, where RMP may have to be applied before the L–H transition to safely suppress the first edge-localized mode. Non-axisymmetric modifications with RMP include a simultaneous reduction of the radial electric field (Er) well depth and E × B shear. This can be attributed to increasing edge toroidal co-current rotation, and is consistent with substantially increased local long-wavelength turbulence (measured via beam emission spectroscopy). At high RMP perturbation strength the edge electric field Er reverses sign locally (becomes positive), with changes in dominant turbulence modes. Edge magnetic stochasticity provides an attractive explanation of the observed modifications, and the observed changes in toroidal rotation and Er are consistent with a simple fluid model describing radial electron current flow along stochastic fieldlines. The observed collisionality dependence of the L-mode edge electric field with applied RMP is also qualitatively consistent with this model. Reflectometry data indicate a significant reduction of the normalized L-mode radial density gradient a/Ln at high RMP field with simultaneous increase in radial particle flux and electron thermal flux from power balance analysis. We conjecture that the increase of PLH with RMP results from the combined effects of reduced E × B flow shear (increasing turbulent transport levels) and toroidal/poloidal flow modulation due to edge stochasticity. Initial experiments indicate that non-resonant n = 3 magnetic perturbations lead only to relatively small changes in Er, E × B shear and fluctuation characteristics, and have less impact on the L–H transition power threshold. This motivates further exploration of the RMP spectrum dependence of PLH for possible mitigation of the observed threshold increase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pedestal collapse by resonant magnetic perturbations

Pedestal collapse (i.e., the complete loss of the edge transport barrier (ETB)) in DIII-D H-mode plasmas occurs when resonant magnetic perturbations (RMPs) penetrate the steep gradient region at the plasma edge. Normally, RMP driven magnetic islands can occur at the top and bottom of the H-mode pedestal and these islands generate conditions consistent with edge-localized-mode (ELM) suppression and density pump-out, respectively, based on nonlinear two-fluid MHD simulations. In contrast, MHD simulations show that the steep pressure gradient region between the top and bottom of the DIII-D pedestal is generally immune to resonant field penetration due to large local E × B and diamagnetic flows. By this fortuitous circumstance, the edge-transport-barrier and H-mode confinement can be maintained while achieving ELM suppression. However, pedestal collapse can occur in DIII-D when the screening flows are inadequate to prevent field penetration in the steep gradient region of the pedestal. Non-linear two-fluid MHD simulations support the role of resonant field penetration in pedestal collapse for DIII-D H-mode plasmas with weak edge E × B and diamagnetic screening flows. ITER will likely have weaker edge screening flows than present experiments due to its much larger size, making it more susceptible to resonant field penetration in the steep gradient region of the pedestal. Analysis of model ITER equilibria demonstrates that resonant field penetration in the steep pressure gradient region is possible for RMP levels of the order required for ELM suppression. The effect of such penetration on the ITER pedestal will depend sensitively on the resulting degree of island overlap.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Experimental Observation of Magnetic Island Heteroclinic Bifurcation in Tokamaks

We report empirical observations of magnetic island heteroclinic bifurcation for the first time. This behavior is observed in interacting coupled 2/1 tearing modes in the core of a DIII-D tokamak plasma. Poincaré maps constrained by measured magnetic amplitudes and phasing show bifurcation from heteroclinic to homoclinic topology in the 2/1 island as the 4/2 relative amplitude (R 4/2 ) decreases. Initially, the local electron temperature peak in the 2/1 island splits, consistent with two O points. As R 4/2 decreases a single peak forms, consistent with one O point. Lastly, these call for developing tearing stability theory and control solutions for heteroclinic islands in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observations of heteroclinic bifurcations in resistive magnetohydrodynamic simulations of the plasma response to resonant magnetic perturbations

A class of topological magnetic island bifurcations that has not previously been observed in toroidal plasmas is described. Increasing an externally applied three-dimensional magnetic field in resistive magnetohydrodynamic simulations results in the asymmetric elongation of resonant island flux surfaces followed by a sequence of heteroclinic bifurcations. Here, these bifurcations produce new sets of hyperbolic-elliptic fixed points as predicted by the Poincaré-Birkoff fixed point theorem. Field line calculations verify that the new fixed points do not connect to those of the prebifurcated islands as required for heteroclinic bifurcations on a torus with winding numbers composed of common integer factors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the stability and stationarity of the Super H-mode combined with an ion transport barrier in the core

The Super H-mode, a regime with high pedestal pressure and stored energy, is explored on DIII-D and combined with an ion transport barrier in the plasma core to increase performance. A significant improvement of ion temperatures and confinement is facilitated by favorable conditions such as high rotational shear and high ion pedestal temperatures. As a result of a rise in density and simultaneous decrease in rotation, the ion transport barrier disappears during the discharge evolution, leading to a transition from a very high confinement state at early times, to a reduced but still high confinement phase. Additionally, in many discharges, a global MHD event consistent with the coupling of a destabilized internal mode to an edge localized mode (ELM) causes a large energy loss and leads to a reorganization of the plasma into a lower temperature, higher density state. Depending on the magnitude of the global MHD event, the plasma edge collisionality can increase significantly and shift the operational boundary from the peeling to the ballooning side, which can be understood as a drop out of the Super H-mode channel into standard H-mode. Hence, in Super H-mode discharges with ion transport barriers, both the improved pedestal height and rotational shear contribute to the high stored energy. Here, at very low levels of rotation, the confinement factor for SH modes is still expected to exceed standard H-mode by 20-30 %. With their overall stationarity and high-performance levels, Super H-mode discharges provide an attractive regime for ITER and may enable a more compact design of future fusion power plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimizing the Super H-mode pedestal to improve performance and facilitate divertor integration

