Search NASASearch

Engineering topics

Fleming, David P.

Publications and source records attributed to Fleming, David P..

At least 19 records

The Habitability of Proxima Centauri b: Environmental States and Observational Discriminants

Proxima Centauri b provides an unprecedented opportunity to understand the evolution and nature of terrestrial planets orbiting M dwarfs. Although Proxima Cen b orbits within its star’s habitable zone, multiple plausible evolutionary paths could have generated different environments that may or may not be habitable. Here, we use 1-D coupled climate-photochemical models to generate self-consistent atmospheres for several evolutionary scenarios, including high-O2, high-CO2, and more Earth-like atmospheres, with both oxic and anoxic compositions. We show that these modeled environments can be habitable or uninhabitable at Proxima Cen b's position in the habitable zone. We use radiative transfer models to generate synthetic spectra and thermal phase curves for these simulated environments, and use instrument models to explore our ability to discriminate between possible planetary states. These results are applicable not only to Proxima Cen b but to other terrestrial planets orbiting M dwarfs. Thermal phase curves may provide the first constraint on the existence of an atmosphere. We find that James Webb Space Telescope ( JWST) observations longward of 10 mm could characterize atmospheric heat transport and molecular composition. Detection of ocean glint is unlikely with JWST but may be within the reach of larger-aperture telescopes. Direct imaging spectra may detect O4 absorption, which is diagnostic of massive water loss and O2 retention, rather than a photosynthetic biosphere. Similarly, strong CO2 and CO bands at wavelengths shortward of 2.5 mm would indicate a CO2-dominated atmosphere. If the planet is habitable and volatile-rich, direct imaging will be the best means of detecting habitability. Earth-like planets with microbial biospheres may be identified by the presence of CH4-which has a longer atmospheric lifetime under Proxima Centauri's incident UV-and either photosynthetically produced O2 or a hydrocarbon haze layer.

Meadows, Victoria S.

Vibration Transmission through Bearings with Application to Gearboxes

Cabin noise has become a major concern to manufacturers and users of helicopters. Gear noise is the largest part of this unwanted sound. The crucial noise path is generally considered to be from the gears through the gear-supporting shafts and bearings into the gearbox case, and from there either through the gearbox mounts or the surrounding air to the helicopter cabin. If the noise, that is, the gear and shaft vibration, can be prevented from traveling through the gearbox bearings, then the noise cannot make its way into the helicopter cabin. Thus the vibration-transmitting properties of bearings are of paramount importance. This paper surveys the literature concerning evaluation of properties for the types of bearings used in helicopter gearboxes. A simple model is proposed to evaluate vibration transmission, using measured or calculated bearing stiffness and damping. Less-commonly used types of gearbox bearings (e.g., fluid film) are evaluated for their potential in reducing vibration transmission.

Fleming, David P.

Transient Response of Rotor on Rolling-Element Bearings with Clearance

Internal clearance in rolling element bearings is usually present to allow for radial and axial growth of the rotor-bearing system and to accommodate bearing fit-up. The presence of this clearance also introduces a "dead band" into the load-deflection behavior of the bearing. Previous studies demonstrated that the presence of dead band clearance might have a significant effect on synchronous rotor response. In this work, the authors investigate transient response of a rotor supported on rolling element bearings with internal clearance. In addition, the stiffness of the bearings varies nonlinearly with bearing deflection and with speed. Bearing properties were accurately calculated with a state of the art rolling bearing analysis code. The subsequent rotordynamics analysis shows that for rapid acceleration rates the maximum response amplitude may be less than predicted by steady-state analysis. The presence of clearance may shift the critical speed location to lower speed values. The rotor vibration response exhibits subharmonic components which are more prominent with bearing clearance.

Fleming, David P.

Unbalance Response Prediction for Accelerating Rotors With Load-Dependent Nonlinear Bearing Stiffness

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. Previous papers have explored the transient effect of suddenly applied imbalance and the steady-state unbalance response, using bearing forces calculated by the rolling-element bearing analysis code COBRA-AHS. The present work considers the acceleration of a rotor through one or more critical speeds. The rotordynamic analysis showed that for rapid acceleration rates the maximum response amplitude may be considerably less than predicted by steady-state analysis. Above the critical speed, transient vibration at the rotor natural frequency occurs, similar to that predicted for a Jeffcott rotor with constant-stiffness bearings. A moderate amount of damping will markedly reduce the vibration amplitude, but this damping is not inherent in ball bearings.

Fleming, David P.

