Search NASA⌕ Search

Engineering topics

Fancher, Chris M.

Publications and source records attributed to Fancher, Chris M..

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Residual Stress in Cold Spray SS304L Measured Via Neutron Diffraction and Comparison of Analytical Models to Predict the Residual Stress

Here, this study employs neutron diffraction to investigate the relationship between residual stress and coating thickness in cold sprayed 304L austenitic stainless steel. Results show that shot peening predominantly impacts the residual stress profile, leading to substantial in-plane compressive force. The impact of laser heating, a widely used method to alter cold spray's microstructural properties, on the coating's residual stress is also analyzed. The findings indicate that the maximum compressive residual stress in the in-plane component is mainly independent of coating thickness, which suggests that the material properties determine the maximum residual stress. The cold sprayed deposits possessed compressive, nearly biaxial strain and stresses. After laser heating, these stresses were replaced by tensile residual stresses. Two analytical models, the Tsui and Clyne and the Boruah models, for predicting residual stresses are also evaluated, and both models provide reasonable fits to the experimental data. At this point, the deviations between the experimental results and the models are principally caused by the inability of the current models to address plastic deformation and relaxation, and the residual stresses generated by thermal gradients.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strain as a Global Factor in Stabilizing the Ferroelectric Properties of ZrO 2

Since the discovery of ferroelectricity in doped HfO 2 and ZrO 2 thin films over a decade ago, fluorite-structured ferroelectric thin films have attracted much research attention due to their excellent scalability and complementary metal-oxide semiconductor compatibility compared to conventional perovskite ferroelectric materials. Although various factors influencing the formation of the ferroelectric properties are identified, a clear understanding of the causes of the phase formation have been difficult to determine. In this work, ZrO 2 films deposited by atomic layer deposition and chemical solution deposition have resulted in films with completely different structural properties. Regardless of these differences, a general relationship between strain and phase formation is established, leading to a more unified understanding of ferroelectric phase formation in undoped ZrO 2 films, which can be applied to other fluorite-structured films.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Disorder-order transformation in Fe-50%Co fabricated via laser powder bed fusion

Fe-Co alloys are an important class of soft magnetic materials that often pose challenges in their fabrication because of the brittle B2-ordered phase. We show that laser beam powder bed fusion (PBF-LB), owing to its rapid cooling rates, offers an avenue for the fabrication of these alloys by suppressing the disorder →order phase transformation at room temperature. We use neutron diffraction to understand the phase transformations in a Fe-50%Co alloy fabricated via PBF-LB. We report that the disorder→order phase transformation in this alloy occurs concurrently via homogeneous ordering and classical nucleation and growth.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Validating the Use of Gaussian Process Regression for Adaptive Mapping of Residual Stress Fields

Probing the stress state using a high density of measurement points is time intensive and presents a limitation for what is experimentally feasible. Alternatively, individual strain fields used for determining stresses can be reconstructed from a subset of points using a Gaussian process regression (GPR). Results presented in this paper evidence that determining stresses from reconstructed strain fields is a viable approach for reducing the number of measurements needed to fully sample a component’s stress state. The approach was demonstrated by reconstructing the stress fields in wire-arc additively manufactured walls fabricated using either a mild steel or low-temperature transition feedstock. Effects of errors in individual GP reconstructed strain maps and how these errors propagate to the final stress maps were assessed. Implications of the initial sampling approach and how localized strains affect convergence are explored to give guidance on how best to implement a dynamic sampling experiment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Temperature-Dependent Thermal and Mechanical Properties of a Wire Arc Additively Manufactured Low Transformation Temperature Steel