Access to Super H-mode is demonstrated for moderately shaped plasmas in agreement with EPED predictions. In particular, Super H-mode is realized in a DIII-D shape that is accessible to the JET tokamak. The reduced triangularity of the JET-compatible shape compared to previous Super H-mode plasma shapes does not prevent deep ascension into the so-called Super H-mode “channel”. Operationally, access is enabled and optimized by a delaying the neutral beam power injection and thus protracting the L-H transition. In highly shaped DIII-D plasmas, the injection of nitrogen sufficient for the establishment of a radiative divertor by is shown to be possible during Super H-mode without pedestal degradation. Here, due to its increased stored energy and radiative divertor integration capabilities, the Super H-mode is a promising candidate as operating regime for JET, ITER and future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhanced helium exhaust during edge-localized mode suppression by resonant magnetic perturbations at DIII-D

Effective helium confinement time, τ p * ,He , and its ratio with energy confinement time, τ p * ,He / τ E , are key metrics quantifying the suitability of fusion plasmas for a continuous burn. Comparisons in the DIII-D tokamak of discharges with suppression of edge localized modes (ELMs) by resonant magnetic field perturbations (RMPs) to the corresponding unperturbed ELMy discharges found that both of these metrics were strongly reduced, by a factor of approximately 2, after application of the RMPs. This reduction in τ p * ,He during RMP ELM suppression was observed in the plasma core, edge, and pumping plenum, where higher neutral helium concentration during RMPs was also measured. In conclusion, these findings provide evidence that future devices employing RMP ELM suppression may meet or even exceed the helium exhaust provided by the ELMs themselves, reducing helium ash, and thus maintaining high fusion gain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Divertor currents during type-I edge-localized modes on the DIII-D tokamak

Measurements of divertor currents on DIII-D lead to new insights in nonlinear edge-localized mode (ELM) dynamics and a possible mechanism to explain their explosive growth. Rapidly oscillating currents flowing into the divertor before a significant increase in divertor heat flux occurs are measured with an array of shunted tiles and characterized. Extrapolation results in total n = 0 currents of 5–10 kA flowing into a concentric circle near the strike point. The detected Fourier harmonics appear consistent with a mix of low- n modes ( n < 4) with currents up to 4 kA. A heuristic framework for ELM currents is developed based on thermoelectric origin of the tile currents with flow through regions inside of the nominal separatrix and found consistent with the current measurements. A current flow through the confined plasma leading to increased stochasticity and transport at the plasma edge could provide a mechanism for additional nonlinear growth as sought for in computational ELM simulations. Results also imply that ELM currents may open the possibility to manipulate the ELM character by perturbations through non-axisymmetric divertor bias or tile insulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

L – H transition trigger physics in ITER-similar plasmas with applied n = 3 magnetic perturbations

In this work, the L – H transition power threshold Ρ LH is observed to increase with applied n = 3 Resonant Magnetic Perturbations (RMP) in ITER-similar-shape (ISS) plasmas with balanced neutral beam torque injection in DIII-D. The increase is most pronounced with added ECH: Ρ LH increases with decreasing edge plasma collisionality as Ρ LH / Ρ LH-08 ~ ( v *) -0.5 , where Ρ LH-08 is the 2008 ITPA multi-machine power threshold scaling. This result raises concerns for H-mode access at low edge collisionality in ITER, where resonant magnetic perturbations (RMP) may have to be applied before the L – H transition to safely suppress the first ELM. Non-axisymmetric modifications with RMP include a simultaneous reduction of the radial electric field ( E r ) well depth and E &times; B shear. This can be attributed to increasing edge toroidal co-current rotation, and is consistent with substantially increased local long-wavelength turbulence [measured via Beam Emission Spectroscopy (BES)]. At high RMP perturbation strength the edge electric field E r reverses sign locally (becomes positive), with changes in dominant turbulence modes. Edge magnetic stochasticity provides an attractive explanation of the observed modifications, and the observed changes in toroidal rotation and E r are consistent with a simple fluid model describing radial electron current flow along stochastic fieldlines. The observed collisionality dependence of the L-mode edge electric field with applied RMP is also qualitatively consistent with this model. Reflectometry data indicate a significant reduction of the normalized L-mode radial density gradient a/L n at high RMP field with simultaneous increase in radial particle flux and electron thermal flux from power balance analysis. We conjecture that the increase of Ρ LH with RMP results from the combined effects of reduced E &times; B flow shear (increasing turbulent transport levels) and toroidal/poloidal flow modulation due to edge stochasticity. Initial experiments indicate that non-resonant n = 3 magnetic perturbations lead only to relatively small changes in E r , E &times; B shear and fluctuation characteristics, and have less impact on the L – H transition power threshold. In conclusion, this motivates further exploration of the RMP spectrum dependence of Ρ LH for possible mitigation of the observed threshold increase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First observation of plasma healing via helical equilibrium in tokamak disruptions

