Search NASA⌕ Search

Engineering topics

Fernandez-Zelaia, Patxi

Publications and source records attributed to Fernandez-Zelaia, Patxi.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Uncertainty Quantification of Fatigue Behavior of Rough AM Surfaces and Microstructures to Enable Hydrogen Gas Turbine

Modifying fossil-fueled industrial gas turbines to utilize low or zero-carbon fuels, such as hydrogen or hydrogen-natural gas blends, is a complex endeavor. The successful implementation of this technology hinges on three key design criteria: (1) developing new fuel injectors capable of efficiently burning alternative fuels, (2) ensuring manufacturability to meet cost and time-to-market goals, and (3) achieving component durability in the demanding environment of an operating gas turbine. Additive manufacturing (AM) accelerates product development, yet concerns persist regarding the durability of parts with rough AM surfaces. A fully experimental approach to quantify the fatigue performance of rough AM microstructures is both costly and labor-intensive. To address this, ORNL and Solar Turbines Incorporated (Solar) employed a crystal plasticity finite element (CPFE) model to identify the factors influencing AM surface fatigue behavior. These CPFE findings, combined with targeted experimental data, were used to develop a computationally efficient surrogate model suitable for assessing the lifespan of gas turbine engine components.

08 HYDROGEN↗
DOE OSTI2024

Using Additive Manufacturing to Repair Gas Turbine Hot Section Components

Ni-based superalloys are used in the hot sections of gas turbine engines due to their excellent high temperature performance. During service the material degrades due to exposure at high temperature and mechanical loads. Hence, utility provides often inspect, service, and repair components in gas turbine engines to ensure safe operation. A major challenge, however, is that the most heat-resistant alloys are generally considered ‘non-weldable’ rendering them difficult to repair via welding operations. In these cases components are often scrapped and then replaced by parts which must be re-manufactured. This burdens utilities with additional cost and supply chain issues can result in long term outages or reduced operating limtis. In this work EPRI and ORNL investigated a proposed repair strategy for gas turbine hot section components. Hot section superalloy GTD-111 was selected as a candidate repair material system and AM material ABD-900 the repair material. Sandwich structures were fabricated via electron beam melting additive manufacturing (EBM-AM) producing tensile bars with gage sections consisting of dissimilar ABD-900 / GTD-111 / ABD-900 material. Metallography revealed that the interface exhibited no deleterious phases or processing defeats. Creep rupture experiments on heat treated material demonstrates that the emulated repair coupons exhibit creep resistance between GTD-111 and ABD-900. This study demonstrates that the proposed EBM-AM repair strategy presents a viable opportunity towards enabling AM repair of gas turbine engine components.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Denoising diffusion probabilistic models for generative alloy design

Inverse material design is an extremely challenging optimization task made difficult by, in part, the highly nonlinear relationship linking performance with composition. Quantitative approaches have improved significantly owing to advances in high throughput experimentation and computational thermodynamics. However, existing physics-based tools are mostly forward models; input a chemistry and obtain a prediction. More recently the materials community has leveraged advances in the machine learning community to establish novel inverse design frameworks. Very recently denoising diffusion probabilistic models have been shown to be extremely powerful generators producing synthetic data of various modalities e.g. images, text, audio, tables, etc.. In this work a novel framework for alloy design and optimization is proposed leveraging these class of models. Five key generative tasks are demonstrated (1) unconditional generation (2) composition conditioned generation (3) property conditioned generation (4) multi-feedstock conditioned generation and (5) generative optimization. These methods were tested on three case studies: high entropy alloy design, superalloy binder jet additive manufacturing, and in-situ dual-feedstock wire-arc additive manufacturing. Results indicate that the established models are extremely flexible, expressive, and robust. The architecture’s flexibility and training procedure empower the model to learn complex intra-compositional and composition-property relationships. Furthermore, the probabilistic nature of these models makes them well suited for addressing solution non-uniqueness and tackling uncertainty quantification tasks. While the fidelity and quantity of the underlying training data is paramount, we envision that future alloy design frameworks will make extensive use of these kinds of machine learning models as “search” tools bolstering the utility of experimental and computational approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Using Additive Manufacturing to Repair Gas Turbine Hot Section Components

