Search NASA⌕ Search

Engineering topics

Fredrickson, Guy L.

Publications and source records attributed to Fredrickson, Guy L..

At least 19 records

Chlorination of HALEU regulus casting dross

A scoping study was performed for chlorinating dross formed during uranium casting operations. Here, the purpose is to minimize the losses of uranium to dross wastes. The dross is primarily a mixture of uranium metal and uranium oxide with a minor fraction of crucible and crucible coating materials. The reaction chemistries were performed in a carrier salt of LiCl-KCl eutectic at 500 °C. The addition of FeCl 2 chlorinated the uranium metal to UCl 3 , by reducing the FeCl 2 to iron metal. After the uranium metal was chlorinated, zirconium metal was added to the salt. The residual FeCl 2 chlorinated the zirconium metal to ZrCl 4 , by reducing the FeCl 2 to iron metal. In turn, the ZrCl 4 chlorinated the uranium oxide to UCl 3 , by converting the ZrCl 4 to zirconium oxide. The effectiveness of the chlorination reactions was qualitatively verified by cyclic voltammograms that indicated the presence or absence of FeCl 2 and UCl 3 in the salt.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synthesis and characterization of super occluded LiCl-KCl in zeolite-4A as a chloride salt waste form intermediate

Here, this paper reports the hygroscopic properties of eutectic LiCl-KCl after absorption into zeolite-4A, up to salt loadings of 75 wt%. Samples of the salt occluded zeolite were hydrated in a humidity chamber at constant temperature and relative humidity for up to 100 h. At up to 45 wt% salt loading, the un-occluded phase of salt consisted primarily of NaCl, which forms when the Na + ions present in the zeolite framework exchange with Li + and K + ions from the eutectic LiCl-KCl. This results in minimal water absorption and corrosion of contacted stainless steel. At greater than 45 wt% salt loading, water absorption and corrosion progressively worsened. The mixture has a significant amount of excess LiCl-KCl, making it highly hygroscopic. This study reveals an option for the intermediate treatment of waste salt from spent nuclear fuel electrorefiners that could facilitate it to be stored in a non-inert atmosphere for extended periods of time before final conversion into a permanent waste form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

History and status of spent fuel treatment at the INL Fuel Conditioning Facility

Experimental Breeder Reactor II (EBR-II) had an illustrious operational history from 1964 to 1994 as one of the first sodium-cooled fast reactors to use sodium-bonded metallic driver fuels and blankets. EBR-II was a testbed for fuel development and reactor design principles. Following shutdown, it was decided to use electrometallurgical methods to treat the spent fuel and blanket materials for final disposition. Here, this paper provides a brief history of U.S. liquid metal cooled reactor development with emphasis on EBR-II, and a technical description of the electrometallurgical methods.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Methods and systems for aluminum electroplating

Systems and methods for coating a metallic component are provided. In one embodiment, a metallic coating may be disposed in a plating bath comprising AlBr3. The metallic coating may be coupled with, or configured as, a working electrode. A counter electrode formed of aluminum may be disposed within the plating bath. An electric current may be applied between the two electrodes resulting in the electrodeposition of aluminum on the metallic component. In one particular embodiment, the plating bath may include LiBr, KBr and CsBr, with AlBr3 being present in an amount of approximately 80 percent or greater by weight. Various types of metals may be coated with aluminum using embodiments of the present disclosure. Additionally, the methods and systems described herein are amenable to coating of complex geometries.

