Search NASA⌕ Search

Engineering topics

Fedotov, A.

Publications and source records attributed to Fedotov, A..

Beam Dynamics of the Strong Hadron Cooler ERL at the Electron-Ion Collider

The Strong Hadron Cooler Energy Recovery Linac (SHC-ERL) for the Electron-Ion Collider (EIC) is required to produce an electron beam with a bunch charge of 1 nC, an average current of 100 mA, and a beam energy of both 150 and 55 MeV, with strict requirements for the transverse emittance, slice energy spread, and longitudinal distribution. This paper covers the design in detail, including preliminary considerations of higher order effects and diagnostics.

Deitrick, K.↗

Design Overview of the Strong Hadron Cooler ERL at the Electron-Ion Collider

The Electron-Ion Collider (EIC) is currently under development to be built at Brookhaven National Lab and requires cooling during collisions in order to preserve the quality of the hadron beam despite degradation due to intra-beam scattering and beam-beam effect. An Energy Recovery Linac (ERL) is being designed to deliver the necessary electron beam for Coherent electron Cooling (CeC) of the hadron beam, with an electron bunch charge of 1 nC and an average current of 100 mA; two modes of operation are being developed for 150 and 55 MeV electrons, corresponding to 275 and 100 GeV protons. The injector of this Strong Hadron Cooler ERL (SHC-ERL) is shared with the Injection Cooler ERL, which cools lower energy proton beams via bunched beam cooling, as used in the Low Energy RHIC electron Cooling (LEReC). This talk introduces the layout and presents a high-level overview of the design.

Deitrick, K.↗

Measurement of the 1-jettiness event shape observable in deep-inelastic electron-proton scattering at HERA

The H1 Collaboration reports the first measurement of the 1-jettiness event shape observable $τ^b_1$ in neutral-current deep-inelastic electron-proton scattering (DIS). The observable $τ^b_1$ is equivalent to a thrust observable defined in the Breit frame. The data sample was collected at the HERA ep collider in the years 2003–2007 with center-of-mass energy of $\sqrt{s}$ = 319 GeV, corresponding to an integrated luminosity of 351.1 pb -1 . Triple differential cross sections are provided as a function of $τ^b_1$, event virtuality $Q^2$, and inelasticity y, in the kinematic region $Q^2$ > 150 GeV 2 . Single differential cross section are provided as a function of $τ^b_1$ in a limited kinematic range. Double differential cross sections are measured, in contrast, integrated over $τ^b_1$ and represent the inclusive neutral-current DIS cross section measured as a function of $Q^2$ and y. The data are compared to a variety of predictions and include classical and modern Monte Carlo event generators, predictions in fixed-order perturbative QCD where calculations up to $\mathcal{O}$($α^3_s$) are available for $τ^b_1$ or inclusive DIS, and resummed predictions at next-to-leading logarithmic accuracy matched to fixed order predictions at $\mathcal{O}$($α^2_s$). These comparisons reveal sensitivity of the 1-jettiness observable to QCD parton shower and resummation effects, as well as the modeling of hadronization and fragmentation. Within their range of validity, the fixed-order predictions provide a good description of the data. Monte Carlo event generators are predictive over the full measured range and hence their underlying models and parameters can be constrained by comparing to the presented data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Measurement of groomed event shape observables in deep-inelastic electron-proton scattering at HERA

The H1 Collaboration at HERA reports the first measurement of groomed event shape observables in deep inelastic electron-proton scattering (DIS) at $\sqrt{s} =319$ GeV, using data recorded between the years 2003 and 2007 with an integrated luminosity of 351 pb -1 . Event shapes provide incisive probes of perturbative and non-perturbative QCD. Grooming techniques have been used for jet measurements in hadronic collisions; this paper presents the first application of grooming to DIS data. The analysis is carried out in the Breit frame, utilizing the novel Centauro jet clustering algorithm that is designed for DIS event topologies. Events are required to have squared momentum-transfer $Q^2 > 150$ GeV 2 and inelasticity $0.2< y < 0.7$. We report measurements of the production cross section of groomed event 1-jettiness and groomed invariant mass for several choices of grooming parameter. Monte Carlo model calculations and analytic calculations based on Soft Collinear Effective Theory are compared to the measurements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Observation and differential cross section measurement of neutral current DIS events with an empty hemisphere in the Breit frame