Recent research has studied the use of low transformation temperature (LTT) martensite steel as feedstock for wire arc additive manufacturing (WAAM) and low tensile residual stresses or compressive residual stresses were detected in the printed walls. These residual stress states help to improve printed product properties such as fatigue strength and corrosion resistance. However, the thermal and mechanical properties of WAAM printed LTT martensite steel walls are largely unknown. In this work, a printed LTT martensite steel was characterized for its thermal, metallurgical, and mechanical behavior at room and elevated temperatures. The temperature-dependent specific heat capacity, thermal expansion, atomic lattice spacing, and tensile properties were measured during both heating and cooling and related to observed microstructural features and computational thermodynamics predictions. These results revealed a large hysteresis in the martensitic transformation, with a martensite start temperature of 240 °C and austenite start temperature of 680 °C. Additional thermal cycles and specimen orientation did not affect the printed specimen austenite and martensite transformations. However, it was observed that the printed metal may exhibit tempering embrittlement at about 350 °C but further studies are needed to confirm that. Further, these results suggest that a temperature control of 250 °C to 350 °C during WAAM is needed to maximize the stress reduction potential of the LTT250 martensite steel. Opportunities for future implementation of LTT martensite steels and optimization of additive manufacturing process conditions are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Implications of gnomonic distortion on electron backscatter diffraction and transmission Kikuchi diffraction

The effect of gnomonic distortion on orientation indexing of electron backscatter diffraction patterns is explored through simulation of electron diffraction patterns for sample-to-detector geometries associated with transmission Kikuchi diffraction (TKD) and electron backscatter diffraction (EBSD). Simulated data were analysed by computing a similarity index for both Hough transformed data and simulated patterns to determine the sensitivity of each method for detecting subtle differences in the effect of gnomonic distortions on electron diffraction patterns. These results indicate that the increased gnomonic distortions in electron diffraction patterns for a TKD geometry enhance the sensitivity for detecting subtle differences in interband angles. Additionally, the utilisation of a Hough transform-based indexing approach further enhances the sensitivity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Diffraction Methods for Qualitative and Quantitative Texture Analysis of Ferroelectric Ceramics

Crystallographic textures are pervasive in ferroelectrics and underpin the functional properties of devices utilizing these materials because many macroscopic properties (e.g., piezoelectricity) require a non-random distribution of dipoles. Inducing a preferred grain texture has become a viable route to improve these functional properties. X-ray and neutron diffraction have become valuable tools to probe crystallographic textures. This paper presents an overview of qualitative and quantitative methods for assessing crystallographic textures in electroceramics (domain and grain textures) and discusses their strengths and weaknesses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Temperature dependence of field-response mechanisms in 0.4Ba(Zr 0.2 Ti 0.8 )O 3 –0.6(Ba 0.7 Ca 0.3 )TiO 3

Understanding the temperature dependence of how ferroelectric materials respond to electric fields is critical for determining how best to use these materials in applications. In this study, temperature dependent in situ x-ray diffraction is used to study how field-response mechanism Ba ( Zr 0.2 Ti 0.8 ) O 3 – x ( Ba 0.7 Ca 0.3 ) TiO 3 evolves with temperature. Increasing the measurement temperature was found to slightly reduce the extent of domain reversal and the magnitude of the 111 lattice strain. Instead, these results indicate that temperature predominantly impacted the angular dependence of the 002/200 lattice strain. We attribute the observed differences in 002/200 lattice strain to the flattening of the free-energy near the tetragonal-orthorhombic phase boundary, where the flattening of the energy landscape promotes a polarization rotation response during the application of electric fields at room temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Metal Nitride Electrode Stress and Chemistry Effects on Phase and Polarization Response in Ferroelectric Hf 0.5 Zr 0.5 O 2 Thin Films

