Engineering topics

Fabian, John C.

Publications and source records attributed to Fabian, John C..

6 records

NASA NTRS2012

NASA Environmentally Responsible Aviation High Overall Pressure Ratio Compressor Research Pre-Test CFD

This paper describes a collaborative and cost-shared approach to reducing fuel burn under the NASA Environmentally Responsible Aviation project. NASA and General Electric (GE) Aviation are working together aa an integrated team to obtain compressor aerodynamic data that is mutually beneficial to both NASA and GE Aviation. The objective of the High OPR Compressor Task is to test a single stage then two stages of an advanced GE core compressor using state-of-the-art research instrumentation to investigate the loss mechanisms and interaction effects of embedded transonic highly-loaded compressor stages. This paper presents preliminary results from NASA's in-house multistage computational code, APNASA, in preparation for this advanced transonic compressor rig test.

Celestina, Mark L.↗

NASA NTRS2008

Unsteady Analysis of Blade and Tip Heat Transfer as Influenced by the Upstream Momentum and Thermal Wakes

The effect of the upstream wake on the blade heat transfer has been numerically examined. The geometry and the flow conditions of the first stage turbine blade of GE s E3 engine with a tip clearance equal to 2 percent of the span was utilized. Based on numerical calculations of the vane, a set of wake boundary conditions were approximated, which were subsequently imposed upon the downstream blade. This set consisted of the momentum and thermal wakes as well as the variation in modeled turbulence quantities of turbulence intensity and the length scale. Using a one-blade periodic domain, the distributions of unsteady heat transfer rate on the turbine blade and its tip, as affected by the wake, were determined. Such heat transfer coefficient distribution was computed using the wall heat flux and the adiabatic wall temperature to desensitize the heat transfer coefficient to the wall temperature. For the determination of the wall heat flux and the adiabatic wall temperatures, two sets of computations were required. The results were used in a phase-locked manner to compute the unsteady or steady heat transfer coefficients. It has been found that the unsteady wake has some effect on the distribution of the time averaged heat transfer coefficient on the blade and that this distribution is different from the distribution that is obtainable from a steady computation. This difference was found to be as large as 20 percent of the average heat transfer on the blade surface. On the tip surface, this difference is comparatively smaller and can be as large as four percent of the average.

Ameri, Ali A.↗

NASA NTRS2007

Unsteady Turbine Blade and Tip Heat Transfer Due to Wake Passing

The geometry and the flow conditions of the first stage turbine blade of GE s E3 engine have been used to obtain the unsteady three-dimensional blade and tip heat transfer. The isothermal wall boundary condition was used. The effect of the upstream wake of the first stage vane was of interest and was simulated by provision of a gust type boundary condition upstream of the blades. A one blade periodic domain was used. The consequence of this choice was explored in a preliminary study which showed little difference in the time mean heat transfer between 1:1 and 2:3 vane/blade domains. The full three-dimensional computations are of the blade having a clearance gap of 2 percent the span. Comparison between the time averaged unsteady and steady heat transfer is provided. It is shown that there is a significant difference between the steady and time mean of unsteady blade heat transfer in localized regions. The differences on the suction side of the blade in the near hub and near tip regions were found to be rather significant. Steady analysis underestimated the blade heat transfer by as much as 20 percent as compared to the time average obtained from the unsteady analysis. As for the blade tip, the steady analysis and the unsteady analysis gave results to within 2 percent.

Ameri, Ali A.↗

NASA NTRS2007

Effects of Unsteadiness Due to Wake Passing on Rotor Blade Heat Transfer

14. ABSTRACT In a gas turbine engine, the turbine rotor blades are buffeted by the wakes of the vanes located upstream. There is a transient effect from the passing of wakes on the blade heat transfer. This transient effect has been computed for a representative rotor by introducing a wake upstream via an unsteady inlet flow boundary condition, or "gust" condition. Two cases of turbulent flow and laminar flow with Reynolds numbers of 385,000 and 385 respectively were considered. For the turbulent flow case a quasi-steady calculation was also performed. The variation in the unsteady heat transfer coefficient was found to be as high as 120 percent of the mean. For the turbulent flow case a quasisteady calculation was also performed. The time mean of the unsteady heat transfer, the mean of the quasi-steady variations and the steady results agree reasonably well on all blade locations except for the turbulent results which differ near the leading edge. The quasi-steady heat transfer results do not agree with the instantaneous unsteady results, although the time-mean values are similar.

Ameri, Ali A.↗

NASA NTRS2006

Code for Multiblock CFD and Heat-Transfer Computations

The NASA Glenn Research Center General Multi-Block Navier-Stokes Convective Heat Transfer Code, Glenn-HT, has been used extensively to predict heat transfer and fluid flow for a variety of steady gas turbine engine problems. Recently, the Glenn-HT code has been completely rewritten in Fortran 90/95, a more object-oriented language that allows programmers to create code that is more modular and makes more efficient use of data structures. The new implementation takes full advantage of the capabilities of the Fortran 90/95 programming language. As a result, the Glenn-HT code now provides dynamic memory allocation, modular design, and unsteady flow capability. This allows for the heat-transfer analysis of a full turbine stage. The code has been demonstrated for an unsteady inflow condition, and gridding efforts have been initiated for a full turbine stage unsteady calculation. This analysis will be the first to simultaneously include the effects of rotation, blade interaction, film cooling, and tip clearance with recessed tip on turbine heat transfer and cooling performance. Future plans call for the application of the new Glenn-HT code to a range of gas turbine engine problems of current interest to the heat-transfer community. The new unsteady flow capability will allow researchers to predict the effect of unsteady flow phenomena upon the convective heat transfer of turbine blades and vanes. Work will also continue on the development of conjugate heat-transfer capability in the code, where simultaneous solution of convective and conductive heat-transfer domains is accomplished. Finally, advanced turbulence and fluid flow models and automatic gridding techniques are being developed that will be applied to the Glenn-HT code and solution process.

Fabian, John C.↗

NASA NTRS2005

Object-Oriented Version of Glenn-HT Code Released: Glenn-HT2000

NASA Glenn Research Center s General Multi-Block Navier-Stokes Convective Heat Transfer Code (Glenn-HT) has been used extensively to predict heat transfer and fluid flow for a variety of steady gas turbine engine problems. Efforts have focused on turbine heat transfer, where computations have modeled tip clearance, internal coolant, and film cooling flows. Excellent agreement has been achieved for a variety of experimental test cases, and results have been published in over 40 technical publications. The code is available to U.S. industry and has been used by several domestic gas turbine engine companies. The following figure shows a typical flow solution from the Glenn-HT code for a film-cooled turbine blade.

Heidmann, James D.↗