Ni-based superalloys are used in the hot sections of gas turbine engines due to their excellent high temperature performance. During service the material degrades due to exposure at high temperature and mechanical loads. Hence, utility provides often inspect, service, and repair components in gas turbine engines to ensure safe operation. A major challenge, however, is that the most heat-resistant alloys are generally considered ‘non-weldable’ rendering them difficult to repair via welding operations. In these cases components are often scrapped and then replaced by parts which must be re-manufactured. This burdens utilities with additional cost and supply chain issues can result in long term outages or reduced operating limits. In this work EPRI and ORNL investigated a proposed repair strategy for gas turbine hot section components. Hot section superalloy GTD-111 was selected as a candidate repair material system and AM material ABD-900 the repair material. Sandwich structures were fabricated via electron beam melting additive manufacturing (EBM-AM) producing tensile bars with gage sections consisting of dissimilar ABD-900 / GTD-111 / ABD-900 material. Metallography revealed that the interface exhibited no deleterious phases or processing defeats. Creep rupture experiments on heat treated material demonstrates that the emulated repair coupons exhibit creep resistance between GTD-111 and ABD-900. This study demonstrates that the proposed EBM-AM repair strategy presents a viable opportunity towards enabling AM repair of gas turbine engine components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Uncertainty Quantification of Fatigue Behavior of Rough AM Surfaces and Microstructures to Enable Hydrogen Gas Turbine Combustion

Modification of fossil-fueled industrial gas turbines to accept no/low carbon fuels (Hydrogen, H2/natural gas blends) is a significant undertaking. Successful deployment of this technology sits at the intersection of three design criteria (1) new functional fuel injectors that can burn these fuels, (2) manufacturability to meet cost and time-to-market targets, and (3) durability in the harsh environment of an operating turbine. Additive manufacturing (AM) provides accelerated product development. However, uncertainty remains around the durability of parts with rough AM surfaces. A fully experimental approach towards quantifying fatigue performance of rough AM microstructures is costly and laborious. Instead, Solar Turbines Incorporated (Solar) proposes the use of a crystal plasticity finite element (CPFE) model to quantify the factors that drive AM surface fatigue behavior. Solar will use the CPFE results, along with targeted experimental data, to train a computationally efficient surrogate model that can be incorporated into existing turbine part lifing methods.

08 HYDROGEN↗
DOE OSTI2024

Oak Ridge National Laboratory's Strategic Research and Development Insights for Digital Twins

Oak Ridge National Laboratory (ORNL) is pleased to provide our response to the NITRD RFI on Digital Twins Research and Development. Digital twins are virtual representations of physical systems, leveraging real-time data to simulate and predict behaviors. ORNL is advancing digital twin technology across various disciplines, including neutron scattering, networking, science ecosystems, supercomputing, secure facilities, mobility technologies, materials design and discovery, power systems, fusion reactors, biological sciences, and earth observation. These efforts aim to enhance scientific research, operational efficiency, and decision-making processes. ORNL facilities, such as the High Flux Isotope Reactor (HFIR), Grid-C, Spallation Neutron Source (SNS), and Oak Ridge Leadership Computing Facility (OLCF), provide the infrastructure to develop and demonstrate these digital twin technologies. In this document, we lay out key challenges, research gaps, and future opportunities based on our experience with digital twins that aim to serve as useful contributions towards a National Digital Twins R&D Strategic Plan. In the remaining document, we address nine of the thirteen topic areas specified in the RFI.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Novel Hot Gas Components for Gas Turbine Engines Enabled by Materials and Additive Manufacturing Process Development

Additive Manufacturing (AM), also known as 3D printing, has emerged as a manufacturing method that enables new design freedom for gas turbine engine manufacturers. However, the material selection for AM processable high-temperature super alloys is currently limited. Additionally, the heat transfer performance of AM enabled micro-cooling architectures is not yet well understood. Accordingly, in support of advanced manufacturing and engine performance development, Oak Ridge National Laboratory (ORNL)and Solar Turbines (Solar) conducted a multidisciplinary project to generate both AM super alloy material properties data and micro-channel performance data for two AM super alloys. The data supported the design and analysis of an internally cooled turbine hot section AM tip shoe component. This data was used to analytically predict the reduction in operating temperature of a gas turbine tip shoe. The work concluded that the cooling flow required to cool the tip shoe can be tuned to suit the efficiency improvements desired in an industrial gas turbine.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Gaussian Process-Based extended Goldak heat source model for finite element simulation of laser powder bed fusion additive manufacturing process

