Engineering topics

Fabris, G.

Publications and source records attributed to Fabris, G..

7 records

NASA NTRS1992

Hot wire/film behavior in low-temperature gases

Commercially available hot wires/films were used to measure the velocities of evaporated hydrogen or helium gas during cryogenic mixing experiments. Hot wires were found to be too delicate to use in this harsh environment. Hot films were rugged enough to use at cryogenic temperatures even though they failed after a number of thermal cycles. Since the hot films have small aspect ratios, 13.4 and 20, they are quite sensitive to the thermal loading, Tw/Tg, even with a correction for the conduction end loss. In general, although the increase of the Nusselt number with Reynolds number at low temperatures was similar to that at room temperature, there was also a pronounced variation with Tw/Tg over the large range of 1.2 to 12 investigated.

Kwack, E. Y.↗

NASA NTRS1992

Prediction of performance of two-phase flow nozzle and liquid metal magnetohydrodynamic (LMMHD) generator for no slip condition

Two-phase LMMHD energy conversion systems have potentially significant advantages over conventional systems such as higher thermal efficiency and substantial simplicity with lower capital and maintenance costs. Maintenance of low velocity slip is of importance for achieving high generator efficiency. A bubbly flow pattern ensures very low velocity slip. The full governing equations have been written out, and a computer prediction code has been developed to analyze performance of a two-phase flow LMMHD generator and nozzle under conditions of no slip. Three different shapes of a LMMHD generator have been investigated. Electrical power outputs are in the 20 kW range. Generator efficiency exceeds 71 percent at an average void fraction of about 70 percent. This is an appreciable performance for a short generator without insulating vanes for minimizing electrical losses in the end regions.

Fabris, G.↗

NASA NTRS1990

Two-phase flow bubbly mixing for liquid metal magnetohydrodynamic energy conversion

Experiments aimed at improving mixer design and investigating the effects of surfactants on the two-phase mixture in two-phase liquid metal MHD (LMMHD) energy conversion systems are described. In addition to conventional photography, flash X-ray imaging was used as a diagnostic tool. It was demonstrated that a high void fraction (0.8) and low velocity slip ratio (1.2) two-phase homogeneous bubbly mixture can be created. It is expected that such a two-phase mixture can be further expanded in a LMMHD generator while maintaining low velocity slip. In such a way, high generator and overall system efficiency would be achieved, making LMMHD systems competitive for a number of commercial applications.

Fabris, G.↗

NASA NTRS1989

Direct conversion technology

The overall objective of the Direct Conversion Technology task is to develop an experimentally verified technology base for promising direct conversion systems that have potential application for energy conservation in the end-use sectors. This report contains progress of research on the Alkali Metal Thermal-to-Electric Converter (AMTEC), and on the Two-Phase Liquid-Metal Magnetohydrodynamic Electrical Generator (LMMHD) for the period January 1, 1989 through December 31, 1989. Research on these concepts was initiated during October 1987. Reports prepared on previous occasions contain discussions on the following other direct conversion concepts: thermoelectric, pyroelectric, thermionic, thermophotovoltaic, thermoacoustic, thermomagnetic, thermoelastic (nitinol heat engines); and also, more complete discussions of AMTEC and LMMHD systems.

Massier, Paul F.↗

NASA NTRS1988

Direct conversion technology

The overall objective of the Direct Conversion Technology task is to develop an experimentally verified technology base for promising direct thermal-to-electric energy conversion systems that have potential application for energy conservation in the end-use sectors. This report contains progress of research on the Alkali Metal Thermal-to-Electric Converter (AMTEC), and on the Two-Phase Liquid-Metal MHD Electrical Generator (LMMHD) for the period January 1988 through December 1988. Research on these concepts was initiated during October 1987. In addition, status reviews and assessments are presented for thermomagnetic converter concepts and for thermoelastic converters (Nitinol heat engines). Reports prepared on previous occasions contain discussions on the following other direct conversion concepts: thermoelectric, pyroelectric, thermionic thermophotovoltaic and thermoacoustic; and also, more complete discussions of AMTEC and LMMHD systems. A tabulated summary of the various systems which have been reviewed thus far has been prepared. Some of the important technical research needs are listed and a schematic of each system is shown.

Massier, P. F.↗

NASA NTRS1981

Multiple-scale turbulence modeling of free turbulent flows

As part of an investigation into the application of turbulence models to the computation of flows in advanced scramjet combustors, the multiple-scale turbulence model has been applied to a variety of flowfield predictions. The model appears to have a potential for improved predictions in a variety of areas relevant to combustor problems. This potential exists because of the partition of the turbulence energy spectrum that is the major feature of the model and which allows the turbulence energy dissipation rate to be out of phase with turbulent energy production. To establish the general reliability of the approach, it has been tested through comparison of predictions with experimental data. An appreciable overall improvement in the generality of the predictions is observed, as compared to those of the basic two-equation turbulence model. A Mach number-related correction is found to be necessary to satisfactorily predict the spreading rate of the supersonic jet and mixing layer.

Fabris, G.↗

NASA NTRS1981

Multiple-scale turbulence modeling of boundary layer flows for scramjet applications

As part of an investigation into the application of turbulence models to the computation of flows in advanced scramjet combustors, the multiple-scale turbulence model was applied to a variety of flowfield predictions. The model appears to have a potential for improved predictions in a variety of areas relevant to combustor problems. This potential exists because of the partition of the turbulence energy spectrum that is the major feature of the model and which allows the turbulence energy dissipation rate to be out of phase with turbulent energy production. The computations were made using a consistent method of generating experimentally unavailable initial conditions. An appreciable overall improvement in the generality of the predictions is observed, as compared to those of the basic two-equation turbulence model. A Mach number-related correction is found to be necessary to satisfactorily predict the spreading rate of the supersonic jet and mixing layer.

Fabris, G.↗