Search NASA⌕ Search

Engineering topics

Finsterbusch, Martin

Publications and source records attributed to Finsterbusch, Martin.

Direct Prelithiation of Silicon-Based Composite Electrodes via Island-like Thermal Evaporation

Irreversible losses of Li during solid electrolyte interface (SEI) conditioning is a key contributor to the lower specific capacities observed in silicon-containing Li-ion batteries. Herein, thermal evaporation of between 1 and 20 µm of Li onto Si-based composite anodes has been investigated as a prelithiation method to account for such losses. To account for mechanical strain caused by Li-Si alloying during the deposition, a stainless-steel mesh is applied to the electrodes before prelithiation to form “island-like” deposition on the electrode surface. The open circuit potential was also found to decrease as a function of increased Li evaporation, consistent with the potentials of electrochemically prepared LixSi alloys. Prelithiating to account for irreversible Li losses to SEI formation resulted in full cells with a 15.8% increase in initial coulombic efficiency and a 47.8% reduction in irreversible capacity loss after SEI formation cycling. Subsequent C/3 cycling showed up to a 62.9% increase in specific capacity in prelithiated cells. X-ray photoelectron spectroscopy (XPS) revealed differences in the SEI composition that was formed by electrochemical cycling and reactively formed in prelithiated cells upon exposure to Gen2 + 3% FEC electrolyte. The reactively formed SEI from the spontaneous reaction with lithiated silicon was carbonate-rich while the electrochemical SEI formation showed significantly more LiPFx species, which could play a role in overall cycling performance.

Musgrove, Amanda↗

Optimizing the Composite Cathode Microstructure in All‐Solid‐State Batteries by Structure‐Resolved Simulations

Abstract All‐solid‐state batteries are considered as an enabler for applications requiring high energy and power density. However, they still fall short of their theoretical potential due to various limitations. One issue is poor charge transport kinetics resulting from both material inherit limitations and non‐optimized design. Therefore, a better understanding of the relevant properties of the cathode microstructure is necessary to improve cell performance. In this article, we identify optimization potentials of the composite cathode by structure‐resolved electrochemical 3D‐simulations. In our simulation study, we investigate the influence of cathode active material fraction, density, particle size, and active material properties on cell performance. Special focus is set on the impact of grain boundaries on the cathode design. Based on our simulation results, we can predict target values for cell manufacturing and reveal promising optimization strategies for an improved cathode design.

25 ENERGY STORAGE↗

The Riddle of Dark LLZO: Cobalt Diffusion in Garnet Separators of Solid‐State Lithium Batteries

Abstract Solid‐state batteries (SSBs) with a Li 7 La 3 Zr 2 O 12 (LLZO) garnet electrolyte are attracting much attention as robust and safe alternative to conventional lithium‐ion batteries. Technical challenges in the practical implementation of garnet SSBs are related to the need for high‐temperature sintering, which often leads to undesirable chemical reactions with the cathode material. While these reactions are well understood for composite cathodes, very little is known about similar processes between cathode and separator during battery fabrication. This work focuses on understanding the processes between the composite LiCoO 2 ‐LLZO cathode and the LLZO separator and how they affect the battery performance. The extensive diffusion of Co‐ions within LLZO, which leads to the often‐observed LLZO darkening, is shown to have a significant impact on ionic conductivity, electronic conductivity, and dendrite stability of the separator. Experimental data coupled with large‐scale molecular dynamics simulations uncover the diffusion mechanism for Co‐ions and identify secondary phases that form during these interactions. In addition to extensive Co‐ion diffusion within the grains, a non‐uniform segregation of Co‐ions at grain boundaries is found leading to the formation of three distinct Co‐containing phases. This work offers a general approach to studying the fundamental ion diffusion processes that occur during the fabrication of oxide SSBs.

electrochemical properties↗

Oxide‐Based Solid‐State Batteries: A Perspective on Composite Cathode Architecture

Abstract The garnet‐type phase Li 7 La 3 Zr 2 O 12 (LLZO) attracts significant attention as an oxide solid electrolyte to enable safe and robust solid‐state batteries (SSBs) with potentially high energy density. However, while significant progress has been made in demonstrating compatibility with Li metal, integrating LLZO into composite cathodes remains a challenge. The current perspective focuses on the critical issues that need to be addressed to achieve the ultimate goal of an all‐solid‐state LLZO‐based battery that delivers safety, durability, and pack‐level performance characteristics that are unobtainable with state‐of‐the‐art Li‐ion batteries. This perspective complements existing reviews of solid/solid interfaces with more emphasis on understanding numerous homo‐ and heteroionic interfaces in a pure oxide‐based SSB and the various phenomena that accompany the evolution of the chemical, electrochemical, structural, morphological, and mechanical properties of those interfaces during processing and operation. Finally, the insights gained from a comprehensive literature survey of LLZO–cathode interfaces are used to guide efforts for the development of LLZO‐based SSBs.