In this study, laser powder bed fusion (L-PBF) additive manufacturing (AM) is a key enabling technology to manufacture highly complex and integrated metallic structures. In L-PBF AM process, the melting of the metal powders and the layers underneath can be governed by either “conduction mode” or “keyhole mode”, with the keyhole mode reportedly leading to porosity and decreased strength and ductility by many studies. In part scale simulations, finite element (FE) model is often used to study the temperature distribution during printing and to predict the residual stress, where a volumetric heat flux with a Gaussian or a double ellipsoidal (Goldak) distribution is often applied as the laser heat source. However, the above heat source models can only capture the melt pool shape in the conduction mode, and fail to capture the transition to keyhole melting mode when the process parameters change. To overcome this inaccuracy, an extended Goldak heat source model is proposed by introducing a laser penetration term as a function of laser parameters obtained from a Gaussian-Process (GP) model. The model is validated by “2D pad” AlSi10Mg L-PBF experiments under a wide range of laser power, scan speed, and laser focus offset, and the results show the model successfully captures the measured melt pool shape in all conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Design of Novel Hot Gas Path Component for Gas Turbine Engines Enabled by Materials and Additive Manufacturing Process Development

This report covers the activities associated with the development and evaluation of two high-γ’ superalloys that were designed by external partners on this project, namely Carpenter Technologies Corporation and the University of California-Santa Barbra. One alloy was GammaPrint-700, a cobalt-base superalloy, and the other a nickel-base (Ni-base) superalloy GammaPrint-1100. Both were found to be printable through laser powder bed fusion (LPBF) additive manufacturing, with optimal process parameter sets being identified for each alloy. Further, high temperature mechanical testing was conducted on each alloy that showed both materials performed better than the comparative baseline (LPBF Hastelloy X), with the Ni-base superalloy being down-selected for scaling and printing of the tip shoe components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Considering interplay between multiple physical phenomena to elucidate single crystal-like texture, phase transformations, and mechanical behavior of directed energy deposited SS316L

A widespread implementation of large scale additive manufacturing (AM) processes, such as wire arc-directed energy deposition (WA-DED) AM can transform the current manufacturing supply chain networks. Naturally, such implementation requires control of the microstructural attributes, such as texture and phase evolution in the processed alloys. Currently, the texture evolution in fusion-based AM (F-BAM) processes is majorly rationalized by the phenomena occurring only during solidification. However, such rationalization is insufficient for understanding the evolution of primary and secondary crystallographic orientations, and consequently, fails to offer a comprehensive understanding and control of overall texture in F-BAM processed alloys. To this end, we report a single crystal (SX)-like texture in WA-DED processed SS316L for the first time. Furthermore, we assess the physical phenomena that may lead to such unique microstructural evolution during WA-DED AM. Subsequently, using microstructural characterization spanning the build height and thermomechanical simulations we investigate the effect of competitive growth and epitaxial growth occurring during solidification and thermally induced plastic deformation occurring post solidification on the overall texture of WA-DED processed SS316L. A spatial variation in solidification pathway is also established and correlated with variation in undercoolings across the build. Tensile tests revealed a strong orientation dependence of deformation mechanisms with over 110% elongation to failure of specimens deformed along <011>. Such anisotropy is rationalized using Schmid's analysis of dislocation slip and deformation twinning. Importantly, overall, the mechanisms outlined in this work will facilitate an enhanced understanding and subsequent control of texture evolution, solidification behavior and mechanical behavior of WA-DED processed steels.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Digital polycrystalline microstructure generation using diffusion probabilistic models

Accurate micromechanical simulation of polycrystalline materials requires a realistic digital representation of the grain scale microstructure. Here, this work demonstrates the use of a generative diffusion probabilistic model for synthesizing single phase polycrystalline realizations. The model performs well and is capable of producing realistic microstructures consisting of not just simple equiaxed structures but also structures exhibiting more complex spatial arrangements. Masked microstructure generation reveals that the model is context aware of morphological descriptors which may be encoded in the latent space. Training on more diverse data sets, with scaled up architectures, may enable development of future models capable of synthesizing even more complex microstructural features.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Self-supervised learning of spatiotemporal thermal signatures in additive manufacturing using reduced order physics models and transformers

