Engineering topics

Falarski, M. D.

Publications and source records attributed to Falarski, M. D..

At least 19 records

NASA NTRS1984

Aerodynamic characteristics of the 40- by 80/80- by 120-foot wind tunnel at NASA Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams are discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗

NASA NTRS1984

Aerodynamic characteristics of the 40- by 80-/80- by 120-ft wind tunnel at NASA-Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams and discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗

NASA NTRS1982

Aerodynamic characteristics of a large-scale, twin tilt-nacelle V/STOL model

A subsonic tilt-nacelle V/STOL aircraft configuration is described which is powered by two turbofan engines, mounted on a single carry-through structure that is designed to maintain the thrust axis close to the center of gravity at nacelle incidences of 5-95 deg. Control during V/STOL operation, often from small ship platforms, is achieved by means of a vane assembly that is immersed in each turbofan's exhaust. Wind tunnel test data have been obtained with an 11.2-m wing span model for the vertical-to-horizontal flight transition capability of the concept. It is found that the aircraft can operate over a broad transition corridor, with sufficient maneuver capability about the trim points. The control vane exhibited linear response characteristics over a large deflection range, with little influence from power, angle of attack or ground proximity in hover. The model induced a positive ground effect in hover that increased as wheel height was approached and strake angle increased.

Falarski, M. D.↗

NASA NTRS1981

Ground effect hover characteristics of a large-scale twin tilt-nacelle V/STOL model

This paper is a summary of an analysis of the ground-effect characteristics of a large-scale twin-engine, tilt-nacelle V/STOL model. The analysis considers data from the flow field beneath the full-scale model, as well as small-scale model test data, and makes comparisons with jet-ground interactions predicted by a computer code. The data from the large-scale test comprise ground-plane surface temperatures, static pressure distribution and wall-jet total-pressure profiles, fuselage undersurface static pressures, and model forces and moments. The results indicate that the near-field flow is more complex than is indicated by either the small-scale uniform jet studies or the computer predictions. The far-field flow characteristics do show some similarity for these three cases.

Dudley, M. R.↗

NASA NTRS1981

Analysis of data from a wind tunnel investigation of a large-scale model of a highly maneuverable supersonic V/STOL fighter - STOL configuration

The surface pressure and thermal characteristics of a large-scale model of a highly maneuverable supersonic fighter with STOL capability are described. The 7.28 m span model is powered by two J-97 turbojets, operated at 9340 N thrust. It combines upper-surface and spanwise blowing to augment the lift characteristics over a wide angle-of-attack range. The most significant feature of the fighter's flow field is the leading edge vortex that forms at low alphas, grows stronger, and moves inboard as alpha is increased. Upper surface blowing enhanced the lift on the wing in both stalled and unstalled areas significantly, while generating only a modest aft shift in the center of pressure. Lift gains were greatest at high alphas and with the flap deflected. Spanwise blowing was most significant at angles-of-attack greater than 8 deg, when the jet strengthened the vortex. The 1100 F spanwise blowing jet mixed very rapidly with the wing flow field, creating a maximum temperature rise of only 300-350 F. A comparison of small-scale and large-scale model wing pressure characteristics showed similar trends created by upper surface blowing, while spanwise blowing characteristics differed considerably. Force data correlated well with semi-empirical predictions for gross thrust coefficients less than 1.0.

Falarski, M. D.↗

NASA NTRS1980

Static calibration of a two-dimensional wedge nozzle with thrust vectoring and spanwise blowing

The results of a static calibration of the two dimensional wedge nozzles on a STOL configuration of a large-scale fighter model are reported. These nozzles internally turn the efflux produced by two turbojets down 25 degrees and exhaust it over the deflected trailing edge of the wing. This arrangement provides direct thrust lift, enhances wing lift by producting supercirculation, and provides thrust vectoring by varying the deflection of the wing's trailing edge. The thrust is vectored from 10 deg to 38 deg. This system was calibrated with spanwise blowing for augmentation of the leading-edge vortex. When 16% of the turbojet efflux is blown spanwise, the thrust recovered is 92% of the thrust produced when the total efflux is exhausted longitudinally.

Harris, M. J.↗

NASA NTRS1980

Acoustic characteristics of two hybrid inlets at forward speed

A wind tunnel investigation of the acoustic and aerodynamic characteristics of two hybrid inlets installed on a JT15D-1 turbofan engine was performed. The hybrid inlets combined moderate throat Mach number and wall acoustic treatment to suppress the fan inlet noise. Acoustic and aerodynamic data were recorded over a range of flight and engine operating conditions. In a simulated flight environment, the hybrid inlets provided significant levels of suppression at both design and off-design throat Mach numbers with good aerodynamic performance. A comparison of inlet noise at quasi-static and forward-speed conditions in the wind tunnel showed a reduction in the fan tones, demonstrating the flight cleanup effect. High angles of attack produced slight increases in fan noise at the high acoustic directivity angles.

