Engineering topics

Finkenauer, Blake P.

Publications and source records attributed to Finkenauer, Blake P..

6 records

DOE OSTI2023

Suppressing phase disproportionation in quasi-2D perovskite light-emitting diodes

Electroluminescence efficiencies and stabilities of quasi-two-dimensional halide perovskites are restricted by the formation of multiple-quantum-well structures with broad and uncontrollable phase distributions. Here, we report a ligand design strategy to substantially suppress diffusion-limited phase disproportionation, thereby enabling better phase control. We demonstrate that extending the π-conjugation length and increasing the cross-sectional area of the ligand enables perovskite thin films with dramatically suppressed ion transport, narrowed phase distributions, reduced defect densities, and enhanced radiative recombination efficiencies. Consequently, we achieved efficient and stable deep-red light-emitting diodes with a peak external quantum efficiency of 26.3% (average 22.9% among 70 devices and cross-checked) and a half-life of ~220 and 2.8 h under a constant current density of 0.1 and 12 mA/cm 2 , respectively. Our devices also exhibit wide wavelength tunability and improved spectral and phase stability compared with existing perovskite light-emitting diodes. These discoveries provide critical insights into the molecular design and crystallization kinetics of low-dimensional perovskite semiconductors for light-emitting devices.

14 SOLAR ENERGY↗

DOE OSTI2023

Amine-Thiol/Selenol Chemistry for Efficient and Stable Perovskite Solar Cells

Controlling the crystallization of perovskites is imperative to reduce defect densities in perovskite thin films and extend device lifetimes. In this work, combinations of amine and chalcogenide ligands were introduced in the sequential deposition method to fabricate highly crystalline and orientated formamidinium lead iodide thin films with reduced defect densities and increased charge carrier lifetimes. The dual additives can tune the perovskite intermediate state and control the crystallization leading to devices with improved efficiencies and stabilities. While thiophenol failed to prevent the amine ligand from degrading the perovskite precursors, benzene selenol combinations with amine-ligands drastically changed the solution chemistry to increase the PbI 2 conversion to highly crystalline and orientated α-FAPbI 3 films with lower defect densities. X-ray photoelectron spectroscopy studies reveal benzene selenol evaporates from the thin film leaving behind a modified surface, which is associated with the amine additive. These results indicate the amine selection can be used to tune the surface properties. Lastly, we propose a highly tunable I 2 reduction strategy using chalcogenide chemistry to help enable the realization of perovskite solar cells with high performance and stability.

defects↗

DOE OSTI2022

Degradation and Self-Healing in Perovskite Solar Cells

Organic–inorganic halide perovskites are well-known for their unique self-healing ability. In the presence of strong external stimuli, such as light, temperature, and moisture, high-energy defects are created which can be healed by removing the perovskite from the degradation source. Furthermore, this self-healing ability has been showcased in devices with recoverable performance and day-and-night cycling operation to dramatically extend the device lifetime and even mechanical durability. However, to date, the mechanistic details and theory around this captivating trait are sparse and convoluted by the complex nature of perovskites. With a clear understanding of the intrinsic self-healing property, perovskite solar cells with extended lifetimes and durability can be designed to realize the large-scale commercialization of perovskite solar cells. Here, we spotlight the relevant degradation and self-healing literature and then propose design strategies to help conceptualize future research.

14 SOLAR ENERGY↗

DOE OSTI2021

Quantifying Anionic Diffusion in 2D Halide Perovskite Lateral Heterostructures

Anionic diffusion strongly impacts the stability of halide perovskite materials, but it is still not well understood. Here, a quantitative investigation of in-plane thermally driven anionic inter-diffusion in a series of novel 2D and quasi-2D halide perovskites lateral heterostructures is reported. The calculated diffusion coefficients (D) reveal the inhibition of Br–I inter-diffusion with bulky π-conjugated organic cations compared with short-chain aliphatic organic cations. Furthermore, halide diffusion is found to be faster in quasi-2D (n > 1) than 2D perovskites (n = 1). The increment becomes less apparent as the “n” number increases, akin to the quantum confinement effect observed for band gaps. These trends are rationalized by molecular dynamics simulations of free energy barriers for halide diffusion that reveal mechanisms for suppressing diffusion. We report this work provides important fundamental insights on the anionic migration and diffusion process in halide perovskite materials.

2D materials↗

DOE OSTI2021

Multifunctional Conjugated Ligand Engineering for Stable and Efficient Perovskite Solar Cells

Surface passivation is an effective way to boost the efficiency and stability of perovskite solar cells (PSCs). However, a key challenge faced by most of the passivation strategies is reducing the interface charge recombination without imposing energy barriers to charge extraction. Here, a novel multifunctional semiconducting organic ammonium cationic interface modifier inserted between the light-harvesting perovskite film and the hole-transporting layer is reported. It is shown that the conjugated cations can directly extract holes from perovskite efficiently, and simultaneously reduce interface non-radiative recombination. Together with improved energy level alignment and the stabilized interface in the device, a triple-cation mixed-halide medium-bandgap PSC with an excellent power conversion efficiency of 22.06% (improved from 19.94%) and suppressed ion migration and halide phase segregation, which lead to a long-term operational stability, is demonstrated. Finally, this strategy provides a new practical method of interface engineering in PSCs toward improved efficiency and stability.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Lead-Free Organic–Perovskite Hybrid Quantum Wells for Highly Stable Light-Emitting Diodes

Two-dimensional perovskites that could be regarded as natural organic-inorganic hybrid quantum wells (HQWs) are promising for light-emitting diode (LED) applications. High photoluminescence quantum efficiencies (approaching 80%) and extremely narrow emission bandwidth (less than 20 nm) have been demonstrated in their single crystals; however, a reliable electrically driven LED device has not been realized owing to inefficient charge injection and extremely poor stability. Furthermore, the use of toxic lead raises concerns. Here, we report Sn(II)-based organic-perovskite HQWs employing molecularly tailored organic semiconducting barrier layers for efficient and stable LEDs. Utilizing femtosecond transient absorption spectroscopy, we demonstrate the energy transfer from organic barrier to inorganic perovskite emitter occurs faster than the intramolecular charge transfer in the organic layer. Consequently, this process allows efficient conversion of lower-energy emission associated with the organic layer into higher-energy emission from the perovskite layer. Thus, this greatly broadened the candidate pool for the organic layer. Incorporating a bulky small bandgap organic barrier in the HQW, charge transport is enhanced and ion migration is greatly suppressed. We demonstrate a HQW-LED device with pure red emission, a maximum luminance of 3466 cd m -2 , a peak external quantum efficiency up to 3.33%, and an operational stability of over 150 h, which are significantly better than previously reported lead-free perovskite LEDs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