Microstructure control via additive manufacturing has enormous potential as manufacturers, materials scientists, and designers alike seek to exploit novel fabrication technologies to improve component performance. Recent works have demonstrated the feasibility of producing materials with controlled microstructures across various length scales. However, the experimental approach towards exploring the process-structure space can be laborious and costly. This is particularly true if also considering scan pattern optimization which is well suited for processes such as powder bed fusion electron beam melting. In this work we propose an approach for encoding additive manufacturing layer-wise thermal response signatures using self-supervised representation learning. Thermal simulations from a reduced order model are utilized to estimate the spatiotemporal response during printing. A machine learning framework, using video-transformers, is utilized to efficiently distill spatiotemporal patterns into a compact latent space representation. This latent state representation encodes the relevant physics which is then utilized to establish a data-driven process-structure model for an additively manufactured Ni-based superalloy. In conclusion, the proposed methodology could potentially be used towards in-situ process monitoring, scan pattern experimental design, and component qualification.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Outlook on texture evolution in additively manufactured stainless steels: Prospects for hydrogen embrittlement resistance, overview of mechanical, and solidification behavior

Abstract Realizing application specific manufacture with fusion-based additive manufacturing (F-BAM) processes requires understanding of the physical phenomena that drive evolution of microstructural attributes, such as texture. Current approaches for understanding texture evolution in F-BAM are majorly considerate of the phenomena occurring only during solidification. This hinders the comprehensive understanding and control of texture during F-BAM. In this perspective article, we discuss several physical phenomena occurring during and after solidification that can determine texture in F-BAM processed stainless steels (SS). A crystal plasticity-coupled hydrogen adsorption-diffusion modeling framework is also leveraged to demonstrate the prospects of grain boundary engineering with F-BAM for enhanced hydrogen embrittlement resistance of SS. Implications of varying thermokinetics in F-BAM for solidification behavior of SS are discussed. Additionally, microstructural attributes that are key to high temperature mechanical performance of SS are highlighted. Considerations as outlined in this perspective article will enable grain boundary engineering and application specific microstructural design of SS with F-BAM. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rapid Alloy Selection and Additive Manufacturing of Nickel-Based Superalloys

In this work the rapid alloy selection and subsequent processability via additive manufacturing of nickelbased superalloys was investigated. Rapid alloy selection protocols developed within the project produced two viable nickel-based superalloys. This phase I CRADA demonstrates a viable route for selecting new nickel-based superalloys for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and high temperature properties of tungsten processed via electron beam melting additive manufacturing

There is considerable interest in the adoption of additive manufacturing for processing refractory metals. The layer-wise fabrication approach enables opportunities for producing complex geometries which cannot be otherwise be achieved via powder metallurgy. However, the processing science is still in its nascent stages and structure–property relations are relatively unexplored. Fundamental research is needed to further develop the technology and enable the fabrication of refractory metals for high temperature applications. Here we focus on the processing of pure tungsten using electron beam melting additive manufacturing. Experimentally we develop a suitable processing window for achieving high density crack free material. Microstructural analysis reveals that the microstructure generally consists of a columnar structure with a (111) build direction fiber preference, although, fiber switching was observed. Process induced deformation is believed to drive the formation of subgrains whose boundaries exhibit a high dislocation density. Additionally, high temperature tensile testing reveals that the material exhibits excellent properties closer to that of annealed tungsten. Significant mechanical anisotropy was observed to be present which is likely driven by strong crystallographic texture.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rapid Alloy Selection and Additive Manufacturing of Nickel Based Superalloys

In this work the rapid alloy selection and subsequent processability via additive manufacturing of nickelbased superalloys was investigated. Rapid alloy selection protocols developed within the project produced two viable nickel-based superalloys. This phase I CRADA demonstrates a viable route for selecting new nickel-based superalloys for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical Behavior of Additively Manufactured Molybdenum and Fabrication of Microtextured Composites

Refractory metals are a class of high-melting-temperature materials suitable for use in extreme environment applications. Interestingly, during additive manufacturing many pure refractory metals exhibit a switch from (001) to (111) build direction fiber preference with increasing surface energy density. Here we exploit this solidification physics to fabricate material with “mesoscale composite” engineered structures consisting of features with contrasting (001) and (111) build direction microtextures. Separately, elevated temperature tensile testing of EBM fabricated material with a randomized distribution of mixed (001)/(111)-fiber grains is shown to exhibit excellent properties. These results are utilized to build a crystal plasticity model for evaluating the local inelastic response of the composite mesoscale structures. Analysis of printed microstructures and microstructure-scale simulations indicate that both macro-scale and localized material behavior may be tailored. This strategy can be potentially used to synthesize materials with optimized performance for high-temperature applications.

36 MATERIALS SCIENCE↗