Falarski, M. D.↗

NASA NTRS1979

Aerodynamic characteristics of a large-scale semispan model with a swept wing and an augmented jet flap with hypermixing nozzles

The aerodynamic characteristics of the augmentor wing concept with hypermixing primary nozzles were investigated. A large-scale semispan model in the Ames 40- by 80-Foot Wind Tunnel and Static Test Facility was used. The trailing edge, augmentor flap system occupied 65% of the span and consisted of two fixed pivot flaps. The nozzle system consisted of hypermixing, lobe primary nozzles, and BLC slot nozzles at the forward inlet, both sides and ends of the throat, and at the aft flap. The entire wing leading edge was fitted with a 10% chord slat and a blowing slot. Outboard of the flap was a blown aileron. The model was tested statically and at forward speed. Primary parameters and their ranges included angle of attack from -12 to 32 degrees, flap angles of 20, 30, 45, 60 and 70 degrees, and deflection and diffuser area ratios from 1.16 to 2.22. Thrust coefficients ranged from 0 to 2.73, while nozzle pressure ratios varied from 1.0 to 2.34. Reynolds number per foot varied from 0 to 1.4 million. Analysis of the data indicated a maximum static, gross augmentation of 1.53 at a flap angle of 45 degrees. Analysis also indicated that the configuration was an efficient powered lift device and that the net thrust was comparable with augmentor wings of similar static performance. Performance at forward speed was best at a diffuser area ratio of 1.37.

Aiken, T. N.↗

NASA NTRS1979

Wind-tunnel investigation of highly maneuverable supersonic V/STOL fighter

Results from the initial wind-tunnel test of a large-scale, highly maneuverable supersonic V/STOL fighter model in the Ames 40- by 80-foot wind tunnel are summarized. The STOL configuration which was tested combined upper surface blowing and spanwise blowing to improve the lift characteristics over a wide angle-of-attack range. A close-coupled canard was added to this configuration to create a highly maneuverable STOL aircraft. The 7.28 m (24 ft) span model was powered by two J-97 turbojet engines, each producing 9340 N (2200 lb) thrust at a pressure ratio of 2. With the nozzle flap and aileron set at 30 deg, the model produced lift coefficients greater than 4. The model was longitudinally unstable because of the forward canard position and because of the large body area of fuselage, strake, and nacelles forward of the center of gravity.

Falarski, M. D.↗

NASA NTRS1979

Aerodynamics of a tilt-nacelle V/STOL propulsion system

Tests were performed in the Ames 40 by 80 Foot Wind Tunnel on a large-scale, tilt-nacelle V/STOL propulsion system to determine its aerodynamic characteristics. Unpowered nacelle aerodynamics and power induced effects over an angle of attack range from 0 to 105 deg are presented. It is shown that: (1) the characteristics of the unpowered nacelle can be estimated with annular airfoil data, (2) the power-induced effects on the nacelle aerodynamics are significant, and (3) pitching moment can be correlated with lift and thrust.

Betzina, M. D.↗

NASA NTRS1979

Wind-tunnel investigation of the thrust augmentor performance of a large-scale swept wing model

Tests were made in the Ames 40- by 80-foot wind tunnel to determine the forward speed effects on wing-mounted thrust augmentors. The large-scale model was powered by the compressor output of J-85 driven viper compressors. The flap settings used were 15 deg and 30 deg with 0 deg, 15 deg, and 30 deg aileron settings. The maximum duct pressure, and wind tunnel dynamic pressure were 66 cmHg (26 in Hg) and 1190 N/sq m (25 lb/sq ft), respectively. All tests were made at zero sideslip. Test results are presented without analysis.

Koenig, D. G.↗

NASA NTRS1977

Large-scale V/STOL testing

Several facets of large-scale testing of V/STOL aircraft configurations are discussed with particular emphasis on test experience in the Ames 40- by 80-foot wind tunnel. Examples of powered-lift test programs are presented in order to illustrate tradeoffs confronting the planner of V/STOL test programs. It is indicated that large-scale V/STOL wind-tunnel testing can sometimes compete with small-scale testing in the effort required (overall test time) and program costs because of the possibility of conducting a number of different tests with a single large-scale model where several small-scale models would be required. The benefits of both high- and full-scale Reynolds numbers, more detailed configuration simulation, and number and type of onboard measurements increase rapidly with scale. Planning must be more detailed at large scale in order to balance the trade-offs between the increased costs, as number of measurements and model configuration variables increase and the benefits of larger amounts of information coming out of one test.

