Search NASA⌕ Search

Engineering topics

Fleeter, S.

Publications and source records attributed to Fleeter, S..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Effect of wind tunnel acoustic modes on linear oscillating cascade aerodynamics

The aerodynamics of a biconvex airfoil cascade oscillating in torsion is investigated using the unsteady aerodynamic influence coefficient technique. For subsonic flow and reduced frequencies as large as 0.9, airfoil surface unsteady pressures resulting from oscillation of one of the airfoils are measured using flush-mounted high-frequency-response pressure transducers. The influence coefficient data are examined in detail and then used to predict the unsteady aerodynamics of a cascade oscillating at various interblade phase angles. These results are correlated with experimental data obtained in the traveling-wave mode of oscillation and linearized analysis predictions. It is found that the unsteady pressure disturbances created by an oscillating airfoil excite wind tunnel acoustic modes, which have detrimental effects on the experimental results. Acoustic treatment is proposed to rectify this problem.

Buffum, D. H.↗
NASA NTRS1991

Impeller flow field measurement and analysis

A series of experiments are performed to investigate and quantify the three-dimensional mean flow field in centrifugal compressor flow passages and to evaluate contemporary internal flow models. The experiments include the acquisition and analysis of LDV data in the impeller passages of a low-speed moderate-scale research mixed-flow centrifugal compressor operating at its design point. Predictions from a viscous internal flow model are then correlated with these data. The LDV data show the traditional jet-wake structure observed in many centrifugal compressors, with the wake observed along the shroud 70 percent of the length from the pressure to suction surface. The viscous model predicts the major flow phenomena. However, the correlations of the viscous predictions with the LDV data were poor.

Fagan, J. R.↗
NASA NTRS1991

Wind tunnel wall effects in a linear oscillating cascade

Experiments in a linear oscillating cascade reveal that the wind tunnel walls enclosing the airfoils have, in some cases, a detrimental effect on the oscillating cascade aerodynamics. In a subsonic flowfield, biconvex airfoils are driven simultaneously in harmonic, torsion-mode oscillations for a range of interblade phase angle values. It is found that the cascade dynamic periodicity - the airfoil to airfoil variation in unsteady surface pressure - is good for some values of interblade phase angle but poor for others. Correlation of the unsteady pressure data with oscillating flat plate cascade predictions is generally good for conditions where the periodicity is good and poor where the periodicity is poor. Calculations based upon linearized unsteady aerodynamic theory indicate that pressure waves reflected from the wind tunnel walls are responsible for the cases where there is poor periodicity and poor correlation with the predictions.

Buffum, D. H.↗
NASA NTRS1990

The aerodynamics of an oscillating cascade in a compressible flow field

Fundamental experiments are performed in the NASA Lewis Research Center Transonic Oscillating Cascade Facility to investigate and quantify the aerodynamics of a cascade of bioconvex airfoils executing torsion mode oscillations at realistic reduced frequency values. Both steady and unsteady airfoil surface pressures are measured at two inlet Mach numbers, 0.65 and 0.80, and two incidence angles, 0 and 7 deg, with the harmonic torsional airfoil cascade oscillations at realistic high reduced frequency and unsteady data obtained at several interblade phase angle values. The time-variant pressures are analyzed by means of discrete Fourier transform techniques, with these unique data compared with predictions from a linearized unsteady cascade model. The experimental results indicate that the interblade phase angle has a major effect on the chordwise distributions of the airfoil surface unsteady pressure, with the effect of reduced frequency, incidence angle, and Mach numbers somewhat less significant.

Buffum, D. H.↗
NASA NTRS1989

Three-dimensional aerodynamics of an annular airfoil cascade including loading effects

A series of experiments are described which investigate and quantify the effect of loading on the three-dimensional flow through a subsonic annular cascade of cambered airfoils. At two levels of loading, detailed data quantify the cascade inlet velocity, the intrapassage flow field, the airfoil surface pressure distributions, the exit flow field, and the total pressure loss distributions. Aerodynamic loading is shown to strengthen the radial pressure gradient, the passage vortex structure, the vortex-endwall boundary layer interactions, and the losses.

