Engineering topics

Farhad Ghaffari

Publications and source records attributed to Farhad Ghaffari.

28 records · Page 2

NASA NTRS1989

A Patched-Grid Algorithm for Complex Configurations Directed Towards the F/A-18 Aircraft

A patched-grid algorithm for the analysis of complex configurations with an implicit, upwind-biased Navier-Stokes solver is presented. Results from both a spatial-flux and a time-flux conservation approach to patching across zonal boundaries are presented. A generalized coordinate transformation with a biquadratic geometric element is used at the zonal interface in order to treat highly stretched viscous grids and arbitrarily-shaped zonal boundaries. Applications are made to the F-18 forebody-strake configuration at subsonic, high-alpha conditions. Computed surface flow patterns compare well with ground-based and flight-test results; the large effect of Reynolds number on the forebody flow-field is shown.

High alpha research vehicle↗

NASA NTRS1989

Navier-Stokes Solutions about the F/A-18 Forebody-LEX Configuration

Three-dimensional viscous flow computations are presented for the F/A-18 forebody-LEX geometry. Solutions are obtained from an algorithm for the compressible Navier-Stokes equations which incorporates an upwind-biased, flux-difference-splitting approach along with longitudinally-patched grids. Results are presented for both laminar and fully turbulent flow assumptions and include correlations with wind tunnel as well as flight-test results. A good quantitative agreement for the forebody surface pressure distribution is achieved between the turbulent computations and wind tunnel measurements at Mach number of 0.6. The computed turbulent surface flow patterns on the forebody qualitatively agree well with in-flight surface flow patterns obtained on an F/A-fS aircraft at Mach number of 0.34.

Transitional flow↗

NASA NTRS1988

An analytical method for the ditching analysis of an airborne vehicle

A simple analytical method has been introduced for aerohydrodynamic load analysis of an airborne configuration during water ditching. The method employs an aerodynamic panel code, based on linear potential flow theory, to simulate the flow of air and water around an aircraft configuration. The free surface separating the air and water region is represented by doublet sheet singularities. Although all the theoretical load distributions are computed for air, provisions are made to correct the pressure coefficients obtained on the configuration wetted surfaces to account for the water density. As an analytical tool, the Vortex Separation Aerodynamic (VSAERO) code is chosen to carry out the present investigation. After assessing the validity of the method, its first application is to analyze the water ditching of the Space Shuttle configuration at a 12 degree attitude.

Pressure coefficient↗

NASA NTRS1988

An analytical method for ditching analysis of an airborne vehicle

Linear potential flow↗

NASA NTRS1986

PAN AIR application to the F-106B

The PAN AIR computer code was employed in the present study to investigate the aerodynamic effects of the various geometrical changes and flow conditions on a configuration similar to the F-106B half-airplane tested in the Langley 30x60-foot wind tunnel. The various geometries studied included two forebodies (original and shortened), two inlet flow conditions (open and closed) two vortex flap situations (off and on). The attached flow theoretical solutions were obtained for Mach number of 0.08 and angle of attack of 8 deg., 10 deg., 12 deg., and 14 deg. In general this investigation revealed that the shortening of the forebody or closing of the inlet produced only a small change in the overall aerodynamic coefficients of the basic F-106B configuration throughout the examined angles of attack. However, closing the inlet of the configuration resulted in a slightly higher drag level at low angles of attack. Furthermore, at and above 10 deg. angle of attack, it was shown that the presence of the vortex flap causes an increase in the total lift and drag. Also, these theoretical results showed the expected reduction in longitudinal stability level with addition of the vortex flap to the basic F-106B configuration.