Software Developed for Analyzing High- Speed Rolling-Element Bearings

COBRA-AHS (Computer Optimized Ball & Roller Bearing Analysis--Advanced High Speed, J.V. Poplawski & Associates, Bethlehem, PA) is used for the design and analysis of rolling element bearings operating at high speeds under complex mechanical and thermal loading. The code estimates bearing fatigue life by calculating three-dimensional subsurface stress fields developed within the bearing raceways. It provides a state-of-the-art interactive design environment for bearing engineers within a single easy-to-use design-analysis package. The code analyzes flexible or rigid shaft systems containing up to five bearings acted upon by radial, thrust, and moment loads in 5 degrees of freedom. Bearing types include high-speed ball, cylindrical roller, and tapered roller bearings. COBRA-AHS is the first major upgrade in 30 years of such commercially available bearing software. The upgrade was developed under a Small Business Innovation Research contract from the NASA Glenn Research Center, and incorporates the results of 30 years of NASA and industry bearing research and technology.

Fleming, David P.

Approximate Solution for Choked Flow in Gas Seal Pads

Previous analyses of high pressure seals have considered adiabatic flow with friction but neglected effects of seal rotation. Most of this work analyzed a one-dimensional flow field. This works well to calculate stiffness and leakage of full circular seals, either face seals or annular ring seals. However, it cannot provide accurate results for a rectangular seal pad with its strongly two-dimensional flow field and its reliance on hydrodynamic forces to maintain a full fluid film. On the other hand, solutions of Reynolds lubrication equation have been obtained for the two-dimensional flow in a seal pad. But these solutions do not account for choking which occurs at high seal pressure ratios, nor do they consider the pressure loss that occurs in the entrance region of the flow field. The aim of the present work is to build on the Reynolds equation solution by use of an approximate choked flow analysis. This will account for the pressure losses in the flow entrance region, ensure that fluid velocities remain subsonic, and enable fluid inertial effects within the pad film to be accounted for. Results show that, in general, fluid inertia acts to decrease pad film load capacity and leakage, and increase film stiffness.

Fleming, David P.

Unbalance Response Prediction for Rotors on Ball Bearings Using Speed and Load Dependent Nonlinear Bearing Stiffness

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant bearing stiffness. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

Fleming, David P.

Computation of Pressurized Gas Bearings Using CE/SE Method

The space-time conservation element and solution element (CE/SE) method is extended to compute compressible viscous flows in pressurized thin fluid films. This numerical scheme has previously been used successfully to solve a wide variety of compressible flow problems, including flows with large and small discontinuities. In this paper, the method is applied to calculate the pressure distribution in a hybrid gas journal bearing. The formulation of the problem is presented, including the modeling of the feeding system. the numerical results obtained are compared with experimental data. Good agreement between the computed results and the test data were obtained, and thus validate the CE/SE method to solve such problems.

Cioc, Sorin

Transient Vibration Prediction for Rotors on Ball Bearings Using Load-dependent Non-linear Bearing Stiffness

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic transient analysis requires bearing forces to be determined at each step of the transient solution. Analyses have been carried out to show the effect of accurate bearing transient forces (accounting for non-linear speed and load dependent bearing stiffness) as compared to conventional use of average rolling-element bearing stiffness. Bearing forces were calculated by COBRA-AHS (Computer Optimized Ball and Roller Bearing Analysis - Advanced High Speed) and supplied to the rotordynamics code ARDS (Analysis of Rotor Dynamic Systems) for accurate simulation of rotor transient behavior. COBRA-AHS is a fast-running 5 degree-of-freedom computer code able to calculate high speed rolling-element bearing load-displacement data for radial and angular contact ball bearings and also for cylindrical and tapered roller beatings. Results show that use of nonlinear bearing characteristics is essential for accurate prediction of rotordynamic behavior.

Fleming, David P.

Effect of Bearing Dynamic Stiffness on Gear Vibration

Noise is a major consideration in the design of high performance geared transmissions, such as for helicopters. Transmission error, that is, the accuracy with which the driven gear follows the driver gear, is a common indicator of noise generation. It is well known that bearing properties have a strong influence on shaft dynamics. However, up to now the contribution of bearings to transmission error has received little attention. In this paper, a torsional-axial-lateral geared rotor analysis is used to determine dynamic transmission error as a function of bearing stiffness and damping. Bearings have a similar effect as found in shaft dynamics; transmission error can be reduced more than 10 decibels by appropriate selection of bearing properties.

Fleming, David P.

Rotordynamic Influence on Rolling ELement Bearing Selection and Operation

Three case studies are presented that illustrate the importance of dynamic considerations in the design of machinery supported by rolling element bearings. The first case concerns a milling spindle that experienced internal rubs and high bearing loads, and required retrofit of an additional . damped bearing. The second case deals with a small high-speed generator that suffered high vibration due to flexible mounting. The third case is a propulsion fan simulator rig whose bearings failed catastrophically due to improper bearing installation (which resulted in inadequate dynamic bearing stiffness) and lack of health monitoring instrumentation.

Queitzsch, Gilbert K., Jr.