Fleeter, S.↗
NASA NTRS1987

LDA measurement of the passage flow field in an annular airfoil cascade

Models to predict the complex three-dimensional flow through turbomachine blade rows are being developed. To verify these models and direct necessary refinements, it is necessary that predictions be correlated with data obtained in experiments which model the fundamental three-dimensional blade row flow phenomena. This paper describes a series of experiments performed in a large scale, subsonic, annular cascade facility specifically designed to provide such data. In particular, the effect of incidence angle on the three-dimensional passage flow field through an annular cascade of cambered airfoils is investigated and quantified, accomplished by obtaining detailed and expensive LDA data. These data demonstrate and quantify the development of the passage vortices through the airfoil passage and their strong interaction with the endwall boundary layers.

Stauter, R. C.↗
NASA NTRS1986

The effect of circumferential aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter

A mathematical model developed to predict the enhanced coupled bending-torsion unstalled supersonic flutter stability due to alternate circumferential spacing aerodynamic detuning of a turbomachine rotor. The translational and torsional unsteady aerodynamic coefficients are developed in terms of influence coefficients, with the coupled bending-torsion stability analysis developed by considering the coupled equations of this aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter as well as the verification of the modeling are then demonstrated by considering an unstable 12 bladed rotor, with Verdon's uniformly spaced Cascade B flow geometry as a baseline. However, with the elastic axis and center of gravity at 60 percent of the chord, this type of aerodynamic detuning has a minimal effect on stability. For both uniform and nonuniform circumferentially space rotors, a single degree of freedom torsion mode analysis was shown to be appropriate for values of the bending-torsion natural frequency ratio lower than 0.6 and higher 1.2. When the elastic axis and center of gravity are not coincident, the effect of detuning on cascade stability was found to be very sensitive to the location of the center of gravity with respect to the elastic axis. In addition, it was determined that when the center of gravity was forward of an elastic axis located at midchord, a single degree of freedom torsion model did not accurately predict cascade stability.

Hoyniak, D.↗
NASA NTRS1986

Splitter blades as an aeroelastic detuning mechanism for unstalled supersonic flutter of turbomachine rotors

Splitter plates usable as aeroelastic detuner devices for supersonic flutter in turbomachinery, through the introduction of both aerodynamic and structural detuning to enhance aeroelastic stability, are presently considered by a mathematical model. The model demonstrates that aerodynamic detuning is due to both the alternate circumferential spacing of the full chord airfoils and the variable circumferentially spaced splitters between each pair of full chord airfoils. Structural detuning is based on the lower natural frequencies of the splitters, by comparison with the full chord airfoils. The model's application to two unstable rotors demonstrates enhanced torsion mode flutter stability through the incorporation of splitters, where the critical parameters are chord length and the circumferential and axial locations of the splitters.

Topp, D. A.↗
NASA NTRS1986

Aerodynamic performance of an annular flat plate airfoil cascade with nonuniform inlet velocity

The demand for increased gas turbine engine efficiency with minimum weight is leading to more complex blading designs, in which viscous and three-dimensional effects are significant. As a result, design procedures based on first principle, experimentally verified, three-dimensional aerodynamic analyses are required. This paper describes a series of experiments performed in a large-scale, subsonic, annular cascade facility specifically designed to provide three-dimensional aerodynamic data suitable for code verification. In particular, the effect of inlet velocity profile on the overall three-dimensional performance of a classical flat plate airfoil cascade is investigated over a range of incidence angles including those resulting in airfoil surface flow separation. All of the data are analyzed and correlated with appropriate nonseparated flow predictions.