Farhad Ghaffari↗

NASA NTRS1985

An Attached Flow Design of a Noninterferring Leading Edge Extension to a Thick Delta Wing

An analytical procedure for the determination of the shape of a Leading-Edge Extension (LEE) which satisfies design criteria, including especially noninterference at the wing design point, has been developed for thick delta wings. The LEE device best satisfying all criteria is designed to be mounted on a wing along a dividing stream surface associated with an attached flow design lift coefficient (C L,d ) of greater than zero. This device is intended to improve the aerodynamic performance of transonic aircraft at C L greater than C L,d system emanating from the LEE leading edge. In order to quantify this process a twisted and cambered thick delta wing was chosen for the initial application of this design procedure. Appropriate computer codes representing potential and vortex flows were employed to determine the dividing stream surface at C L,d and an optimized LEE planform shape at C L greater than C L,d , respectively. To aid in the LEE selection, the aerodynamic effectiveness of 36 planforms was investigated at C L greater than C L,d . This study showed that reducing the span of the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, regardless of the shape or area. Furthermore, for a fixed area, constant-chord LEE candidates were relatively more efficient than those with sweep less than the wing. At C L,d , the presence of the LEE planform best satisfying the design criteria was found to have no effect on the wing alone aerodynamic performance.

Leading edge extension↗

NASA NTRS1984

An analytical design procedure for the determination of effective leading edge extensions on thick delta wings

An analytical design procedure for leading edge extensions (LEE) was developed for thick delta wings. This LEE device is designed to be mounted to a wing along the pseudo-stagnation stream surface associated with the attached flow design lift coefficient of greater than zero. The intended purpose of this device is to improve the aerodynamic performance of high subsonic and low supersonic aircraft at incidences above that of attached flow design lift coefficient, by using a vortex system emanating along the leading edges of the device. The low pressure associated with these vortices would act on the LEE upper surface and the forward facing area at the wing leading edges, providing an additional lift and effective leading edge thrust recovery. The first application of this technique was to a thick, round edged, twisted and cambered wing of approximately triangular planform having a sweep of 58 deg and aspect ratio of 2.30. The panel aerodynamics and vortex lattice method with suction analogy computer codes were employed to determine the pseudo-stagnation stream surface and an optimized LEE planform shape.

Farhad Ghaffari↗

NASA NTRS1984

An investigation of aerodynamic characteristics of wings having vortex flow using different numerical codes

Three different numerical codes are employed to determine the aerodynamic characteristics of wings with separation induced vortex flows. Both flat as well as cambered wings of various planform shapes are studied. The effects of wing thickness, fuselage, notch ratio and multiple vortex modeling on aerodynamic performance of the wing are also examined. The theoretically predicted results are compared with experimental results to validate the various computer codes used in this study. An analytical procedure for designing aerodynamically effective leading edge extension (LEE) for a thick delta wing is also presented.

Sushil K Chaturvedi↗

NASA NTRS1982

Study of highly sweptback wings by the free vortex sheet method

The aerodynamic characteristics of highly sweptback wings with separations induced vortex flows have been numerically investigated using the free vortex sheet method, developed by Boeing Company, under a contract with NASA/Langley Research Center. The models studied included delta and straked wings, and wings with leading edge extensions. Also, PAN-AIR code has been used to design a fixed leading edge extension into a thick delta wing. The theoretical results predicted have been compared with the experimental data wherever available, and the code capabilities and limitations explored. New fuselage effects also have been considered in some cases.

C Subba Reddy↗

NASA NTRSDate not supplied

An Overview of NASA Langley Low-Speed CFD Contributions to the Space Launch System Program

In this review paper, low-speed computational work from NASA Langley in support of the Space Launch System (SLS) is discussed. This information includes both historic and present efforts with the Kestrel CFD solver. The low-speed aerodynamics of SLS is highly complex and analysis of the unsteady flowfield requires significant computational efforts. The SLS mission profile varies from the vehicle static on the launch pad through high-speed ascent, and this paper focuses on the prelaunch as well as liftoff and transition portions of the flight both in proximity to the launch tower and in isolation. High-alpha conditions, as large as 90~deg, result in a flowfield dominated by massive, large-scale flow separation and asymmetric vortices. High-fidelity solutions require an unsteady computational formulation to accurately capture the aerodynamics of the vehicle. A detailed discussion of the computational approach is presented, followed by key efforts to support the program.

Brent W Pomeroy↗