ARDS User Manual

Personal computers (PCs) are now used extensively for engineering analysis. their capability exceeds that of mainframe computers of only a few years ago. Programs originally written for mainframes have been ported to PCs to make their use easier. One of these programs is ARDS (Analysis of Rotor Dynamic Systems) which was developed at Arizona State University (ASU) by Nelson et al. to quickly and accurately analyze rotor steady state and transient response using the method of component mode synthesis. The original ARDS program was ported to the PC in 1995. Several extensions were made at ASU to increase the capability of mainframe ARDS. These extensions have also been incorporated into the PC version of ARDS. Each mainframe extension had its own user manual generally covering only that extension. Thus to exploit the full capability of ARDS required a large set of user manuals. Moreover, necessary changes and enhancements for PC ARDS were undocumented. The present document is intended to remedy those problems by combining all pertinent information needed for the use of PC ARDS into one volume.

Fleming, David P.

Wave Fluid Film Bearing Tests for an Aviation Gearbox

An oil-lubricated wave journal-thrust bearing assembly was successfully tested at conditions found in general aviation engine gearboxes. The bearing performed well at both steady state conditions and in start-stop tests. It ran stably under all loading conditions, including zero load, at all speeds up to 16 000 rpm. The bearing carried 25 percent more load than required for the gearbox application, supporting 8900 N (94 bars average pressure), and showed very good thermal stability. 450 start-stop cycles were also performed, including 350 cycles without oil supply during starting and stopping. Test results and numerical predictions were in good agreement.

Dimofte, Florin

Rotordynamics on the PC: Further Capabilities of ARDS

Rotordynamics codes for personal computers are now becoming available. One of the most capable codes is Analysis of RotorDynamic Systems (ARDS) which uses the component mode synthesis method to analyze a system of up to 5 rotating shafts. ARDS was originally written for a mainframe computer but has been successfully ported to a PC; its basic capabilities for steady-state and transient analysis were reported in an earlier paper. Additional functions have now been added to the PC version of ARDS. These functions include: 1) Estimation of the peak response following blade loss without resorting to a full transient analysis; 2) Calculation of response sensitivity to input parameters; 3) Formulation of optimum rotor and damper designs to place critical speeds in desirable ranges or minimize bearing loads; 4) Production of Poincard plots so the presence of chaotic motion can be ascertained. ARDS produces printed and plotted output. The executable code uses the full array sizes of the mainframe version and fits on a high density floppy disc. Examples of all program capabilities are presented and discussed.

Fleming, David P.

Rotordynamics on the PC: Transient Analysis With ARDS

Personal computers can now do many jobs that formerly required a large mainframe computer. An example is NASA Lewis Research Center's program Analysis of RotorDynamic Systems (ARDS), which uses the component mode synthesis method to analyze the dynamic motion of up to five rotating shafts. As originally written in the early 1980's, this program was considered large for the mainframe computers of the time. ARDS, which was written in Fortran 77, has been successfully ported to a 486 personal computer. Plots appear on the computer monitor via calls programmed for the original CALCOMP plotter; plots can also be output on a standard laser printer. The executable code, which uses the full array sizes of the mainframe version, easily fits on a high-density floppy disk. The program runs under DOS with an extended memory manager. In addition to transient analysis of blade loss, step turns, and base acceleration, with simulation of squeeze-film dampers and rubs, ARDS calculates natural frequencies and unbalance response.

Fleming, David P.

Advances In Magnetic Bearings

NASA technical memorandum reviews state of technology of magnetic bearings, focusing mainly on attractive bearings rather than repulsive, eddy-current, or Lorentz bearings. Attractive bearings offer greater load capacities and preferred for aerospace machinery.

Fleming, David P.

Magnetic bearings - State of the art

Magnetic bearings have existed for many years, at least in theory. Earnshaw's theorem, formulated in 1842, concerns stability of magnetic suspensions, and states that not all axes of a bearing can be stable without some means of active control. In Beam's widely referenced experiments, a tiny (1/64 in diameter) rotor was rotated to the astonishing speed of 800,000 rps while it was suspended in a magnetic field. Despite a long history, magnetic bearings have only begun to see practical application since about 1980. The development that finally made magnetic bearings practical was solid state electronics, enabling power supplies and controls to be reduced in size to where they are now comparable in volume to the bearings themselves. An attempt is made to document the current (1991) state of the art of magnetic bearings. The referenced papers are large drawn from two conferences publications published in 1988 and 1990 respectively.

Fleming, David P.

Magnetic bearings-state of the art

Magnetic bearings have existed for many years, at least in theory. Earnshaw's theorem, formulated in 1842, concerns stability of magnetic suspensions, and states that not all axes of a bearing can be stable without some means of active control. In Beam's widely referenced experiments, a tiny (1/64 in diameter) rotor was rotated to the astonishing speed of 800,000 rps while it was suspended in a magnetic field. Despite a long history, magnetic bearings have only begun to see practical application since about 1980. The development that finally made magnetic bearings practical was solid state electronics, enabling power supplies and controls to be reduced in size to where they are now comparable in volume to the bearings themselves. An attempt is made to document the current (1991) state of the art of magnetic bearings. The referenced papers are large drawn from two conferences publications published in 1988 and 1990 respectively.

Fleming, David P.