Tripathy, Prabhat K.↗

Electrochemical measurement and analysis of YCl 3 , ScCl 3 , GdCl 3 and MgCl 2 in molten eutectic LiCl-KCl

For this work, electrochemical measurements of YCl 3 , ScCl 3 , GdCl 3 and MgCl 2 were obtained in molten LiCl-KCl eutectic at 773 K using a three-electrode configuration. Tungsten rods were used as the working and counter electrodes. Two quasi- and one reference electrode(s) (glassy carbon, nickel wire, and Ni/NiO) were used to collect electrochemical measurements of the analyte salts. Cyclic voltammetry data were analyzed to calculate values of diffusion coefficient, exchange current density, and charge transfer resistance and were determined to be on the order of 10 –5 cm 2 s –1 , 10 –2 A cm –2 , and 10 0 Ω; respectively. In general, the values of diffusion coefficients were found to be consistent with those reported of high-temperature molten salts. Relatively large values of exchange current density corresponded with smaller values of charge transfer resistance. These values were found to be reasonable in comparison to results available in the literature. The measured cyclic voltammograms were normalized with respect to both lithium reduction and chloride ion oxidation potentials. Such a normalization technique is effective for comparing experimentally obtained cyclic voltammetry data to those that have been published. An analysis of experimentally obtained results indicates the relation of electrode reactions (e.g., differences of reduction potentials) are independent of the choice of reference electrode. Additionally, the choice of reference electrode did not affect the electrochemical window, exchange current density, or diffusion coefficient values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Deliquescence of Eutectic LiCl-KCl Diluted with NaCl for Interim Waste Salt Storage

Molten eutectic LiCl-KCl salt is a widely used electrolyte for electrorefining uranium from spent nuclear fuel. Due to the hygroscopic nature of this salt, such operations must be performed under controlled atmospheric conditions, and waste salts require careful storage to avoid deliquescence and corrosion of container materials. This study investigated a potential processing path for reducing the degree of deliquescence through dilution to varying extents with NaCl. Here, the hydration behavior of LiCl-KCl salts diluted with NaCl was evaluated in terms of mass gain due to water absorption, degree of deliquescence (including first appearances of standing water), and evidence of corrosion to stainless steel containers in a humid air environment (40°C, 20% relative humidity). In this humid air environment, pure eutectic LiCl-KCl exhibited a 50 mass % increase due to water absorption and showed evidence of standing water after 24 h. Waste salt diluted with NaCl required loadings of 89 mass % NaCl in order to prevent deliquescence and exhibited a 3 mass % increase due to water absorption. After periodic observation for 48 h, standing water was observed near all ingots with the exception of the 89 mass % NaCl samples. Dilution with 89% NaCl was also found to reduce evidence of corrosion when stored in stainless steel crucibles. While dilution with NaCl greatly decreases steady-state hydration, the storage volume is increased ~10× through this procedure.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nuclear Fuels and Reprocessing Technologies: A U.S. Perspective

Reprocessing and/or waste management issues are of concern to the “back end” of the nuclear fuel cycle. Of course, there are a great many “nuclear fuel cycle” scenarios to consider; if not in practice, then at least in theory. The simplest conceptually is the “once through” fuel cycle in which the spent fuel is discarded. The more complex fuel cycle scenarios involve reprocessing spent nuclear fuels and a family of nuclear reactor technologies to accommodate burning and breeding for various military and commercial needs. Therefore, the selection of a specific “fuel cycle” is what ultimately imposes the engineering requirements of the reprocessing and waste management technologies. No one part is independent of the other parts in a fuel cycle flowsheet; all parts are fully integrated. This paper presents a summary of radiochemical processes, nuclear reactor technologies, nuclear fuel types, and the reprocessing technologies that serve the different nuclear fuel types. Comprehending how this series of topics are related to each other is a prerequisite to understanding the requirements of any reprocessing strategy. The summary materials presented here are selective, as opposed to comprehensive. More detailed information on any one subject can be found in the reference materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Liquid cadmium cathode performance model based on the equilibrium behaviors of U and Pu in molten LiCl–KCl/Cd system at 500°C

The liquid cadmium cathode is a pyroprocessing technology used for the recovery of group actinide metals from the molten chloride salts that support uranium electrorefining. This article presents a model for the performance of a liquid cadmium cathode based on considerations of salt/alloy equilibrium thermodynamics, Cd-U-Pu phase diagram behaviors, and mass balance constraints. In conclusion, the model demonstrates how the salt/cadmium system responds as incremental additions of uranium are made to the liquid cadmium cathode.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal analysis of projected molten salt compositions during FFTF and EBR-II used nuclear fuel processing