25 ENERGY STORAGE↗

The effects of aluminum concentration on the microstructural and electrochemical properties of lithium lanthanum zirconium oxide

Cubic lithium lanthanum zirconium oxide (Li 7-x Al x La 3 Zr 2 O 12 , LLZO) garnet has gained attention as a promising next-generation electrolyte for lithium batteries due to its high ionic conductivity and chemical stability with lithium metal. The high conductivity can be achieved through doping over a range of aluminum concentrations. In this study, we hot-pressed samples to achieve <2% nominal porosity with aluminum concentrations from x = 0.25–0.55 mol to understand the effect of aluminum on microstructure and electrochemistry. It was observed that beyond the aluminum solubility limit (x = ~0.40), resistive secondary phases formed at the grain boundaries. As a result, the percent grain boundary resistance increased from 17.6 to 41.2% for x = 0.25 and x = 0.55, respectively. Both the grain boundary and bulk activation energies remained relatively constant as the aluminum concentrations increased (~0.44 eV and ~0.39 eV, respectively). It was, therefore, surmised that the mobility term of the Nernst–Einstein equation was roughly independent of aluminum concentration and the major variable controlling bulk conductivity was the number of lithium charge carriers. As a result, as the aluminum concentration increased from x = 0.25 to x = 0.55 the bulk conductivity decreased from 0.56 to 0.15 mS cm -1 . Following these trends of increasing grain boundary resistance and decreasing bulk conductivity with increasing aluminum concentration, x = 0.25 had the highest total conductivity (0.46 mS cm -1 ). We demonstrated that aluminum concentration has a significant effect on the microstructure and electrochemical properties of LLZO. In conclusion, we believe this work could help understand how to link processing, microstructure, and electrochemical properties to guide the manufacturing of LLZO for use in solid-state batteries.

25 ENERGY STORAGE↗

Digestion processes and elemental analysis of oxide and sulfide solid electrolytes

Detailed elemental analysis is essential for a successful development and optimization of material systems and synthesis methods. This is especially relevant for Li- and Na-containing compounds, found in state-of-the-art and next-generation battery systems. Their materials’ properties and thus the final device performance strongly depend on the crystal structure, the stoichiometry, and defect chemistry, e.g., influencing charge carrier concentration and activation energies for vacancy transport. However, a detailed quantitative analysis of light elements in a heavy matrix, featuring a broad range of solubilities and vapor pressures, is often difficult and associated with large uncertainties and thus neglected in favor of just reporting the stoichiometry as “weighed in.” Here, in this work, we report several approaches to digest and dissolve various oxide and sulfide-based materials, used in next-generation Li batteries, for elemental analysis via optical emission spectroscopy. These include the most common solid electrolytes Li-La-Ti–O, a perovskite material (LLTO), and Li-La-Zr-O which has garnet structure (LLZO). Additionally, a facile thermal digestion process is reported for a surrogate sulfide solid electrolyte (Na 2 S). The digestion procedures reported here are suitable for almost any laboratory environment and, when applied, will improve understanding of the synthesis-structure–property correlations needed to advanced batteries with all solid-state configurations.

Malkowski, Thomas F.↗

Effect of Cr2O3 on the O-18 Tracer Incorporation in SOFC Materials

To gain insight into the Cr poisoning mechanism at the cathode side of solid oxide fuel cells (SOFCs) with stainless steel interconnects, we conducted an investigation of the impact of Cr2O3 overlayers on oxygen diffusion in various SOFC electrolyte and cathode materials. High density Gd0.10Ce0.90O2 (GDC), Y0.15Zr0.85O2 (YSZ) and La0.6Sr0.4Co0.2Fe0.8O2 (LSCF) sintered pellets were covered with 3 to 30 nm Cr - overlayers that were subsequently oxidized, forming Cr2O3. Standard 18O tracer diffusion experiments at 800°C were performed and TOFSIMS profiling revealed a Cr2O3 thickness-dependent oxygen uptake process. The oxygen ion diffusion coefficients were found to be unaffected by the Cr2O3 overlayers, which is predictable since they are a bulk property. The extracted surface exchange coefficients however varied with Cr2O3 overlayer thickness. Solid state reaction measurements of Cr2O3 with the three materials of interest, and electronic structure considerations concerning the surface exchange, led to the conclusion that the observed oxygen uptake hindrance for LSCF and the slight increase of the surface exchange coefficient for YSZ can be attributed to the electronic properties of Cr2O3. The rate limitation of the oxygen incorporation into the materials is therefore strongly dependent on the surface electronic properties. A critical thickness of Cr2O3 was determined where the transition from decreased cathode-performance to a Cr2O3-property-governed regime occurs.

30 DIRECT ENERGY CONVERSION↗