Target Development for XFOL Sc-V Campaign
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Fooks, J. A..
Explore the source record for details and available documents.
We report a target design which produced a substantial gain in relativistic electron-positron pair production using high-intensity lasers and targets with large-scale micro-structures on their surface. Comparing to an unstructured target, a selected Si microwire array target yielded a near 100% increase in the laser-to-positron conversion efficiency and produced a 10MeV increase in the average emitted positron energy under nominally the same experimental conditions. We had established a multi-scale particle-in-cell simulation scheme to simulate both the laser absorption and the subsequent pair productions in a thick metal target. Here, the experimental results are supported by the simulations demonstrating the performance increase is due to a higher conversion efficiency of laser energy into electrons with kinetic energies greater than 10 MeV due to enhanced direct laser acceleration of electrons enabled by the microwire array.
Millimeter-sized CD foils fielded close (order mm) to inertial confinement fusion (ICF) implosions have been proposed as a game-changer for improving energy resolution and allowing time-resolution in neutron spectrum measurements using the magnetic recoil technique. This paper presents results from initial experiments testing this concept for direct drive ICF at the OMEGA laser facility. While the foils are shown to produce reasonable signals, inferred spectral broadening is seen to be high (~5 keV) and signal levels low (by ~20%) compared to expectation. Before this type of foil is used for precision experiments, the foil mount must be improved, oxygen uptake in the foils better characterized, and impact of uncontrolled foil motion prior to detection investigated.
Millimeter-sized CD foils fielded close (order mm) to inertial confinement fusion (ICF) implosions have been proposed as a game-changer for improving energy resolution and allowing time-resolution in neutron spectrum measurements using the magnetic recoil technique. This paper presents results from initial experiments testing this concept for direct drive ICF at the OMEGA Laser Facility. Additionally, while the foils are shown to produce reasonable signals, inferred spectral broadening is seen to be high (~5 keV) and signal levels are low (by ~20%) compared to expectation. Before this type of foil is used for precision experiments, the foil mount must be improved, oxygen uptake in the foils must be better characterized, and impact of uncontrolled foil motion prior to detection must be investigated.
Abstract Focusing effect of laser-driven positron jets by self-generated target sheath fields has been observed for the first time experimentally and the results are supported by the computational studies. In the experiment, OMEGA EP short-pulse (0.7 ps, 500 J) irradiates mm-size gold targets with a concave back surface and reference flat-surface targets. Both targets exhibited positrons with quasi-monoenergetic energy peaks while targets with concave curvature also showed increased number of positrons at the detector. The data is consistent with hybrid-PIC simulations confirming that the time-varying electric fields driven by electrons escaping from the target significantly change the trajectories of positrons. These simulations show a small radius of curvature on the rear side increases the relative focusing effect and the positrons to electrons ratio in the escaping plasma. For the smallest radius of curvature, positron jets that are up to 10 times denser can be achieved.
The magnetized liner inertial fusion (MagLIF) scheme relies on coupling laser energy into an underdense fuel raising the fuel adiabat at the start of the implosion. To deposit energy into the fuel, the laser must first penetrate a laser entrance hole (LEH) foil which can be a significant energy sink and introduce mix. In this paper, we report on experiments investigating laser energy coupling into MagLIF-relevant gas cell targets with LEH foil thicknesses varying from 0.5 μm to 3 μm. Two-dimensional (2D) axisymmetric simulations match the experimental results well for 0.5 μm and 1 μm thick LEH foils but exhibit whole-beam self-focusing and excessive penetration of the laser into the gas for 2 μm and 3 μm thick LEH foils. Additionally, better agreement for the 2 μm-thick foil is found when using a different thermal conductivity model in 2D simulations, while only 3D Cartesian simulations come close to matching the 3 μm-thick foil experiments. The study suggests that simulations may over-predict the tendency for the laser to self-focus during MagLIF preheat when thicker LEH foils are used. This effect is pronounced with 2D simulations where the azimuthally symmetric density channel effectively self-focuses the rays that are forced to traverse the center of the plasma. The extra degree of freedom in 3D simulations significantly reduces this effect. The experiments and simulations also suggest that, in this study, the amount of energy coupled into the gas is highly correlated with the laser propagation length regardless of the LEH foil thickness.
Here, the magnetized liner inertial fusion (MagLIF) experimental campaign conducted at the University of Rochester’s Laboratory for Laser Energetics (LLE) has evolved significantly since its start in 2014. Scientific requirements and OMEGA EP system technology both have progressed, resulting in necessary and available updates to the target design. These include, but are not limited to: optimizing target dimensions and aspect ratios to maximize survival at desired pressures; coating target components to enhance physics diagnosis; precision-machining diagnostic windows along the axis of the target; improving fiducial placement reproducibility and reducing subsequent assembly time by 50%; and implementing gas-pressure transducers on the targets. In addition, target fabrication techniques have changed and improved, allowing for simpler target reproducibility and decreased assembly time. To date, eleven variations of targets have been fabricated, with successful target fielding ranging from 1 to 20atm internal pressure and a maximum survivability of 33atm.