Search NASA⌕ Search

Engineering topics

Fear, J. S.

Publications and source records attributed to Fear, J. S..

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

NASA/GE advanced low emissions combustor program

The Advanced Low Emissions Combustor Program consisted of the design and testing of advanced combustor concepts utilizing lean, premixed, prevaporized fuel and variable geometry. The objective was to evaluate the potential of these combustor systems to provide very low pollutant emissions levels, superior performance and high durability relative to contemporary combustor designs. Four full annular combustor concepts were designed and fabricated for a 30:1 pressure ratio high bypass turbofan engine. The four full annular combustors with active variable geometry were tested at pressures up to approximately 0.7 MPa with Jet A fuel. The two most promising concepts were also tested in a high pressure sector combustor test rig capable of operation at the maximum engine pressures. The high pressure sector combustor tests were conducted with Jet A and a fuel with reduced hydrogen content. Results of the sector combustor tests are presented in this paper. The potential for very low emissions with premixed fuel was demonstrated. However, autoignition or flashback within the premixing systems was encountered at high pressures. Further development effort is required to address this problem area.

Ekstedt, E. E.↗
NASA NTRS1987

A variable geometry combustor for broadened properties fuels

A program was conducted to design and develop a variable geometry combustor, sized for the cycle and envelope of a large commercial turbofan engine. The combustor uses a variable area swirl cup to control stoichiometry in the primary combustion zone. Potential advantages of this design include improved capability to burn non-standard fuels, short system length, and increased operating temperature range for advanced high performance engine cycles. After considerable development, key program emissons and performance goals were met with the variable geometry combustor. Primary development efforts were to evolve improved variable swirl cup configurations. In particular, air leakage through the variable area swirl cup had a strong effect on low power emissions and performance, while smoke level at high power was affected by features for improved mixing of the fuel and swirler air flow. Additional design and development is still needed to evolve a practical variable geometry combustor.

Dodds, W. J.↗
NASA NTRS1984

NASA broad-specification fuels combustion technology program

The NASA Broad-Specification Fuels Combustion Technology Program was initiated in response to concerns that the supply of high-quality petroleum middle distillates for jet fuel, abundant in the past, would diminish in availability toward the end of the century. The specific program objective is to evolve the combustion system technology required to use fuels with moderate ranges of broadened properties in the engines used on commercial jet aircraft. The first phase of the program, in which effects of the use of broadened-properties fuels were identified and technology with the potential to offset these effects was also identified, has been completed. The second phase, in which the technology identified in Phase 1 is being refined, will be completed within the next three months.

Fear, J. S.↗
NASA NTRS1983

The NASA broad-specification fuels combustion technology program: An assessment of phase 1 test results

An assessment is made of the results of Phase 1 screening testing of current and advanced combustion system concepts using several broadened-properties fuels. The severity of each of several fuels-properties effects on combustor performance or liner life is discussed, as well as design techniques with the potential to offset these adverse effects. The selection of concepts to be pursued in Phase 2 refinement testing is described. This selection takes into account the relative costs and complexities of the concepts, the current outlook on pollutant emissions control, and practical operational problems.

Fear, J. S.↗
NASA NTRS1982

NASA Broad Specification Fuels Combustion Technology program - Pratt and Whitney Aircraft Phase I results and status

In connection with increases in the cost of fuels and the reduced availability of high quality petroleum crude, a modification of fuel specifications has been considered to allow acceptance of poorer quality fuels. To obtain the information upon which a selection of appropriate fuels for aircraft can be based, the Broad Specification Fuels Combustion Technology program was formulated by NASA. A description is presented of program-related investigations conducted by an American aerospace company. The specific objective of Phase I of this program has been to evaluate the impact of the use of broadened properties fuels on combustor design through comprehensive combustor rig testing. Attention is given to combustor concepts, experimental evaluation, results obtained with single stage combustors, the stage combustor concept, and the capability of a variable geometry combustor.

Lohmann, R. P.↗
NASA NTRS1982

NASA/General Electric broad-specification fuels combustion technology program - Phase I results and status

A program is being conducted to develop the technology required to utilize fuels with broadened properties in aircraft gas turbine engines. The first phase of this program consisted of the experimental evaluation of three different combustor concepts to determine their potential for meeting several specific emissions and performance goals, when operated on broadened property fuels. The three concepts were a single annular combustor; a double annular combustor; and a short single annular combustor with variable geometry. All of these concepts were sized for the General Electric CF6-80 engine. A total of 24 different configurations of these concepts were evaluated in a high pressure test facility, using four test fuels having hydrogen contents between 11.8 and 14%. Fuel effects on combustor performance, durability and emissions, and combustor design features to offset these effects were demonstrated.

Dodds, W. J.↗
NASA NTRS1980

NASA broadened-specification fuels combustion technology program

The broadened-Specification Fuels Combustion Technology program's purpose is to evolve and demonstrate the technology required to enable current and next generation high-thrust, high-bypass-ratio turbofan engines to use fuels with broadened properties and to verify the evolved technology in full scale engine tests. The three phases of the program are combustor concept screening, combustor optimization testing, and engine verification testing. Constraints for designing combustion systems are outlined and problems to be expected in the use of broadened properties fuels are listed.

