Engineering topics

Ewing, Jacob

Publications and source records attributed to Ewing, Jacob.

6 records

DOE OSTI2024

Properties of V-defect injectors in long wavelength GaN LEDs studied by near-field electro- and photoluminescence

The efficiency of multiple quantum well (QW) light emitting diodes (LEDs) to a large degree depends on uniformity of hole distribution between the QWs. Typically, transport between the QWs takes place via carrier capture into and thermionic emission out of the QWs. In InGaN/GaN QWs, the thermionic hole transport is hindered by the high quantum confinement and polarization barriers. To overcome this drawback, hole injection through semipolar QWs located at sidewalls of V-defects had been proposed. However, in the case of the V-defect injection, strong lateral emission variations take place. In this work, we explore the nature of these variations and the impact of the V-defects on the emission spectra and carrier dynamics. The study was performed by mapping electroluminescence (EL) and photoluminescence (PL) with a scanning near-field optical microscope in LEDs that contain a deeper well that can only be populated by holes through the V-defects. Applying different excitation schemes (electrical injection and optical excitation in the far- and near-field), we have shown that the EL intensity variations are caused by the lateral nonuniformity of the hole injection. We have also found that, in biased structures, the PL intensity and decay time in the V-defect regions are only moderately lower that in the V-defect-free regions thus showing no evidence of an efficient Shockley-–Read–Hall recombination. In the V-defect regions, the emission spectra experience a red shift and increased broadening, which suggests an increase of the In content and well width in the polar QWs close to the V-defects.

Electroluminescence↗

DOE OSTI2024

Carrier diffusion in long wavelength InGaN quantum well LEDs after injection through V-defects

The efficiency of operation of GaN-based light emitting diodes (LEDs) to a large degree relies on realization of a uniform hole distribution between multiple quantum wells (QWs) of the active region. Since the direct thermionic transport between the QWs is inefficient, the hole injection through semipolar {$10\bar{1}1$} QWs that form on the facets of V-defects has been suggested as an alternative approach. However, for an efficient LED operation, the carrier distribution should be uniform not only vertically, between the QWs but also laterally, within individual QWs. In this work, the lateral carrier distribution in long wavelength InGaN/GaN QW LEDs is studied by the scanning near-field optical microscopy. The measurements have shown that emission is concentrated around the V-defect injectors. At high currents, the diffusion length of holes in polar QWs was found to be ∼0.6–1 μm and the hole diffusion coefficient ∼0.6 cm 2 /s. The obtained data should aid design of the V-defect injectors for a laterally uniform carrier distribution in the active region QWs.

Current crowding↗

DOE OSTI2023

Experimental evidence of hole injection through V-defects in long wavelength GaN-based LEDs

Hole injection through V-defect sidewalls into all quantum wells (QWs) of long wavelength GaN light emitting diodes had previously been proposed as means to increase efficiency of these devices. In this work, we directly tested the viability of this injection mechanism by electroluminescence and time-resolved photoluminescence measurements on a device in which QW furthest away from the p-side of the structure was deeper, thus serving as an optical detector for presence of injected electron–hole pairs. Emission from the detector well confirmed that, indeed, the holes were injected into this QW, which could only take place through the {$10\bar{1}1$} V-defect sidewalls. Unlike direct interwell transport by thermionic emission, this transport mechanism allows populating all QWs of a multiple QW structure despite the high potential barriers in the long wavelength InGaN/GaN QWs.

Atomic force microscopy↗

DOE OSTI2023

Origins of the high-energy electroluminescence peaks in long-wavelength (~495–685 nm) InGaN light-emitting diodes

We investigate the unexpected high-energy electroluminescence (EL) peaks observed in long-wavelength InGaN light-emitting diodes (LEDs) with ground state emission peaks between ~495 and 685 nm by studying the EL spectra of LEDs with varying quantum well (QW) thicknesses and indium compositions. In addition to the ground state emission, two high-energy emission peaks were observed in the LEDs with thick QWs and high indium compositions. The less energetic high-energy emission peak (2.4–2.6 eV) is attributed to the optical transitions involving excited states. Factors influencing the excited state transitions, such as the QW thickness and indium compositions, were also examined by simulations to better understand the occurrence of these transitions. The more energetic high-energy emission peak (2.8–3.1 eV) originates from V-defect sidewalls and was verified through micro-photoluminescence measurements. Identification of the high-energy emission peaks is essential as it enables targeted epitaxial or growth optimizations to minimize or eliminate these undesirable emission peaks. In conclusion, this work demonstrates the importance of using thin QWs to suppress the unwanted high-energy emissions due to excited state transitions and V-defect sidewalls for long-wavelength InGaN LEDs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2023

Structure of V-defects in long wavelength GaN-based light emitting diodes

The V-defect is a naturally occurring inverted hexagonal pyramid structure that has been studied in GaN and InGaN growth since the 1990s. Strategic use of V-defects in pre-quantum well superlattices or equivalent preparation layers has enabled record breaking efficiencies for green, yellow, and red InGaN light emitting diodes (LEDs) utilizing lateral injection of holes through the semi-polar sidewalls of the V-defects. In this article, we use advanced characterization techniques such as scattering contrast transmission electron microscopy, high angle annular dark field scanning transmission electron microscopy, x-ray fluorescence maps, and atom probe tomography to study the active region compositions, V-defect formation, and V-defect structure in green and red LEDs grown on (0001) patterned sapphire and (111) Si substrates. We identify two distinct types of V-defects. The “large” V-defects are those that form in the pre-well superlattice and promote hole injection, usually nucleating on mixed (Burgers vector b = ±a±c⁠) character threading dislocations. In addition, “small” V-defects often form in the multi-quantum well region and are believed to be deleterious to high-efficiency LEDs by providing non-radiative pathways. The small V-defects are often associated with basal plane stacking faults or stacking fault boxes. Furthermore, we show through scattering contrast transmission electron microscopy that during V-defect filling, the threading dislocation, which runs up the center of the V-defect, will “bend” onto one of the six {10$\overline{1}$1} semi-polar planes. In conclusion, this result is essential to understanding non-radiative recombination in V-defect engineered LEDs.

42 ENGINEERING↗

DOE OSTI2022

Influence of Superlattice Structure on V-Defect Distribution, External Quantum Efficiency and Electroluminescence for Red InGaN Based µLEDs on Silicon

Achieving high quantum efficiency in long-wavelength LEDs has posed a significant challenge to the solid-state lighting and display industries. In this article, we use V-defect engineering as a technique to achieve higher efficiencies in red InGaN LEDs on (111) Si through lateral injection. We investigate the effects of superlattice structure on the V-defect distribution, the electroluminescence properties, and the external quantum efficiency. Increasing the relative thickness of In in the InGaN/GaN superlattice and the total superlattice thickness correlate with a reduction of active region defects and increased external quantum efficiencies. The highest measured on-chip EQE was 0.15% and based on Monte-Carlo ray tracing simulations for light extraction we project this would correspond to a flip-chip EQE of ~2.5%.

36 MATERIALS SCIENCE↗