Search NASA⌕ Search

Engineering topics

Ferraro, N. M.

Publications and source records attributed to Ferraro, N. M..

At least 19 records

MHD-induced beta limits in the Large Helical Device

Using the extended-magnetohydrodynamics code, M3D-C1, we perform a systematic numerical study of the effect of externally applied heating on the achievable plasma beta in a ten field-period heliotron. Heat sources of varying intensity are applied to a vacuum magnetic field that is representative of the standard configuration of the Large Helical Device, with R 0 = 3.66 m, where R 0 is the radial position of the magnetic axis in vacuum. As the system is driven to a state that is unstable to low-n magnetohydrodynamic (MHD) modes, nonlinear mode interactions lead to the formation of chaotic magnetic fields. With sufficiently strong heating, a collapse of the electron temperature profile is observed. This demonstrates the necessity of simulating the self-consistent evolution of plasma profiles, without imposing assumptions on the structure of the magnetic field, to accurately determine transport properties in stellarator plasmas. It also highlights the value of these advanced simulation capabilities for accelerating the development of high-performance stellarator operating scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

FES 2023 Theory & Simulation Performance Target

The Report for the 2023 Theory & Simulation Performance Target (TSPT) is presented herein. The 1st, 2nd and 3rd Quarter Reports are given in Sec. I, Sec. II and Sec. III. These are unchanged from those previously submitted, except that in this final document the equations, figures and citations have been automatically renumbered. The 4th Quarter Report is given in Sec. IV. The following material presents verification calculations of several widely used three-dimensional (3D) magnetohydrodynamic (MHD) equilibrium codes in strongly shaped configurations; for both fixed and free-boundary equilibria; for the so-called vacuum case and for the case of high plasma pressure; and, for magnetic fields that have nested magnetic surfaces and for fields that have a magnetic island. The configurations studied includes the recently discovered “precise-QA” case [Phys. Rev. Lett., 128, 035001 (2002)] and other highly optimized configurations. Because of the strong (extreme) shaping, the latter of these pose challenges to the 3D MHD codes. A new method is introduced for constructing coordinates in arbitrarily shaped toroidal domains, and this can improve the robustness of 3D equilibrium calculations. Beyond the equilibrium calculation, this report demonstrates the capability of performing non-linear extended-MHD modelling of optimized stellarator equilibria. This capability allows the assessment not only of linear stability thresholds but also of the nonlinear evolution of unstable equilibria to new configurations that might be far from the original configuration, with significantly different transport properties and magnetic topology. They also enable the self-consistent determination of pressure profiles in non-integrable magnetic topology through the use of highly anisotropic thermal-transport equations. The calculations presented here represent the first demonstration of extended-MHD calculations in strongly-shaped, optimized quasi-symmetric configurations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the frequency bifurcations of the MHD startup modes in NSTX

The observed bifurcations of the low frequency (<50 kHz) and low toroidal periodicity (n < 5) magnetohydrodynamic (MHD) activity often present in the initial part of the National Spherical Tokamak Experiment (NSTX) discharges can be explained by the evolution of the radial profile of the safety factor (q=rB φ /RB θ ) crossing multiple rational surfaces in the core. Important performance limiting instability mechanisms in the NSTX spherical tokamak are often linked to low frequency and low-n MHD activity. They are quite common in long-pulse NSTX plasmas. They can be present at the beginning of the plasma current flat-top, at the end of the discharge or during the whole duration, and they have been observed to deleteriously impact performance over a wide range of q 95 . An interesting feature observed in some NSTX discharges is the presence of a bifurcation in the frequency of the low n modes, as low as n = 1, that have frequencies comparable to the plasma core rotation divided by n. Equilibrium reconstructions constrained by magnetic diagnostics data and motional stark effect pitch angle radial profiles suggest that the observed bifurcations are linked to a fast evolving minimum value of q. Finally, 3D non-linear resistive MHD simulations show that these modes are ideal and exist as non-resonant before the correspondent rational surface enters the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modelling the nonlinear plasma response to externally applied three-dimensional fields with the Stepped Pressure Equilibrium Code