The Breit frame provides a natural frame to analyze lepton–proton scattering events. In this reference frame, the parton model hard interactions between a quark and an exchanged boson defines the coordinate system such that the struck quark is back-scattered along the virtual photon momentum direction. In Quantum Chromodynamics (QCD), higher order perturbative or non-perturbative effects can change this picture drastically. As Bjorken-x decreases below one half, a rather peculiar event signature is predicted with increasing probability, where no radiation is present in one of the two Breit-frame hemispheres and all emissions are to be found in the other hemisphere. At higher orders in $\alpha$ s or in the presence of soft QCD effects, predictions of the rate of these events are far from trivial, and that motivates measurements with real data. We report on the first observation of the empty current hemisphere events in electron–proton collisions at the HERA collider using data recorded with the H1 detector at a center-of-mass energy of 319 GeV. The fraction of inclusive neutral-current DIS events with an empty hemisphere is found to be 0.0112 ± 3.9% stat ± 4.5% syst ± 1.6% mod in the selected kinematic region of 150 < Q 2 < 1500 GeV 2 and inelasticity 0.14 < y < 0.7. The data sample corresponds to an integrated luminosity of 351.1 pb -1 , sufficient to enable differential cross section measurements of these events. The results show an enhanced discriminating power at lower Bjorken-x among different Monte Carlo event generator predictions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The EIC accelerator: design highlights and project status

The design of the electron-ion collider (EIC) at Brookhaven National Laboratory is well underway, aiming at a peak electron-proton luminosity of 10e+34 cm^-1·sec^-1. This high luminosity, the wide center-of-mass energy range from 29 to 141 GeV (e-p) and the high level of polarization require innovative solutions to maximize the performance of the machine, which makes the EIC one of the most challenging accelerator projects to date. The complexity of the EIC will be discussed, and the project status and plans will be presented.

43 PARTICLE ACCELERATORS↗

Optical Properties of Wigglers for EIC Ring Electron Cooler

Electron Ion Collider (EIC) requires cooling of protons at top energy (275 GeV) to achieve the average design luminosity. Such a cooler must be capable of counteracting an IBS-driven emittance growth in proton bunches. The Ring Electron Cooler (REC) is a candidate for the EIC top energy cooler. The REC is a non-magnetized RF-based 150 MeV electron cooler, in which electrons are kept in the storage ring and re-utilized for several million turns. The REC is equipped with 18 damping wigglers, which keep electrons’ emittance constant by counteracting both electrons’ IBS and a proton electron beam-beam scattering happening in the cooling section. These wigglers operate at a relatively low energy but must have a rather high field to provide the required radiation cooling of electrons. As a result of this unique range of parameters, the wigglers’ optics exhibits interesting features The actual design parameters of the wigglers will be finalized in the REC lattice optimization.

43 PARTICLE ACCELERATORS↗

Development of an ERL for Coherent Electron Cooling at the Electron-Ion Collider

The Electron-Ion Collider (EIC) is currently under development to be built at Brookhaven National Lab and requires cooling during collisions in order to mitigate the hadron beam emittance degradation due to intra-beam scattering and beam-beam effects. An Energy Recovery Linac (ERL) is being designed to deliver the necessary electron beam for Coherent electron Cooling (CeC) of the hadron beam, with an electron bunch charge of 1 nC and an average current of 100 mA; two modes of operation are being developed for 150 and 55 MeV electrons, corresponding to 275 and 100 GeV protons. The injector of this Strong Hadron Cooler ERL (SHC-ERL) is shared with the Pre-cooler ERL, which cools lower energy proton beams via bunched beam cooling, as used in the Low Energy RHIC electron Cooling (LEReC). This paper reviews the current state of the design.

Deitrick, K.↗

DESIGN AND OPTIMIZATION OF AN ERL FOR COOLING EIC HADRON BEAMS

The baseline scheme for hadron beam cooling in the Electron Ion Collider (EIC) calls for Coherent electron Cooling (CeC) of the hadrons with non-magnetized electrons at high energy (150 MeV electrons) and additional cooling via conventional bunched beam cooling using a precooler system. The electron beam parameters for these concepts are at or beyond the current state of the art, with electron bunch charges on the order of 1 nC and average currents on the order of 100 mA and requiring an Energy Recovery Linac (ERL) to produce such beams. Using specifications provided by BNL and JLab, physicists and engineers at Xelera Research are working on a complete design of an ERL system capable of cooling EIC hadrons.

Gulliford, C.↗

Design of a ring cooler for electron ion collider with reverse bends

The high quality electron beam of a ring cooler for the electron ion collider requires strong radiation damping (and thus strong wigglers) to overcome both the intra-beam and the beam-beam scattering. In this paper we present an alternative design, where conventional bends with reversing and alternating directions between horizontal and vertical planes are implemented to satisfy the damping requirements.”

43 PARTICLE ACCELERATORS↗