Buffum, D.↗
NASA NTRS1986

The predicted effect of aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter

A mathematical model is developed to predict the enhanced coupled bending-torsion unstalled supersonic flutter stability due to alternate circumferential spacing aerodynamic detuning of a turbomachine rotor. The translational and torsional unsteady aerodynamic coefficients are developed in terms of influence coefficients, with the coupled bending-torsion stability analysis developed by considering the coupled equations of motion together with the unsteady aerodynamic loading. The effect of this aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter as well as the verification of the modeling are then demonstrated by considering an unstable 12 bladed rotor, with Verdon's uniformly spaced Cascade B flow geometry as a baseline. However, with the elastic axis and center of gravity at 60 percent of the chord, this type of aerodynamic detuning has a minimal effect on stability. For both uniform and nonuniform circumferentially space rotors, a single degree of freedom torsion mode analysis was shown to be appropriate for values of the bending-torsion natural frequency ratio lower than 0.6 and higher 1.2. When the elastic axis and center of gravity are not coincident, the effect of detuning on cascade stability was found to be very sensitive to the location of the center of gravity with respect to the elastic axis. In addition, it was determined that when the center of gravity was forward of an elastic axis located at midchord, a single degree of freedom torsion model did not accurately predict cascade stability.

Hoyniak, D.↗
NASA NTRS1986

LDA measurement of the passage flow field in a 3-D airfoil cascade

Three-dimensional internal flow computational models are currently being developed to predict the flow through turbomachinery blade rows. For these codes to be of quantitative value, they must be verified with data obtained in experiments which model the fundamental flow phenomena. In this paper, the complete three-dimensional flow field through a subsonic annular cascade of cambered airfoils is experimentally quantified. In particular, detailed three-dimensional data are obtained to quantify the inlet velocity profile, the cascade passage velocity field, and the exit region flow field. The primary instrumentation for acquiring these data is a single-channel Laser Doppler Anemometer operating in the backscatter mode, with chordwise distributions of airfoil surface static pressure taps also utilized. Appropriate data are correlated with predictions from the MERIDL/TSONIC codes.

Stauter, R. C.↗
NASA NTRS1986

Aerodynamic detuning analysis of an unstalled supersonic turbofan cascade

An approach to passive flutter control is aerodynamic detuning, defined as designed pasage-to-passage differences in the unsteady aerodynamic flow field of a rotor blade row. Thus, aerodynamic detuning directly affects the fundamental driving mechanism for flutter. A model to demonstrate the enhanced supersonic aeroelastic stability associated with aerodynamic detuning is developed. The stability of an aerodynamicaly detuned cascade operating in a supersonic inlet flow field with a subsonic leading edge locus analyzed, with the aerodynamic detuning accomplished by means of nonuniform circumferential spacing of adjacent rotor blades. The unsteady aerodynamic forces and moments on the blading are defined in terms of influence coefficients in a manner that permits the stability of both a conventional uniformally spaced rotor configuration as well as the detuned nonuniform circumferentialy spaced rotor to be determined. With Verdon's uniformly spaced Cascade B as a baseline, this analysis is then utilized to demonstrate the potential enhanced aeroelastic stability associated with this particular type of aerodynamic detuning.

Hoyniak, D.↗
NASA NTRS1986

Passive control of aerodynamically forced vibrations of supersonic turbomachine rotors by splitter blades

An aeroelastic model is developed to examine the use of splitter blades as a passive detuning mechanism for flow induced forced response of unstalled supersonic turbomachine rotors. The splitters introduce aerodynamic and structural detuning to the rotor design. The relationship between aerodynamic and structural detuning and the location and chord lengths of splitters is analyzed. The model is applied to the flow induced response of four 12-blade rotors with Verdon's (1973) Cascade B flow geometry. The data reveal that for gusts characterized by forward and backward traveling waves the splitters generally decrease the maximum amplitudes of response; however, for some gust load interblade phase angles, such as -180 deg and 120 deg the splitters did not reduce the amplitudes of response.