Small-amplitude, symmetry-breaking magnetic field perturbations, including resonant magnetic perturbations (RMPs) and error fields, can profoundly impact plasma properties in both tokamaks and stellarators. In this work, we perform the first comparison between the Stepped Pressure Equilibrium Code (SPEC) (a comparatively fast and efficient equilibrium code based on energy-minimisation principles) and M3D-C 1 (a high-fidelity albeit computationally expensive initial-value extended-magnetohydro-dynamic (MHD) code) to assess the conditions under which SPEC can be used to model the nonlinear, non-ideal plasma response to an externally applied (m = 2,n = 1) RMP field in an experimentally relevant geometry. We find that SPEC is able to capture the plasma response in the weakly nonlinear regime – meaning perturbation amplitudes below the threshold for break up of the separatrix and onset of secondary magnetic island formation – when around half of the total toroidal flux is enclosed in the volume containing the q = 2 resonant surface. Further, the observed dependence of SPEC solutions on input parameters, including toroidal flux and the number of volumes into which the plasma is partitioned, indicates that additional exploration of the underlying Multi-Region Relaxed MHD physics model is needed to constrain the choice of parameters. Nonetheless, this work suggests promising applications of SPEC to optimisation and fusion plasma design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation of pellet ELM triggering in low-collisionality, ITER-like discharges

3D nonlinear, as well as 2D linear M3D-C1 simulations are used to model ELM triggering by small pellets in DIII-D discharges in the ITER relevant, peeling-limited pedestal stability regime. A critical pellet size threshold is found in both experiment and modeling depending on pedestal conditions, pellet velocity and injection direction. Using radial injection at the outboard midplane, the threshold is determined by M3D-C1 for multiple time slices of a DIII-D low-collisionality discharge that has pellet ELM triggering. Experimental observations show that a larger pellet size than the standard 1.3 mm diameter is necessary for ELM triggering; 1.8 mm pellets triggered several ELMs in cases where a smaller pellet failed. The M3D-C1 simulations are in good agreement with these observations. While the 2D linear simulations give insight into the change of growth rates for various toroidal modes with pellet size, the 3D nonlinear simulations apply a pellet ablation model that mimics the actual injection with good match to the experiment. The 3D nonlinear simulation confirms the pellet ELM triggering for a pellet size larger than the threshold found by the linear simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Approach to nonlinear magnetohydrodynamic simulations in stellarator geometry

The capability to model the nonlinear magnetohydrodynamic (MHD) evolution of stellarator plasmas is developed by extending the M3D-C 1 code to allow non-axisymmetric domain geometry. We introduce a set of logical coordinates, in which the computational domain is axisymmetric, to utilize the existing finite-element framework of M3D-C 1 . A C 1 coordinate mapping connects the logical domain to the non-axisymmetric physical domain, where we use the M3D-C 1 extended MHD models essentially without modifications. We present several numerical verifications on the implementation of this approach, including simulations of the heating, destabilization, and equilibration of a stellarator plasma with strongly anisotropic thermal conductivity, and of the relaxation of stellarator equilibria to integrable and non-integrable magnetic field configurations in realistic geometries.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Importance of resistivity on edge-localized mode onset in spherical tokamaks

In this work, we explore the impact of realistic plasma resistivity on the linear stability of peeling-ballooning (PB) modes in tokamak discharges with low-aspect ratio. For this study we consider discharges that are subject to edge-localized modes (ELMs) in the National Spherical Torus Experiment (NSTX). Employing the state of the art extended-magnetohydrodynamic (MHD) code M3D-C1 it is demonstrated that non-ideal effects can significantly affect PB stability thresholds in NSTX discharges. In particular, robust resistive PB modes are found to exist well before the ideal PB stability threshold is met. These novel results can explain why ideal-MHD theory often does not accurately describe ELM onset in spherical torus configurations, and also present a valuable basis for the development of a predictive model for ELMs in low-aspect ratio tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Computation of linear MHD instabilities with the multi-region relaxed MHD energy principle

