Search NASA⌕ Search

Engineering topics

Failla, Jordan

Publications and source records attributed to Failla, Jordan.

Dual Material System for Polymer Large Scale Additive Manufacturing

Big Area Additive Manufacturing (BAAM) technology allows for manufacturing of large-scale objects with a potential to reduce energy embedded in products, reduce or eliminate energy necessary for transportation of goods along with reducing the lead time and cost in some cases. Over the last few years, Oak Ridge National Laboratory (ORNL) has been focusing on large-scale printing of single material systems, typically un-reinforced or short fiber reinforced polymers, in order to address needs in stiffness-limited applications. This paper describes the development of a multi-material large-scale AM system through a collaboration with Cincinnati Inc. and Performance Feed Screw Inc. Modifications to the Big Area Additive Manufacturing (BAAM) system includes a new extruder design to accommodate a dual feed system, an expanded two-dryer system with a capacity of 273 kg/dryer, and a system that is capable of mixing pelletized materials up to 60Kg/hr. This article highlights the advantages and limitations of the multi-material system as well as potential applications.

Smith, Tyler↗

Z-Pinning approach for 3D printing mechanically isotropic materials

Conventional 3D printing approaches are restricted to building up material in a layer-by-layer format, which is more appropriately considered “2.5-D” printing. The layered structure inherently results in significant mechanical anisotropy in printed parts, causing the tensile strength in the build direction (z-axis) to be only a fraction of the in-plane strength – a decrease of 50–75% is common. In this study, a novel “z-pinning” approach is described that allows continuous material to be deposited across multiple layers within the volume of the part. Here, the z-pinning process is demonstrated using a Fused Filament Fabrication (FFF) printer for polylactic acid (PLA) and carbon fiber reinforced PLA. For both materials, z-pinning increased the tensile strength and toughness in the z-direction by more than a factor of 3.5. Direct comparisons to tensile strength in the x-axis showed a significant decrease in mechanical anisotropy as the volume of the pin was increased relative to the void in the rectilinear grid structure. In fact, the PLA sample with the largest pin volume demonstrated mechanically isotropic properties within the statistical uncertainty of the tests. Tensile test results were also analyzed relative to the functional area resisting deformation for each sample.

36 MATERIALS SCIENCE↗

Structural Health Monitoring of 3D Printed Structures

3D printed parts are used in industry for both tooling application and smaller parts in assembled structures. Articles made through polymer based additive manufacturing are anisotropic and may have defects throughout the part. For instance, the layer to layer interactions are weaker than the in-plane printing which can cause delamination of the layers. Identifying when and where the cracks form can be very difficult if the cracks are inside the structure This paper introduces an innovative patent-pending method to monitor polymer-based 3D printed structures for internal failures by printing a highly sensitive conductive material into the part itself. When a section of the conductive material inside the part is damaged or split, the resistance across the conductive pathway increases which will indicate that the article has been damaged. We present several small printed circuits and observations that show as a crack is introduced to the structure, the resistance measured increases which alerts users that a crack has formed/propagated.

Smith, Tyler↗

Z-Pinning Approach for Reducing Mechanical Anisotropy of 3D Printed Parts

The mechanical strength of extrusion-based printed parts is often greatly reduced (25-50%) in the build direction (z-direction) compared to the in-plane strength due to poor bonding between successively deposited layers. This effect can be magnified (75-90% difference) when depositing fiber-reinforced materials or larger print areas with long layer times. Therefore, a patent-pending approach has been developed that deposits material into intentionally aligned voids in the zdirection, allowing continuous material to span multiple layers. The “z-pinning” approach can be applied to several concepts for improving the interlaminar strength of extrusion-based 3D printed parts as well as techniques for applying the technology across a broad spectrum of deposition platforms and material systems. Initial experimental results demonstrate a significant improvement (>3x) in mechanical strength and (>8x) toughness for fiber reinforced components.

Duty, Chad↗

Graded Infill Structure of Wind Turbine Blade Accounting for Internal Stress in Big Area Additive Manufacturing

In additively manufactured (AM) components, infill structure significantly affects the mechanical performance of the final printed part. However, mechanical stress induced by operation loads has been so far neglected for infill patterning. Most slicers currently available in the market provide infill patterns that are uniform in shape and size regardless of the operational loading. We develop a design approach for infill patterns that accounts for the induced stress. This approach differs from topology optimization as it focuses on the porous infill, which allows the external shape of the printed part to remain intact. The proposed approach uses a computational stress analysis to control the distribution of the local density of the infill pattern. We have applied the approach to a wind turbine blade core with infill densities optimized based on the structural loads. The blade core is fabricated in our big area additive manufacturing (BAAM) system. To ensure less warpage and better inter-layer bonding, fast layer deposition is critical in BAAM system. We have optimized the tool path sequences to minimize the deposition time via the solution to the Chinese Postman Problem (CPP). For the application of wind turbine infill, the deposition from the CPP method is twice faster than the deposition from conventional slicing.

Kim, Pum↗

Parametric Analysis on Vertical Pins for Strengthening Extrusion-Based Printed Parts

For extrusion-based additive manufacturing, the mechanical performance in vertical direction (z-direction) is significantly lower than that in the printed layer plane (xy-direction). This paper presents a vertical extrusion approach across several layers to improve the mechanical properties of a 3D printed part. This approach is patent pending, and it involves depositing pins in the z-direction into predefined holes. It requires the vertical pins to mechanically engage with the surrounding structure of the holes. To maximize the mechanical performance of the printed structures with pins, we then analyzed the penetration quality of the pins with a wide range of hole depths, hole sizes, and pin volumes and obtained the relationship between the hole width and the hole depth for the full penetration of pins.

Kim, Pum↗

Additive Manufacturing of High Performance Semicrystalline Thermoplastics and Their Composites

This work investigates the use of two semi-crystalline high performance thermoplastics, polyphenylene sulfide (PPS) and poly (ether ketone ketone) (PEKK), as feedstock for fused filament fabrication process. Composites of PPS and PEKK are emerging as viable candidates for several components in aerospace and tooling industries and additive manufacturing of these materials can be extremely beneficial to lower manufacturing costs and lead times. However, these materials pose several challenges for extrusion and deposition due to some of their inherent properties as well as thermal and oxidative responses. To better understand the properties of such systems specific to 3D printing and determine the critical parameters that make them “printable”, various rheological and thermal properties have been studied for neat as well as short fiber reinforced PPS and PEKK systems. Attempts were also made to print these materials in a customized high temperature fused filament fabrication system.

Kishore, Vidya↗