A prompt transition of equilibrium states in a disruptive plasma is observed in the presence of three-dimensional (3D) resonant magnetic fields. A dominantly stochastic field line state heals into a 3D equilibrium with intact flux surfaces, resembling a single helicity magnetic island in the plasma core. As a consequence, the current quench process is bifurcated, i.e., from a completed quench accompanied by a vertically unstable disruption to a rapid termination of current decay followed by a full recovery to its predisruption value. Finally, this observation implies prompt stochastic fields healing through the rapid non-linear growth of magnetic island in plasma core may provide a plausible path for a soft-landing scenario of tokamak disruption in high plasma current regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of equilibrium field coil misalignments on the divertor footprints in NSTX-U

The presence of error fields in a tokamak device is inevitable, so it is of fundamental importance to understand their impact on the operation of the device and therefore up to what level they can be tolerated. In this paper a prediction of the impact on the magnetic footprints on the divertor plates due to the misalignment of NSTX-U equilibrium coils is presented. Resistive MHD solutions are used to predict the magnetic field perturbations experienced by the field lines due to the presence of error fields. A linear relation between the magnitude of the misalignment and the area of the magnetic footprints is found, as well as an inverse proportionality between the size of a magnetic footprint and the plasma penetration of the field lines composing the footprint. This study is intended as a starting point in the process of investigating divertor footprints associated with the plasma response to intrinsic error fields with resistive MHD codes. A basic interpretation of the results suggests that large footprints resulting from equilibrium coils misalignment may be desirable, to some extent, to decrease the peak heat load on the divertor components. Lastly, a more complete interpretation of the results presented here will involve a number of complex physics issues, for example pedestal transport and stability along with the role of various scrape-off layer and divertor processes, as well as experimental data to confirm the predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Topological bifurcation of magnetic islands in NSTX-U

The topological bifurcation of magnetic islands is observed in two M3D-C1 linear resistive MHD calculations of model NSTX-U equilibria during the application of small 3D magnetic perturbation fields. In comparing to a DIII-D ELM suppression case, reconstructed from shot 147170 at time slice 3745 ms, we propose that stronger kink response in the NSTX-U plasma may be the primary causes of the bifurcations. Island evolution and bifurcation in both the DIII-D and the two NSTX-U cases with the increase of perturbation current are analyzed. Further, a hypothesis is proposed that such magnetic island topology bears an intrinsic property to confine charged particles and cause their density inside the islands to rise, which is examined by implementing a random kick algorithm in the magnetic field line integration code TRIP3D-GPU to approximate electron collisional transport. Although full consideration of all forces between electrons is missing as it requires 3D large scale kinetic simulation in toroidal geometry, the positive result of this approximate transport simulation does provide first step confirmation towards fully validating the hypothesis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct measurements of internal structures of born-locked modes and the key role in triggering tokamak disruptions

The evolution of the magnetic topology between the outer separatrix of a large m = 2/ n = 1 island ( m and n : poloidal and toroidal numbers) and the last closed flux surface after mode locking is, for the first time, directly measured. Edge locked island chains with multiple helicity and very narrow widths are discovered to be destabilized and govern the cooling process in the plasma peripheral region. Furthermore, these edge small nonrotating islands are initially well separated from the 2/1 island, leading to a long quasistationary phase, but later trigger thermal quench immediately after they start to overlap with the 2/1 island, producing a broad stochastic layer deep into the plasma midradius.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Imaging divertor strike point splitting in RMP ELM suppression experiments in the DIII-D tokamak [Imaging divertor strike point splitting in RMP ELM suppression experiments]

Fast visible imaging of the lower divertor from above is used to study the structure and dynamics of lobes induced by resonant magnetic perturbations (RMPs) in Edge-Localized Mode (ELM) suppression experiments in DIII-D. The best compromise between the amount of light and sharp imaging was obtained using emission at 601 nm from Fulcher band molecular deuterium. Multiple spatially resolved peaks in the D 2 emission, taken as a proxy for the particle flux, are readily resolved during RMPs, in contrast to the heat flux measured by infrared cameras, which shows little spatial structure in ITER-like conditions. The 25 mm objective lens provides high spatial resolution (2–4 mm/pixel) from the centerpost to the outer shelf over 40° toroidally that overlaps the field of view of the IRTV that measures the divertor heat flux, allowing direct comparison in non-axisymmetric discharges. The image is coupled to a Phantom 7.3 camera using a Schott wound fiber bundle, providing high temporal resolution that allows the lobe dynamics to be resolved between ELMs and across ELM suppression onset. Furthermore, these measurements are used to study the heat and particle flux in 3D magnetic fields and to validate models for the plasma response to RMPs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