Over the last decade, a variational principle based on a generalisation of Taylor's relaxation, referred to as multi-region relaxed magnetohydrodynamics (MRxMHDs) has been developed. The numerical solutions of the MRxMHD equilibria have been constructed using the Stepped Pressure Equilibrium Code (SPEC) (Hudson et al 2012 Phys. Plasmas 19 112502). In principle, SPEC could also be established to describe the MRxMHD stability of an equilibrium. In this work, a theoretical framework is developed to relate the second variation of the energy functional to the so-called Hessian matrix, enabling the prediction of MHD linear instabilities of cylindrical plasmas, and is implemented in SPEC. The negative and positive eigenvalues of the Hessian matrix predict the stability of an equilibrium. Verification studies of SPEC stability results with the M3D-C 1 code and the tearing mode $\Delta^{^{\prime}}$ criterion have been conducted for ideal and resistive MHD instabilities, respectively, in a pressureless cylindrical tokamak, and have shown good agreement. Overall, our stability analysis is a critical step towards understanding the MHD stability of three-dimensional MHDs where nested flux surfaces, magnetic islands and stochastic regions co-exist.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Predicting nonresonant pressure-driven MHD modes in equilibria with low magnetic shear

Nonresonant internal modes can be difficult to anticipate as there is no resonant surface in the plasma. However, equilibria that are unstable to multiple nonresonant magnetohydrodynamic (MHD) modes may be more prone to global loss of confinement since these instabilities generate spatially extended linear displacements, potentially enhancing magnetic field line chaos via nonlinear interactions. Here, we successfully predict the unstable nonresonant pressure-driven modes for equilibria with zero shear in the plasma core, irrational q on axis, and a central pressure gradient, which is consistent with pre-crash profiles in sawtoothing tokamak plasmas in the large-aspect-ratio limit. A criterion for identifying nonresonant modes most likely to be unstable is developed from the convergents of the continued fraction representation of q 0 . A higher-order analysis of the standard Energy Principle reveals the conditions under which these modes are expected to dominate. Linear growth rate spectra, as a function of toroidal mode number (up to n = 30), calculated using the initial-value extended-MHD code, M3D-C1, recover the characteristic dependence observed for ideal infernal modes. Nonresonant modes have also been invoked in some ideal sawtooth crash models. Finally, this work provides a mechanism to predict the mode numbers of infernal modes and, potentially, the width of some post-sawtooth-crash profiles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observations of heteroclinic bifurcations in resistive magnetohydrodynamic simulations of the plasma response to resonant magnetic perturbations

A class of topological magnetic island bifurcations that has not previously been observed in toroidal plasmas is described. Increasing an externally applied three-dimensional magnetic field in resistive magnetohydrodynamic simulations results in the asymmetric elongation of resonant island flux surfaces followed by a sequence of heteroclinic bifurcations. Here, these bifurcations produce new sets of hyperbolic-elliptic fixed points as predicted by the Poincaré-Birkoff fixed point theorem. Field line calculations verify that the new fixed points do not connect to those of the prebifurcated islands as required for heteroclinic bifurcations on a torus with winding numbers composed of common integer factors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Gyrokinetic understanding of the edge pedestal transport driven by resonant magnetic perturbations in a realistic divertor geometry

Self-consistent simulations of neoclassical and electrostatic turbulent transport in a DIII-D H-mode edge plasma under resonant magnetic perturbations (RMPs) have been performed using the global total-f gyrokinetic particle-in-cell code x-point gyrokinetic code (XGC), in order to study density pump-out and electron heat confinement. The RMP field is imported from the extended magneto-hydrodynamics code M3D-C1, taking into account the linear two-fluid plasma response. With both neoclassical and turbulence physics considered together, the XGC simulation reproduces two key features of experimentally observed edge transport under RMPs: increased radial particle transport in the pedestal region that is sufficient to account for the experimental pump-out rate and suppression of the electron heat flux in the steepest part of the edge pedestal. In the simulation, the density fluctuation amplitude of modes moving in the electron diamagnetic direction increases due to interaction with RMPs in the pedestal shoulder and outward, while the electron temperature fluctuation amplitude decreases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analysis of MHD stability and active mode control on KSTAR for high confinement, disruption-free plasma