Koenig, D. G.↗

NASA NTRS1976

The aerodynamic and acoustic characteristics of an over-the-wing target-type thrust reverser model

A static test of a large-scale, over-the-wing (OTW) powered-lift model was performed. The OTW propulsion system had been modified to incorporate a simple target-type thrust reverser as well as the normal rectangular OTW exhaust nozzle. Tests were performed in both the reverse thrust and approach configurations. The thrust reverser noise created by jet turbulence mixing and the OTW approach noise were both low frequency and broadband. When scaled to a 45,400-kg (100,000-lb) aircraft, the thrust reverser and approach configurations produced peak 152-m (500-ft) sideline perceived noise levels of 110 and 105 PNdB, respectively. The aerodynamic performance of the model showed that 50% or greater reverser effectiveness can be achieved without experiencing ingestion of exhaust gas or ground debris into the engine inlets.

Falarski, M. D.↗

NASA NTRS1976

Correlation of internal surface turbulence with far-field noise of the augmentor wing propulsive-lift concept

A wind tunnel investigation was conducted to determine the nature, strength, and variation with airspeed of the acoustic sources of the augmentor wing propulsive-lift concept. The augmentor wing overall noise is dominated by the high frequency jet mixing noise characteristic of the lobed primary nozzle. The augmentor modifies the intensity and propagation characteristics of the jet sources, especially those that exist inside the augmentor. The interaction of the turbulent flow with the augmentor creates low-frequency, low-intensity surface noise and trailing edge noise. These sources dominate any jet mixing noise that is present at the low frequencies and could become significant if the jet noise was suppressed by treating the augmentor with a lining tuned to the jet noise source location. The far-field noise of the untreated augmentor is unaffected by airspeed; however, this may not be the case when the jet noise is suppressed, because the trailing edge surface pressure and correlations with far-field noise do show a reduction with forward speed.

Falarski, M. D.↗

NASA NTRS1975

Acoustic characteristics of a large scale wind-tunnel model of a jet flap aircraft

The expanding-duct jet flap (EJF) concept is studied to determine STOL performance in turbofan-powered aircraft. The EJF is used to solve the problem of ducting the required volume of air into the wing by providing an expanding cavity between the upper and lower surfaces of the flap. The results are presented of an investigation of the acoustic characteristics of the EJF concept on a large-scale aircraft model powered by JT15D engines. The noise of the EJF is generated by acoustic dipoles as shown by the sixth power dependence of the noise on jet velocity. These sources result from the interaction of the flow turbulence with flap of internal and external surfaces and the trailing edges. Increasing the trailing edge jet from 70 percent span to 100 percent span increased the noise 2 db for the equivalent nozzle area. Blowing at the knee of the flap rather than the trailing edge reduced the noise 5 to 10 db by displacing the jet from the trailing edge and providing shielding from high-frequency noise. Deflecting the flap and varying the angle of attack modified the directivity of the underwing noise but did not affect the peak noise. A forward speed of 33.5 m/sec (110 ft/sec) reduced the dipole noise less than 1 db.

Falarski, M. D.↗

NASA NTRS1975

Wind tunnel investigation of a large-scale upper surface blown-flap model having four engines

Investigations were conducted in the Ames 40- by 80-Foot Wind Tunnel to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blown flap system. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The lift of the flap system was augmented by turning the turbofan exhaust over the Coanda surface. Results were obtained for several flap deflections with several wing leading-edge configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with four engines operating. In addition, longitudinal and lateral data are presented with an engine out. The maximum lift and stall angle of the four engine model were lower than those obtained with a two engine model that was previously investigated. The addition of the outboard nacelles had an adverse effect on these values. Efforts to improve these values were successful. A maximum lift of 8.8 at an angle-of-attack of 27 deg was obtained with a jet thrust coefficient of 2 for the landing flap configuration.

Aoyagi, K.↗

NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗

NASA NTRS1973

Acoustic characteristics of a large-scale augmentor wing model at forward speed

The augmentor wing concept is being studied as one means of attaining short takeoff and landing (STOL) performance in turbofan powered aircraft. Because of the stringent noise requirements for STOL operation, the acoustics of the augmentor wing are undergoing extensive research. The results of a wind tunnel investigation of a large-scale swept augmentor model at forward speed are presented. The augmentor was not acoustically treated, although the compressor supplying the high pressure primary air was treated to allow the measurement of only the augmentor noise. Installing the augmentor flap and shroud on the slot primary nozzle caused the acoustic dependence on jet velocity to change from eighth power to sixth power. Deflecting the augmentor at constant power increased the perceived noise level in the forward quadrant. The effect of airspeed was small. A small aft shift in perceived noise directivity was experienced with no significant change in sound power. Sealing the lower augmentor slot at a flap deflection of 70 deg reduced the perceived noise level in the aft quadrant. The seal prevented noise from propagating through the slot.

Falarski, M. D.↗