Engineering topics

Feldhausen, Thomas A.

Publications and source records attributed to Feldhausen, Thomas A..

4 records

DOE OSTI2023

Multiscale characterization of an additively manufactured property graded Ni-base alloy for molten-salts\supercritical-CO 2 heat exchangers

The sequential optimization of strength and corrosion resistance in conventional alloy design procedures often results in a tradeoff between environmental degradation and optimal mechanical properties. A concurrent optimization of these two material properties is essential to efficiently develop high temperature alloys that can withstand harsh environments increasingly required for carbon–neutral energy technologies. In this work, we demonstrate the feasibility of directed energy deposition (DED) to manufacture a dual-corrosion resistant Ni-based alloy (Hastelloy N and Haynes 282), that meets the high temperature operation requirements of a molten-salts\supercritical-CO 2 (sCO 2 ) heat exchanger. A combination of multiscale characterization techniques and computational thermodynamics was employed to evaluate the cracking susceptibilities during fabrication and predict the microstructural stability of the material. Very good agreement was achieved between the observed and predicted phases and phase fractions of the as-printed material. A careful characterization of the transition zone between the two terminal alloy chemistries revealed potential precipitation strengthening (γ') on the Hastelloy N side while columnar-shaped M 23 C 6 and γ' precipitates that formed at grain boundaries (GBs) of the transition zone likely minimized the local interfacial energies. Both these mechanisms are believed to increase the interfacial stability but their performance at high temperatures requires further investigation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Downselection and Basic Properties of Additively Manufactured ODS Alloys

In the AMMT program the work package for development of new materials aimed to explore the advanced manufacturing techniques that are feasible for the manufacturing of advanced materials components. A merit-based feasibility study was attempted to identify an accelerated development path for dispersion strengthened (ODS) alloys by creatively combining additive manufacturing (AM) technologies with the recent advances in ODS materials and traditional manufacturing technologies. For the fiscal year, the primary tasks were focused to develop additive manufacturing (AM) and post-build processing route for oxide dispersion strengthened (ODS) ferritic (Fe-Cr alloy or 14YWT) and austenitic (Fe-Cr-Ni alloys or 316L and 316H) alloys and to perform basic microstructural and mechanical characterizations to provide feedbacks to the alloy and processing design. Further, the multi-laboratory effort created collaboratively a decision criteria matrix to evaluate and downselect the new materials processed by advanced manufacturing methods. This report is to describe the ODS alloy processing routes combining AM processes and post-build thermomechanical treatments, mechanical and microstructural characteristics of the newly developed materials, and the application results of the decision criteria matrix for the AM ODS alloys including a downselected material and feasible processing route. Key mechanical test results including tensile strength, tensile ductility, and fracture toughness data and are reported and explained. Higher strength was measured from the ferritic ODS alloys, while higher ductility and fracture toughness were measured from the austenitic ODS alloys. Many of the decision criteria were scored the same for the AM ferritic and austenitic ODS alloys, however, the generally known fact that the austenitic alloys have higher corrosion resistance and significantly better ductility. Although these scores are not significantly different to make them highly discernable, the austenitic ODS alloys were downselected to be the primary materials group in the future research on ODS materials in AMMT program.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effect of humidity of build chamber in hybrid manufacturing systems on part performance

Here hybrid manufacturing combines additive with subtractive machining operations which often require the use of a coolant, that can increase the humidity of the build chamber. The water vapor can be adsorbed on the powder surfaces and subsequently dissociate into hydrogen and oxygen during melting and can be absorbed by part during solidification. Here, we investigated the effect of build chamber humidity during hybrid manufacturing on the part quality on two most common classes of steels i.e., austenitic (316L) and ferritic (grade 91). We report that the humidity increase has a negligible effect on part performance of both classes of steels.

316L stainless steel↗

DOE OSTI2021

Initial Process Planning of a Hybrid Multi-Tasking Platform

Abstract Applications of hybrid technology are expanding from refurbishment and repair to low quantity, specialty part production, which are staple characteristics in medical implant, energy, and aerospace industry sectors, among others. This expansion has led to the development of the Mazak VC-500A/5X AM HWD, a wire fed laser cladding unit equipped with a standard 5 axis CNC. This unit is capable of building near net geometry of complex medium to large parts within a profitable timeframe, due to its comparatively high rate of deposition to that of a powder fed hybrid system. In this study, deposition and machining capabilities of the VC-500A/5X AM HWD are assessed through the production of three different test geometries by different process plans. Production of these test geometries is supported by an open loop sensor package primarily for monitoring machine health, data collection, and machine operator aid. The viability of extended deposition followed by machining is evaluated against a more cyclical strategy of reoccurring deposition and machining operations. Lastly, common defects in as-built geometries are evaluated and addressed through revisions to original process plans and toolpaths, indicating the need for continued innovation in hybrid manufacturing specific CAM/CAD software, as well as closed loop machine monitoring and quality control.

DeWitte, Lisa N.↗