Long-pulse plasma operation at high normalized beta, $β_N$, above the $\textit{n}$= 1 ideal MHD no-wall stability limit in KSTAR is presently limited by tearing instabilities rather than resistive wall modes. H-mode plasma operation during the recent KSTAR device campaign produced discharges having strong $\textit{m/n}$= 2/1 tearing instabilities at $β_N$ lower than the ideal MHD no-wall beta limit. The unstable tearing mode consequently reduced plasma confinement and toroidal plasma rotation significantly. We report the experiment confirmed that an extended duration of electron cyclotron heating (ECH) at the initial phase of the discharge plays a critical role in mode destabilization. To study destabilizing mechanisms that affect the mode growth, the stability of the observed tearing modes from plasmas with significantly different $β_N$ is computed by using the resistive DCON code and the M3D-C 1 code. Equilibrium reconstructions that include constraints from internal profile diagnostics, and computed fast particle pressure are used as input for reliable computation of stability. The classical tearing stability index, Δ', from resistive DCON is computed to be unstable when the island is fully saturated with large amplitude, while the unstable mode is not computed by M3D-C 1 . The modified Rutherford equation (MRE) describing the evolution of the island width has been constructed for KSTAR plasmas by using plasma parameters computed by the TRANSP code. The MRE model estimates a saturated island width corresponding to ~10% of the plasma minor radius for equilibrium at high $β_N$ 3 having a stable Δ' from the resistive DCON. In preparation for long-pulse plasma operation at higher beta utilizing increased plasma heating power, a resistive wall mode (RWM) active feedback control algorithm has been completed and enabled on KSTAR. To accurately determine the $\textit{n}$= 1component produced by RWMs, an algorithm has been developed that includes magnetic sensor compensation of the prompt applied field and the field from the induced current on the passive conductors. Use of multiple toroidal sensor arrays is enabled by modifying the sensor toroidal angles assumed in mode decomposition to include the effect of varied mode helicities in the outboard region where the mode measurement is made. This analysis on stability, transport, and control provides the required foundation for disruption prediction and avoidance research on KSTAR.

resistive wall mode (RWM)↗

Axisymmetric simulations of vertical displacement events in tokamaks: A benchmark of M3D-C 1 , NIMROD, and JOREK

A benchmark exercise for the modeling of vertical displacement events (VDEs) is presented and applied to the 3D nonlinear magnetohydrodynamic codes M3D-C 1 , JOREK, and NIMROD. The simulations are based on a vertically unstable NSTX equilibrium enclosed by an axisymmetric resistive wall with a rectangular cross section. A linear dependence of the linear VDE growth rates on the resistivity of the wall is recovered for sufficiently large wall conductivity and small temperatures in the open field line region. We report the benchmark results show good agreement between the VDE growth rates obtained from linear NIMROD and M3D-C 1 simulations and from the linear phase of axisymmetric nonlinear JOREK, NIMROD, and M3D-C 1 simulations. Axisymmetric nonlinear simulations of a full VDE performed with the three codes are compared, and an excellent agreement is found regarding the plasma location and plasma currents, as well as eddy and halo currents in the wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Vertical forces during vertical displacement events in an ITER plasma and the role of halo currents

Vertical displacement events (VDEs) can occur in elongated tokamaks causing large currents to flow in the vessel and other adjacent metallic structures. To better understand the potential magnitude of the associated forces and the role of the so called \halo currents" on them, we have used the M3D-C1 code to simulate potential VDEs in ITER. We used actual values for the vessel resistivity and prequench temperatures and, unlike most of the previous studies, the halo region is naturally formed by triggering the thermal quench with an increase in the plasma thermal conductivity. We used the 2D non-linear version of the code and vary the post-thermal quench thermal conductivity profile as well as the boundary temperature in order to generate a wide range of possible cases that could occur in the experiment. We also show that, for a similar condition, increasing the halo current does not increase the total force on the wall since it is offset by a decrease in the toroidal contribution.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Gyrokinetic study of collisional resonant magnetic perturbation (RMP)-driven plasma density and heat transport in tokamak edge plasma using a magnetohydrodynamic screened RMP field

