Engineering topics

Frassinetti, L. (ORCID:0000000295464494)

Publications and source records attributed to Frassinetti, L. (ORCID:0000000295464494).

7 records

DOE OSTI2024

Overview of physics results from MAST upgrade towards core-pedestal-exhaust integration

Recent results from MAST Upgrade are presented, emphasising understanding the capabilities of this new device and deepening understanding of key physics issues for the operation of ITER and the design of future fusion power plants. The impact of MHD instabilities on fast ion confinement have been studied, including the first observation of fast ion losses correlated with Compressional and Global Alfvén Eigenmodes. High-performance plasma scenarios have been developed by tailoring the early plasma current ramp phase to avoid internal reconnection events, resulting in a more monotonic q profile with low central shear. The impact of m/n = 3/2, 2/1 and 1/1 modes on thermal plasma confinement and rotation profiles has been quantified, and scenarios optimised to avoid them have transiently reached values of normalised beta approaching 4.2. In pedestal and ELM physics, a maximum pedestal top temperature of ~350 eV has been achieved, exceeding the value achieved on MAST at similar heating power. Mitigation of type-I ELMs with n = 1 RMPs has been observed. Studies of plasma exhaust have concentrated on comparing conventional and Super-X divertor configurations, while X-point target, X-divertor and snowflake configurations have been developed and studied in parallel. In L-mode discharges, the separatrix density required to detach the outer divertors is approximately a factor 2 lower in the Super-X than the conventional configuration, in agreement with simulations. Detailed analysis of spectroscopy data from studies of the Super-X configuration reveal the importance of including plasma-molecule interactions and D 2 Fulcher band emission to properly quantify the rates of ionisation, plasma-molecule interactions and volumetric recombination processes governing divertor detachment. In H-mode with conventional and Super-X configurations, the outer divertors are attached in the former and detached in the latter with no impact on core or pedestal confinement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Density pedestal prediction model for tokamak plasmas

Abstract A model for the pedestal density prediction based on neutral penetration combined with pedestal transport is presented. The model is tested against a pedestal database of JET-ILW Type I ELMy H-modes showing good agreement over a wide range of parameters both in standalone modelling (using the experimental temperature profile) and in full Europed modelling that predicts both density and temperature pedestals simultaneously. The model is further tested for ASDEX Upgrade and MAST-U Type I ELMy H-modes and both are found to agree with the same model parameters as for JET-ILW. The JET-ILW experiment where the isotope of the main ion is varied in a D/T scan at constant gas rate and constant β N is successfully modelled as long as the separatrix density ( n e,sep ) and pedestal transport coefficient ratio ( D / χ ) are varied in accordance with the experimentally observed variation of n e,sep and the isotope dependence of D / χ found in gyrokinetic simulations. The predictions are found to be sensitive to n e,sep which is why the model is combined with an n e,sep model to predict the pedestal for the STEP fusion reactor.

Physics↗

DOE OSTI2023

L-H transition studies in tritium and deuterium–tritium campaigns at JET with Be wall and W divertor

The recent deuterium–tritium campaign in JET-ILW (DTE2) has provided a unique opportunity to study the isotope dependence of the L-H power threshold in an ITER-like wall environment (Be wall and W divertor). Here we present results from dedicated L-H transition experiments at JET-ILW, documenting the power threshold in tritium and deuterium–tritium plasmas, comparing them with the matching deuterium and hydrogen datasets. From earlier experiments in JET-ILW it is known that as plasma isotopic composition changes from deuterium, through varying deuterium/hydrogen concentrations, to pure hydrogen, the value of the line averaged density at which the threshold is minimum, ${\bar n_{{\text{e}},{\text{min}}}}$, increases, leading us to expect that ${\bar n_{{\text{e}},{\text{min}}}}$(T) < ${\bar n_{{\text{e}},{\text{min}}}}$(DT) < ${\bar n_{{\text{e}},{\text{min}}}}$(D) < ${\bar n_{{\text{e}},{\text{min}}}}$(H). The new power threshold data confirms these expectations in most cases, with the corresponding ordering of the minimum power thresholds. We present a comparison of this data to power threshold scalings, used for extrapolation to future devices such as ITER and DEMO.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Parameter dependencies of the separatrix density in low triangularity L-mode and H-mode JET-ILW plasmas