Ferroelectric phase stability in hafnium oxide is reported to be influenced by factors that include composition, biaxial stress, crystallite size, and oxygen vacancies. In the present work, the ferroelectric performance of atomic layer deposited Hf 0.5 Zr 0.5 O 2 (HZO) prepared between TaN electrodes that are processed under conditions to induce variable biaxial stresses is evaluated. The post-processing stress states of the HZO films reveal no dependence on the as-deposited stress of the adjacent TaN electrodes. All HZO films maintain tensile biaxial stress following processing, the magnitude of which is not observed to strongly influence the polarization response. Subsequent composition measurements of stress-varied TaN electrodes reveal changes in stoichiometry related to the different preparation conditions. HZO films in contact with Ta-rich TaN electrodes exhibit higher remanent polarizations and increased ferroelectric phase fractions compared to those in contact with N-rich TaN electrodes. HZO films in contact with Ta-rich TaN electrodes also have higher oxygen vacancy concentrations, indicating that a chemical interaction between the TaN and HZO layers ultimately impacts the ferroelectric orthorhombic phase stability and polarization performance. The results of this work demonstrate a necessity to carefully consider the role of electrode processing and chemistry on performance of ferroelectric hafnia films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Compositional and phase dependence of elastic modulus of crystalline and amorphous Hf 1- x Zr x O 2 thin films

The elastic moduli of amorphous and crystalline atomic layer-deposited Hf 1-x Zr x O 2 (HZO, x = 0, 0.31, 0.46, 0.79, 1) films prepared with TaN electrodes on silicon substrates were investigated using picosecond acoustic measurements. The moduli of the amorphous films were observed to increase between 211 ± 6 GPa for pure HfO 2 and 302 ± 9 GPa for pure ZrO 2 . In the crystalline films, it was found that the moduli increased upon increasing the zirconium composition from 248 ± 6 GPa for monoclinic HfO 2 to 267 ± 9 GPa for tetragonal ZrO 2 . Positive deviations from this increase were observed for the Hf 0.69 Zr 0.31 O 2 and Hf 0.54 Zr 0.46 O 2 compositions, which were measured to have moduli of 264 ± 8 GPa and 274 ± 8 GPa, respectively. These two compositions contained the largest fractions of the ferroelectric orthorhombic phase, as assessed from polarization and diffraction data. The biaxial stress states of the crystalline films were characterized through sin 2 (ψ) x-ray diffraction analysis. The in-plane stresses were all found to be tensile and observed to increase with the increasing zirconium composition, between 2.54 ± 0.6 GPa for pure HfO 2 and 5.22 ± 0.5 GPa for pure ZrO 2 . The stresses are consistent with large thermal expansion mismatches between the HZO films and silicon substrates. Furthermore, these results demonstrate a device-scale means to quantify biaxial stress for investigation on its effect on the ferroelectric properties of hafnia-based materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Liquid–Solid Mixtures of Ga Metal Infused with Cu Microparticles and Nanoparticles for Microscale and Nanoscale Patterning of Solid Metals at Room Temperature

This paper demonstrates and characterizes a simple ink for nanopatterning of solid metallic structures under ambient conditions by taking advantage of the low melting point of gallium and its affinity to form intermetallics with other metals. Bare copper micro- and nanoparticles readily mix with liquid gallium near room temperature to form a paste that ultimately amalgamates into a dense solid when mixed at the appropriate concentration ratios. The paste has sufficient shelf life that can be extruded from a nozzle at modest temperatures to form solid three-dimensional (3D) shapes. Additionally, the paste can be molded at room temperature to replicate feature sizes ranging from a few millimeters down to hundreds of nanometers. In situ X-ray diffraction (XRD) and thermo-mechanical analysis (TMA) data show gallium and copper readily interdiffuse to form the thermodynamically expected intermetallic phase. We describe the capabilities and limitations of a simple way to pattern solid metals in an additive fashion (syringe-based extrusion) and with high resolution (molding) at or near room temperature. Here, the use of a paste that solidifies provides a novel route for 3D printing of solid metals at ambient temperatures as well as the creation of micro- and nanostructured metallic surfaces that may be useful for optics, non-wetting surfaces, or electronic microcomponents.

36 MATERIALS SCIENCE↗