Fleeter, S.↗
NASA NTRS1985

Aerodynamic detuning analysis of an unstalled supersonic turbofan cascade

An approach to passive flutter control is aerodynamic detuning, defined as designed passage-to-passage differences in the unsteady aerodynamic flow field of a rotor blade row. Thus, aerodynamic detuning directly affects the fundamental driving mechanism for flutter. A model to demonstrate the enhanced supersonic aeroelastic stability associated with aerodynamic detuning is developed. The stability of an aerodynamically detuned cascade operating in a supersonic inlet flow field with a subsonic leading edge locus is analyzed, with the aerodynamic detuning accomplished by means of nonuniform circumferential spacing of adjacent rotor blades. The unsteady aerodynamic forces and moments on the blading are defined in terms of influence coefficients in a manner that permits the stability of both a conventional uniformally spaced rotor configuration as well as the detuned nonuniform circumferentially spaced rotor to be determined. With Verdon's uniformly spaced Cascade B as a baseline, this analysis is then utilized to demonstrate the potential enhanced aeroelastic stability associated with this particular type of aerodynamic detuning.

Hoyniak, D.↗
NASA NTRS1985

Three dimensional aerodynamics of an annular cascade in a non-uniform inlet flow

Three-dimensional viscous and inviscid numerical analyses are currently being developed to predict the complex flow through turbomachine blade passages. To be of value to the designer, these numerical solutions must be evaluated and subsequent refinements directed by correlating predicted flow fields with data obtained from experiments which model the fundamental three-dimensional flow phenomena inherent in blade rows. This paper describes a series of experiments to provide such data. In particular, the effect of a potential and a rotational inlet flow field on the detailed three-dimensional aerodynamic performance of an extensively instrumented cambered airfoil cascade has been determined at two levels of aerodynamic loading. Data presented quantify the pressure and suction surface static pressure chordwise distributions on the hub, mean, and tip streamlines; the velocity distribution in the cascade aft-passage region; and the cascade exit region flow field. Appropriate data are correlated with predictions.

Manwaring, S. R.↗
NASA NTRS1985

The effect of aerodynamic and structural detuning on turbomachine supersonic unstalled torsional flutter

The effects of alternate-blade structural detuning and adjacent-blade alternate-circumferential-spacing aerodynamic detuning on the supersonic unstalled torsional flutter stability of a turbomachine rotor are investigated analytically. An unsteady aerodynamic model employing influence coefficients is constructed for the case of a flat-plate-airfoil cascade in torsion-mode harmonic oscillation in a supersonic inviscid isentropic adiabatic irrotational perfect-gas inlet flow with a subsonic leading-edge locus. The influence coefficients and equations of motion are derived; the model is verified by applying it to the 12-blade cascade-B flow geometry studied by Verdon and McCune (1975); and the results are presented graphically. It is found that the rotor can be stabilized over the entire reduced frequency range by applying a combination of structural and aerodynamic detuning as the passive flutter-control mechanism.

Hoyniak, D.↗
NASA NTRS1985

Forced response analysis of an aerodynamically detuned supersonic turbomachine rotor

High performance aircraft-engine fan and compressor blades are vulnerable to aerodynamically forced vibrations generated by inlet flow distortions due to wakes from upstream blade and vane rows, atmospheric gusts, and maldistributions in inlet ducts. In this report, an analysis is developed to predict the flow-induced forced response of an aerodynamically detuned rotor operating in a supersonic flow with a subsonic axial component. The aerodynamic detuning is achieved by alternating the circumferential spacing of adjacent rotor blades. The total unsteady aerodynamic loading acting on the blading, as a result of the convection of the transverse gust past the airfoil cascade and the resulting motion of the cascade, is developed in terms of influence coefficients. This analysis is used to investigate the effect of aerodynamic detuning on the forced response of a 12-blade rotor, with Verdon's Cascade B flow geometry as a uniformly spaced baseline configuration. The results of this study indicate that, for forward traveling wave gust excitations, aerodynamic detuning is very beneficial, resulting in significantly decreased maximum-amplitude blade responses for many interblade phase angles.

Hoyniak, D.↗