Search NASA⌕ Search

Engineering topics

Fang, H.

Publications and source records attributed to Fang, H..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Characterization of free-standing InAs quantum membranes by standing wave hard x-ray photoemission spectroscopy

Free-standing nanoribbons of InAs quantum membranes (QMs) transferred onto a (Si/Mo) multilayer mirror substrate are characterized by hard x-ray photoemission spectroscopy (HXPS) and by standing-wave HXPS (SW-HXPS). Information on the chemical composition and on the chemical states of the elements within the nanoribbons was obtained by HXPS and on the quantitative depth profiles by SW-HXPS. By comparing the experimental SW-HXPS rocking curves to x-ray optical calculations, the chemical depth profile of the InAs(QM) and its interfaces were quantitatively derived with ångström precision. We determined that (i) the exposure to air induced the formation of an InAsO 4 layer on top of the stoichiometric InAs(QM); (ii) the top interface between the air-side InAsO 4 and the InAs(QM) is not sharp, indicating that interdiffusion occurs between these two layers; (iii) the bottom interface between the InAs(QM) and the native oxide SiO 2 on top of the (Si/Mo) substrate is abrupt. In addition, the valence band offset (VBO) between the InAs(QM) and the SiO 2 /(Si/Mo) substrate was determined by HXPS. The value of VBO = 0.2 ± 0.04 eV is in good agreement with literature results obtained by electrical characterization, giving a clear indication of the formation of a well-defined and abrupt InAs/SiO 2 heterojunction. We have demonstrated that HXPS and SW-HXPS are non-destructive, powerful methods for characterizing interfaces and for providing chemical depth profiles of nanostructures, quantum membranes, and 2D layered materials.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Observation of a hole-size-dependent energy shift of the surface-plasmon resonance in Ni antidot thin films

A combined experimental and theoretical study of the magneto-optic properties of a series of nickel antidot thin films is presented. The hole diameter varies from 869 down to 636 nm, while the lattice periodicity is fixed at 920 nm. This results in an overall increase of the polar Kerr rotation with decreasing hole diameter due to the increasing surface coverage with nickel. In addition, at photon energies of 2.7 and 3.3 eV, where surface-plasmon excitations are expected, we observe distinct features in the polar Kerr rotation not present in continuous nickel films. The spectral position of the peaks exhibits a red shift with decreasing hole size. This is explained within the context of an effective medium theory by a change in the effective dielectric function of the Ni thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2011

A Cloud and Precipitation Radar System Concept for the ACE Mission

One of the instruments recommended for deployment on the Aerosol/Cloud/Ecosystems (ACE) mission is a new advanced cloud profiling radar. In this paper, we describe such a radar design, called ACERAD, which has 35- and 94-GHz channels, each having Doppler and dual-polarization capabilities. ACERAD will scan at Ka-band and will be nadir-looking at W-band. To get a swath of 25-30 km, considered the minimum useful for Ka-band, ACERAD needs to scan at least 2 degrees off nadir; this is at least 20 beamwidths, which is quite large for a typical parabolic reflector. This problem is being solved with a Dragonian design; a scaled prototype of the antenna is being fabricated and will be tested on an antenna range. ACERAD also uses a quasi-optical transmission line at W-band to connect the transmitter to the antenna and antenna to the receiver. A design for this has been completed and is being laboratory tested. This paper describes the current ACERAD design and status.

CloudSat Mission↗
NASA NTRS2011

A Nonlinear Dynamic Model and Free Vibration Analysis of Deployable Mesh Reflectors

This paper presents a dynamic model of deployable mesh reflectors, in which geometric and material nonlinearities of such a space structure are fully described. Then, by linearization around an equilibrium configuration of the reflector structure, a linearized model is obtained. With this linearized model, the natural frequencies and mode shapes of a reflector can be computed. The nonlinear dynamic model of deployable mesh reflectors is verified by using commercial finite element software in numerical simulation. As shall be seen, the proposed nonlinear model is useful for shape (surface) control of deployable mesh reflectors under thermal loads.