This work studies the change in liquidus temperature of the salt used in the Mk-IV electrorefiner at the Idaho National Laboratory during processing campaigns of sodium-bonded driver fuels from Experimental Breeder Reactor II and the Fast Flux Test Facility reactor. Modeling and Simulation Tool for Electrochemical Recycling Systems (MASTERS), an INL proprietary pyroprocessing flowsheet simulation tool, was used to simulate the processing campaigns and determine the resulting composition changes of the Mark-IV electrorefiner salt. Surrogate salt samples simulating the Mk-IV electrorefiner salt during the fuel processing campaigns were prepared, and the thermal properties were measured via differential scanning calorimetry. Results from this study indicate that after processing approximately 2,150 kg of uranium metal from used fuel, the liquidus temperature of the molten salt exceeds 520°C, which is a significant increase from 352°C (the melting temperature of eutectic LiCl-KCl). It was also discovered that the liquidus temperature is strongly dependent on the amount of NaCl accumulating in the Mk-IV electrorefiner salt. Thus, the assessment of the liquidus temperature during the subsequent fuel processing campaigns can be simplified by considering the ternary LiCl-KCl-NaCl system only.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Review—Electrochemical Measurements in Molten Salt Systems: A Guide and Perspective

Practical information is provided on electrochemical measurements in molten salt systems. The emphasis is on chloride and fluoride systems, but the principles are applicable to any high temperature molten salt or molten oxide electrolyte system. Considerations are given to topics such as the functionality of electrochemical measurement equipment, reference electrodes, materials selection and chemical compatibility, interpretation of electrochemical measurement signals, molten salt properties, and laboratory practices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molten Salt Reactor Salt Processing – Technology Status

This report presents a summary of 752 citations related to molten salt reactor development at Oak Ridge National Laboratory (ORNL). This effort was initiated with a focused purpose of locating technical information related to the chemical processing of fluoride salts to support the Th-232/U-233 fuel-cycle molten-salt breeder reactor. However, it soon became apparent that technical information on chemical processing was spread throughout numerous reports spanning decades of time. Therefore, the search effort was broadened to include any information deemed relevant to MSR development at ORNL. In addition, this report provides an overview of the engineering requirements of a chemical processing plant to support the Th-232/U-233 fuel-cycle molten salt breeder reactor (MSBR). This includes descriptions of the unit operations and flowsheets development at ORNL. The transition from the two-fluid MSBR to the single-fluid MSBR was largely due to the development of new separations technologies for the management of uranium, protactinium, and fission products in fluoride molten salts. The development and refinement of chemical processing plant flowsheets continued throughout the entirety of the MSBR program at ORNL. A great deal of experimental and theoretical work was performed in support of the unit operations and flowsheets described here.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of undissolved anode materials of Mark-IV electrorefiner

The Mark-IV electrorefiner contains a molten-salt/molten-cadmium system for electrorefining uranium. The anode basket is loaded with chopped sodium-bonded metallic driver fuel. For the present investigation, the bulk of the fuel was U-10Zr binary alloy. The undissolved anode materials after electrorefining are sampled for chemical analysis. The estimation of the undissolved anode materials based on individual chemical analysis results are challenging due to inherently high sampling errors associated with heterogeneous undissolved material compositions. Investigation of chemical analysis data as a whole reveals noticeable trends in the compositions of the primary phases and materials. Based upon this observation, we propose a methodology for accounting the primary phases relying on the measurement of the total anode mass only. Furthermore, the methodology is based on an empirical model explaining the mass of the undissolved anode materials constructed from historical anode material analysis data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Uranium exchange kinetics in a molten LiCl-KCl/Cd system at 500 °C