Abstract The midplane electron separatrix density, n e,sep , in JET-ILW L-mode and H-mode low triangularity deuterium fuelled plasmas exhibits a strong explicit dependence on the averaged outer divertor target electron temperature, n e,sep ∼ T e,ot −1/2 . This dependence is reproduced by analytic reversed two point model (rev-2PM), and arises from parallel pressure balance, as well as the ratio of the power and momentum volumetric loss factors, (1 − f cooling )/(1 − f mom-loss ). Quantifying the influence of the (1 − f cooling ) and (1 − f mom-loss ) loss factors on n e,sep has been enabled by measurement estimates of these quantities from L-mode density (fueling) ramps in the outer horizontal, VH(C), and vertical target, VV, divertor configurations. Rev-2PM n e,sep estimates from the extended H-mode and more limited L-mode datasets are recovered to within ±25% of the measurements, with a scaling factor applied to account for use of T e,ot , an averaged quantity, rather than flux tube resolved target values. Both the (1 − f cooling ) and (1 − f mom-loss ) trends and recovery of n e,sep using the rev-2PM formatting are reproduced in EDGE2D-EIRENE L-mode-like and H-mode-like density scan simulations. The general lack of a divertor configuration effect in the JET-ILW n e,sep trends can be attributed to a significant influence of main chamber recycling, which has been shown in the EDGE2D-EIRENE results to moderate n e,sep with respect to changes in divertor neutral leakage imposed by changes in the divertor configuration. The unified n e,sep vs T e,ot trends can, however, be broken if large modifications to the divertor geometry (e.g. complete removal of the outer divertor baffle structure) are introduced in the model. The more pronounced high-field side high density region formation in the VH(C) configuration with reduced clearance to the separatrix does not appear to have a significant influence on the outer midplane separatrix and pedestal parameters when mapped to T e,ot , although conditions at the inner midplane could not be assessed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Validation of IMEP on Alcator C-Mod and JET-ILW ELMy H-mode plasmas

Abstract The recently developed integrated model based on engineering parameters (IMEP) (Luda et al 2020 Nucl. Fusion 61 126048; Luda et al 2021 Nucl. Fusion 60 036023), so far validated on ASDEX Upgrade, has been tested on a database of 3 Alcator C-Mod and 55 JET-ILW ELMy (type I) H-mode stationary phases. The empirical pedestal transport model included in IMEP, consisting now of imposing a fixed value of R < ∇ T e > / T e , t o p = − 82.5 , allows an accurate prediction of the pedestal top temperature (when the pedestal top density is fixed to the experimental measurements) across these three machines with different sizes, when the pedestal is peeling–ballooning (PB) limited. Cases far from the ideal PB boundary, corresponding to high edge Spitzer resistivity, are instead strongly overpredicted by IMEP. A comparison between the predictions of Europed and IMEP for a subset of JET-ILW cases shows that IMEP can more accurately reproduce the experimental pedestal width. This allows IMEP to better capture profile effects on the pedestal stability, and therefore to correctly describe the negative effect of fueling on the pedestal pressure for PB limited cases. A strong correlation between the separatrix density and the fueling rate has been identified for a subset of JET-ILW cases, when taking into account different divertor configurations. Overall, these promising results encourage further developments of integrated models to obtain reliable predictions of pedestal and global confinement using only engineering parameters for present and future machines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

The role of ETG modes in JET–ILW pedestals with varying levels of power and fuelling

Abstract We present the results of GENE gyrokinetic calculations based on a series of JET–ITER-like-wall (ILW) type I ELMy H-mode discharges operating with similar experimental inputs but at different levels of power and gas fuelling. We show that turbulence due to electron-temperature-gradient (ETGs) modes produces a significant amount of heat flux in four JET–ILW discharges, and, when combined with neoclassical simulations, is able to reproduce the experimental heat flux for the two low gas pulses. The simulations plausibly reproduce the high-gas heat fluxes as well, although power balance analysis is complicated by short ELM cycles. By independently varying the normalised temperature gradients ( ω T e ) and normalised density gradients ( ω n e ) around their experimental values, we demonstrate that it is the ratio of these two quantities η e = ω T e / ω n e that determines the location of the peak in the ETG growth rate and heat flux spectra. The heat flux increases rapidly as η e increases above the experimental point, suggesting that ETGs limit the temperature gradient in these pulses. When quantities are normalised using the minor radius, only increases in ω T e produce appreciable increases in the ETG growth rates, as well as the largest increases in turbulent heat flux which follow scalings similar to that of critical balance theory. However, when the heat flux is normalised to the electron gyro-Bohm heat flux using the temperature gradient scale length L T e , it follows a linear trend in correspondence with previous work by different authors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Microtearing modes as the source of magnetic fluctuations in the JET pedestal

Abstract We report on a detailed study of magnetic fluctuations in the JET pedestal, employing basic theoretical considerations, gyrokinetic simulations, and experimental fluctuation data to establish the physical basis for their origin, role, and distinctive characteristics. We demonstrate quantitative agreement between gyrokinetic simulations of microtearing modes (MTMs) and two magnetic frequency bands with corresponding toroidal mode numbers n = 4 and 8. Such disparate fluctuation scales, with substantial gaps between toroidal mode numbers, are commonly observed in pedestal fluctuations. Here we provide a clear explanation, namely the alignment of the relevant rational surfaces (and not others) with the peak in the ω * profile, which is localized in the steep gradient region of the pedestal. We demonstrate that a global treatment is required to capture this effect. Nonlinear simulations suggest that the MTM fluctuations produce experimentally-relevant transport levels and saturate by relaxing the background electron temperature gradient, slightly downshifting the fluctuation frequencies from the linear predictions. Scans in collisionality are compared with a simple MTM dispersion relation. At the experimental points considered, MTM growth rates can either increase or decrease with collision frequency depending on the parameters thus defying any simple characterization of collisionality dependence.

Physics↗