mesh reflectors↗
NASA NTRS2011

Experimental Study of a Membrane Antenna Surface Adaptive Control System

Due to their ultra lightweight and high packaging efficiency, membrane reflectors are getting more and more attentions for mission architectures that need extremely large inspace deployable antennas. However how to maintain the surface shape of a membrane reflector to the instrument precision requirements is a very challenging problem. This experimental study investigated using PVDF membrane piezoelectric material as actuators to control the surface figures of membrane reflectors. The feasibility of this approach is demonstrated by several sets of test results.

packaging↗
NASA NTRS2011

Coupled Elastic-Thermal Dynamics of Deployable Mesh Reflectors

This paper presents a coupled elastic-thermal dynamic model and a quasi-static strategy on the analysis of the reflector dynamics in the space mission. The linearized model, its natural frequencies and mode shapes are then derived upon the nonlinear static equilibrium of the structure. The numerical example is provided to fully adapt the strategy and investigate the dynamic behaviors of the structure. Finally the proposed method is applied on the sample of the deployable mesh reflector and the simulation results are presented. The research work delivered in the paper will be used to design the feedback surface in future.

fixed boundaries↗
NASA NTRS2010

Thermal Deformation and RF Performance Analyses for the SWOT Large Deployable Ka-Band Reflectarray

A large deployable antenna technology for the NASA Surface Water and Ocean Topography (SWOT) Mission is currently being developed by JPL in response to NRC Earth Science Tier 2 Decadal Survey recommendations. This technology is required to enable the SWOT mission due to the fact that no currently available antenna is capable of meeting SWOT's demanding Ka-Band remote sensing requirements. One of the key aspects of this antenna development is to minimize the effect of the on-orbit thermal distortion to the antenna RF performance. An analysis process which includes: 1) the on-orbit thermal analysis to obtain the temperature distribution; 2) structural deformation analysis to get the geometry of the antenna surface; and 3) the RF performance with the given deformed antenna surface has been developed to accommodate the development of this antenna technology. The detailed analysis process and some analysis results will be presented and discussed by this paper.

thermal distorsion↗
NASA NTRS2003

Thermal distortion analyses of a three-meter inflatable reflectarray antenna

Gossamer space structures are relatively large, flimsy, and lightweight. As a result, they are more easily affected or degraded by space thermal environments compared to other space structures. This study examines the structural integrity of a three-meeter Ka-band inltable/self-rigidizable reflectarray antenna under space thermal environments.

thermal inflatable temperature buckling boom anten↗
NASA NTRS2003

Deployment study of a self-rigidizable inflatable boom

Deployment dynamic behavior of an inflatable space structure is analyzed using a combination of gas dynamic analysis and rigid body kinematics simulations. Modeling technique is presented for deployment of a simple cantilever boom that is rolled up on a cylindrical mandrel.

inflatable boom deployment dynamics vibration kina↗
NASA NTRS2002

Development of inflatable antenna structures

Self-rigidizable spring-tape-reinforced (STR) booms were used to develop structural systems for large-aperture space inflatable radar antennas. The lightweight planar frames built with STR booms can be compactly stowed for launch, deployed by inflation pressure in space, and used to tension the RF membrane apertures of the antennas. Engineering models of a Ka-band reflectarray antenna and a L-band synthetic-aperture radar antenna were developed and have successfully demonstrated stowage and deployment, as well as RF performance. A design improvement was also being implemented to enhance long-term configuration stability and widen the application range of the STR booms.

inflatable antenna structures deployment↗
NASA NTRS2002

Development of a three-meter Ka-band reflectarray antenna

With the development of inflatable technologies, inflatable structures used as large space antennas are becoming very possible for near term space missions. This paper discusses the development of an inflatable/self-rigidizable structure for a three-meter Ka-band reflectarray antenna.

inflatable gossamer reflectarray antenna self rigi↗
NASA NTRS2001

Development of an innovative space boom

presents the development of a new type of ultra-lightweight space boom, called the self-deployable Spring Strip Boom or simply the S cubed boom. It describes the fundamental design concept and several variations of design configurations. Test results of proof of concept models are discussed and compared with results obtained by analytical simultations.

development space boom inflatable rigidizable↗