The total-f gyrokinetic particle-in-cell code XGC is applied to study various aspects of collisional transport in the tokamak edge pedestal in the presence of resonant magnetic perturbations (RMPs) calculated with M3D-C1. Simulations including the separatrix and scrape-off layer are exercised for a model DIII-D H-mode plasma. Neutral particle recycling is modeled by means of ionization and charge exchange with the plasma. A fully nonlinear Fokker–Planck collision operator is utilized to account for non-Maxwellian edge plasma. Here, the study yields kinetic evidence that (i) neglecting the non-axisymmetric component of the RMP-generated electrostatic potential perturbation could yield a fictitiously high particle pump-out rate in the edge pedestal; that (ii) the experimental level of particle pump-out from the pedestal cannot be provided by collisional transport across Kolmogorov–Arnold–Moser surfaces except across the magnetic separatrix where stochastic magnetic field lines exist; that (iii) the H-mode type electron heat barrier is retained in the steep slope area under the M3D-C1 calculated RMPs; and that (iv) the stochastic electron heat-transport rate around the magnetic separatrix surface is much lower than the prediction by Rechester–Rosenbluth (1978 Phys. Rev. Lett. 40 38–41) and is qualitatively consistent with the experimentally observed rate. Detailed kinetic physics analysis on how the transport fluxes, electrostatic potential perturbation, and -well structure respond to onset of RMPs is also reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Error field impact on mode locking and divertor heat flux in NSTX-U

During the 2016 NSTX-U experimental campaign, locked modes in the plasma edge presented clear evidence of the presence of error fields. Extensive metrology and plasma response modeling with IPEC and M3D-C1 have been conducted to understand the various sources of error fields in NSTX-U as built in 2016, and to determine which of these sources have the greatest effect on the plasma. In particular, modeling finds that the error field from misalignment of the toroidal field (TF) coils may have a significant effect on the plasma. The response to the TF error field is shown to depend on the presence of a q = 1 surface, in qualitative agreement with experimental observations. It is found that certain characteristics of the TF error field present new challenges for error field correction. Specifically, the error field spectrum differs significantly from that of coils on the low-field side (such as the NSTX-U error field correction coils), and does not resonate strongly with the dominant kink mode, thus potentially requiring a multi-mode correction. Moreover, to mitigate heat fluxes using poloidal flux expansion, the pitch angle at the divertor plates must be small (~1°). It is shown that uncorrected error fields may result in potentially significant local perturbation to the pitch angle. Estimates for coil alignment tolerances in NSTX-U are derived based on consideration of both heat flux and core resonant fields independently.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of equilibrium field coil misalignments on the divertor footprints in NSTX-U

The presence of error fields in a tokamak device is inevitable, so it is of fundamental importance to understand their impact on the operation of the device and therefore up to what level they can be tolerated. In this paper a prediction of the impact on the magnetic footprints on the divertor plates due to the misalignment of NSTX-U equilibrium coils is presented. Resistive MHD solutions are used to predict the magnetic field perturbations experienced by the field lines due to the presence of error fields. A linear relation between the magnitude of the misalignment and the area of the magnetic footprints is found, as well as an inverse proportionality between the size of a magnetic footprint and the plasma penetration of the field lines composing the footprint. This study is intended as a starting point in the process of investigating divertor footprints associated with the plasma response to intrinsic error fields with resistive MHD codes. A basic interpretation of the results suggests that large footprints resulting from equilibrium coils misalignment may be desirable, to some extent, to decrease the peak heat load on the divertor components. Lastly, a more complete interpretation of the results presented here will involve a number of complex physics issues, for example pedestal transport and stability along with the role of various scrape-off layer and divertor processes, as well as experimental data to confirm the predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Topological bifurcation of magnetic islands in NSTX-U

The topological bifurcation of magnetic islands is observed in two M3D-C1 linear resistive MHD calculations of model NSTX-U equilibria during the application of small 3D magnetic perturbation fields. In comparing to a DIII-D ELM suppression case, reconstructed from shot 147170 at time slice 3745 ms, we propose that stronger kink response in the NSTX-U plasma may be the primary causes of the bifurcations. Island evolution and bifurcation in both the DIII-D and the two NSTX-U cases with the increase of perturbation current are analyzed. Further, a hypothesis is proposed that such magnetic island topology bears an intrinsic property to confine charged particles and cause their density inside the islands to rise, which is examined by implementing a random kick algorithm in the magnetic field line integration code TRIP3D-GPU to approximate electron collisional transport. Although full consideration of all forces between electrons is missing as it requires 3D large scale kinetic simulation in toroidal geometry, the positive result of this approximate transport simulation does provide first step confirmation towards fully validating the hypothesis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