Engineering topics

Francisco Canabal

Publications and source records attributed to Francisco Canabal.

4 records

NASA NTRS2020

Computational Investigation of Powered Descent for Human-Scale Mars Landers

NASA human-scale Mars entry, descent, and landing vehicles currently under consideration have system requirements beyond the current state of the art. Specifically, heritage approaches for deceleration using parachutes and initiating engines at subsonic speeds are not adequate to land these large vehicles (50-60 metric ton entry mass) precisely (within 50 meters of a surface target). Therefore, the present approach for landing humans on Mars utilizes entry vehicles with large aerodynamic surface areas that transition to the descent and landing phase by initiating retropropulsion at supersonic speeds. Vehicle performance, including stability and control, depends on accurate characterization of the aerodynamic-propulsive interference effects, especially at engine initiation, when the vehicles are transitioning from an entry attitude to that suitable for descent and landing. This paper summarizes the human Mars entry vehicle configurations, retropropulsion integration, performance assumptions, and expected flight environment at engine initiation. Cases spanning supersonic, transonic, and subsonic conditions during powered descent are analyzed using four computational fluid dynamics codes, all of which have been previously applied to supersonic retropropulsion at varying scales and conditions. The results of the analysis are used to develop an aerodynamic-propulsive interference model that has since been applied in trajectory simulations to augment the fidelity of human-scale Mars entry vehicle performance.

Ashley M Korzun↗

NASA NTRS2020

Model Design and Pre-Test CFD Analysis for a Supersonic Retropropulsion Wind Tunnel Test

Future Mars human lander missions will require using powered descent beginning at supersonic conditions, something which has never been done before at Mars. Significant aerosciences challenges exist due to interactions between the retrorocket exhaust plumes and the freestream flow that alter the aerodynamic behavior of the powered descent vehicle. Historically, wind tunnel tests have been used to study supersonic retropropulsion with inert gas exhaust simulants. Also, SpaceX has successfully decelerated the Falcon 9 first stage numerous times by using powered flight at supersonic conditions. On the computational side, Reynolds-Averaged Navier-Stokes flowfield simulations are regularly completed at full-scale conditions. However, the available ground and flight data do not provide a basis for calibrating the computational uncertainties for aerodynamic interference forces and moments on proposed Mars descent vehicles, either because of insufficient data or dissimilar vehicles geometries and/or conditions. Thus, additional ground testing is needed to continue addressing the aerosciences risks for large-scale human Mars landers. To that end, a retropropulsion wind tunnel test will be conducted in the NASA Langley Unitary Plan Wind Tunnel in 2020. The test is designed to improve upon similar past tests, both in terms of model design and measured data. The test campaign will use subscale model geometries derived from the two current NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry. This paper covers the reference vehicles, test objectives, model design, scaling parameters, test matrix, and computational analysis to date.

Karl T Edquist↗

NASA NTRSDate not supplied

Computational Modeling of Mars Retropropulsion Concepts in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. A test will be conducted in the NASA Langley Unitary Plan Wind Tunnel to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. This paper covers pre-test computational flowfield predictions of two different models derived from full-scale reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry. Calculations of the blunt model include variations in nozzle configuration: nozzle location, size, area ratio, and pointing direction. There exist some significant differences between solvers, but some general trends are observed from simulations of the blunt model. First, aerodynamic axial force from the heatshield decreases with increasing thrust due to expanding plume blockage. Second, nozzles that point along the model axis result in lower aerodynamic axial force compared to nozzles that have a radial thrust component. Finally, placing the nozzles further away from the model nose preserves more heatshield axial force with increasing thrust com- pared to nozzles that are closer to the nose. For the slender model, the axial force from the heatshield is similar to the non-blowing axial force regardless of thrust magnitude, due to the nozzle arrangement on the heatshield. Once the test is completed, direct comparisons between the computations and test data will be made to determine computational uncertainties in a wind tunnel environment, to identify gaps in predictive capabilities, and to inform planning for future ground and flight test programs for Mars powered descent vehicles.

Mars↗

NASA NTRSDate not supplied

Computational Modeling of Two Mars Powered Descent Vehicle Concepts Tested in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not suitable for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). This paper covers computational flowfield predictions completed at wind tunnel conditions and comparisons to the test data. On the blowing HIAD models, the time-averaged pressure inboard of the nozzles was generally well-predicted, especially if the nozzles are canted outward, when the nozzles are located further from the nose. At intermediate CobraMRV thrust coefficients, CFD pressures are more accurately predicted than they are for the HIAD models, largely due to the nozzle locations and pointing directions. Overall, the CFD pressure coefficients were predicted within 0.2 of the steady pressure measurements for all blowing models, with smaller discrepancies at higher HIAD thrust, and larger discrepancies at lower HIAD CobraMRV thrust. All HIAD models were predicted to have a gradually decreasing axial force coefficient as the total thrust increases, in agreement with available pressure sensitive paint data. On models with canted nozzles or with nozzles further from the nose, the force coefficient was slightly higher for a given thrust. On the CobraMRV model, the CFD also shows consistent results between solvers and follows trends revealed in the data; the aerodynamic force coefficient remains near the non-blowing value at a tunnel Mach number of 2.4 regardless of thrust, and increases above that level at a Mach number of 3.5, consistent with the discrete pressure data. CFD analysis at tunnel and flight conditions will continue as flight system designs concepts mature.

Supersonic Retropropulsion↗