Fear, J. S.↗
NASA NTRS1980

NASA Broad-Specification Fuels Combustion Technology Program - Status and description

The use of 'broad-specification' fuels in aircraft gas turbine engines can be a significant factor in offsetting anticipated shortages of current-specification jet fuel in the latter part of the century. The changes in fuel properties accompanying the use of broad-specification fuels will tend to cause numerous emissions, performance, and durability problems in currently-designed combustion systems. The NASA Broad-Specification Fuels Combustion Technology Program is a contracted effort to evolve and demonstrate the technology required to utilize broad-specification fuels in current and next generation commercial Conventional Takeoff and Landing (CTOL) aircraft engines, and to verify this technology in full-scale engine tests in 1983. The program consists of three phases: Combustor Concept Screening, Combustor Optimization Testing, and Engine Verification Testing.

Fear, J. S.↗
NASA NTRS1979

NASA broad-specification fuels combustion technology program: Status and description

The program presented is a contracted effort to evolve and demonstrate the technology required to utilize broad-specification fuels in current and next generation commercial Conventional Takeoff and Landing aircraft engines, and to verify this technology in full-scale engine tests in 1983. The program consists of three phases: Combustor Concept Screening, Combustor Optimization Testing, and Engine Verification Testing. The development and screening of the combustion system designs for the CF6-80 engine and the JT9D-7 engine, respectively, in high-pressure sector test rigs are reported.

Fear, J. S.↗
NASA NTRS1976

The NASA Pollution-Reduction Technology Program for small jet aircraft engines - A status report

A three-phase experimental program is described which has the objective of enabling EPA Class T1 jet engines to meet the 1979 EPA emissions standards. In Phase I, three advanced combustor concepts, designed for the AiResearch TFE 731-2 turbofan engine, were evaluated in screening tests. Goals for carbon monoxide and unburned hydrocarbons were met or closely approached with two of the concepts with relatively modest departures from conventional combustor design practices. A more advanced premixing/prevaporizing combustor, while appearing to have the potential for meeting the oxides of nitrogen goal as well, will require extensive development to make it a practical combustion system. Smoke numbers for the two combustor concepts which will be carried forward into Phase II of the program were well within the EPA smoke standard. Phase II, Combustor-Engine Compatibility Testing, which is in its early stages, and planned Phase III, Combustor-Engine Demonstration Testing, are also described.

Fear, J. S.↗
NASA NTRS1976

The NASA pollution-reduction technology program for small jet aircraft engines

Three advanced combustor concepts, designed for the AiResearch TFE 731-2 turbofan engine, were evaluated in screening tests. Goals for carbon monoxide and unburned hydrocarbons were met or closely approached with two of the concepts with relatively modest departures from conventional combustor design practices. A more advanced premixing/prevaporizing combustor, while appearing to have the potential for meeting the oxides of nitrogen goal as well, will require extensive development to make it a practical combustion system. Smoke numbers for the two combustor concepts were well within the EPA smoke standard. Phase 2, Combustor-Engine Compatibility Testing, which is in its early stages, and planned Phase 3, Combustor-Engine Demonstration Testing, are also described.

Fear, J. S.↗
NASA NTRS1973

Performance of an annual combustor designed for a low-cost turbojet engine

Performance tests were conducted on a combustor designed for use in a low-cost turbojet engine. Low-cost features included the use of very inexpensive simplex fuel nozzles and combustor liners of perforated sheet material. Combustion efficiencies at the altitude-cruise and sea-level design points were approximately 94 and 96 percent, respectively. The combustor isothermal total-pressure loss was 8.8 percent at the altitude-cruise-condition diffuser-inlet Mach number of 0.335. The combustor-exit temperature pattern factor was less than 0.3 at the altitude-cruise, sea-level-cruise, and sea-level-static design conditions. The combustor-exit average radial temperature profiles at all conditions were in very good agreement with the design profile. The intense mixing required because of the very high combustor heat-release rate had an adverse effect on ignition capability at altitude windmilling design conditions.

Fear, J. S.↗
NASA NTRS1972

Performance of a small annular turbojet combustor designed for low cost

Performance investigations were conducted on a combustor utilizing several cost-reducing innovations and designed for use in a low-cost 4448-N thrust turbojet engine for commercial light aircraft. Low-cost features included simple, air-atomizing fuel injectors; combustor liners of perforated sheet; and the use of inexpensive type 304 stainless-steel material. Combustion efficiencies at the cruise and sea-level-takeoff design points were approximately 97 and 98 percent, respectively. The combustor isothermal pressure loss was 6.3 percent at the cruise-condition diffuser inlet Mach number of 0.34. The combustor exit temperature pattern factor was less than 0.24 at both the cruise and sea-level-takeoff design points. The combustor exit average radial temperature profiles at all conditions were in very good agreement with the design profile.

Fear, J. S.↗