A dissolution experiment is performed in order to examine the kinetics of uranium isotope equilibration in a molten salt and cadmium system. The salt contains a solute concentration of UCl 3 in LiCl-KCl eutectic and the cadmium contained dissolved uranium at 500 °C. A small piece of high enriched uranium is introduced to the cadmium, which perturbs the equilibrium with respect to the uranium enrichment of the salt and cadmium phases. The series of salt and cadmium samples trace how the enrichment of the two phases reach equilibrium (in the absence of a chemical driving force) over the course of approximately 24 h. Here, a model linking dissolution and isotope exchange kinetics is developed to track the evolution of uranium isotope composition. With the assumption of unaccounted salt mass incurred from the dated sample reporting practice, the model explains the trend of the measured uranium isotope composition well.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis and modeling of the equilibrium behaviors of U and Pu in molten LiCl-KCl/Cd system at 500 °C

In the field of pyroprocessing of used nuclear fuels, liquid cadmium is applied in different ways to recover transuranics from molten salt, while effecting some degree of separations between transuranics and lanthanides. In this work, a model of the separation performance between uranium and plutonium across the phase boundary between molten salt and liquid cadmium is presented. The salt is the LiCl-KCl eutectic with solute concentrations of UCl 3 and PuCl 3 . The cadmium is the liquid cadmium phase field from the Cd-U-Pu ternary alloy system. Lastly, the model used to describe the behavior of uranium and plutonium in the salt/cadmium system is applied to describe the behavior of plutonium and lanthanide in the salt/cadmium system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Experimental Study of Codeposition Electrochemistry Using Mixtures of ScCl 3 and YCl 3 in LiCl-KCl Eutectic Salt at 500°C

Cyclic voltammetry and chronopotentiometry tests were applied to molten LiCl-KCl eutectic at 500 °C including amounts of ScCl 3 and YCl 3 . The purpose of the testing was to observe the effect of applied electrical current on the codeposition of scandium and yttrium, which were chosen as surrogate elements for uranium and plutonium, respectively. Features of the work were to vary the concentration of ScCl 3 (at relatively low concentrations) as well as varying the applied current, all with a fixed concentration of YCl 3 . Results of the experiments could provide insight of uranium electrorefining and may provide evidence, which suggests the electrorefiner could be operated at lower UCl 3 concentration whereby codeposition (U and Pu) could be more effectively controlled.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Final Technical Report on Fluoride Salt Study

This report fulfills the Level 3 Milestone No. M3FT-15IN0311022 titled, “Uranium Electrorefining Using Fluoride Salt” within the Department of Energy (DOE) Work Package No. FT-15IN031102 titled, “U/TRU Codeposition and Fluoride Salt Studies – INL”. This work package falls under the Fuel Cycle Research and Development (FCR&D) Materials Recovery and Waste Form Development (MRWFD) Program 1.02.03.11 titled “Domestic Echem”. The electrorefining of uranium in a LiF-NaF-KF, or FLiNaK, salt containing UF 3 has been performed. Several gram-scale electrodeposits of uranium were collected exhibiting a dendritic morphology similar to uranium electrorefining in chloride salts. Additionally, cyclic voltammetry experiments have been performed at 773 K in FLiNaK-UF 4 , FLiNaK-UF 3 , and FLiNaK-UF 3 -LaF 3 salt mixtures to analyze the feasibility of electrorefining uranium in the FLiNaK salt containing lanthanides. Results are promising, showing a 0.48 V potential window between uranium and lanthanum depositions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Alkali Bromide Salts for Potential Pyrochemical Applications

Transient techniques were employed to study the electrochemical behavior, reduction mechanism and transport properties of REBr3 (RE - La, Nd and Gd) in pure LiBr, LiBr-KBr (eutectic) and LiBr-KBr-CsBr (eutectic) melts. Gd(III) showed a reversible single step soluble-insoluble exchange phenomenon in LiBr melt at 973K. Although La (III), Nd(III) and Gd(III) ions showed reversible behavior in eutectic LiBr-KBr melts, these ions showed a combination of temperature dependent reversible and pseudo-reversible behavior. While both La(III) and Gd(III) showed one step reduction, the reduction of Nd(III) was observed to be a two step process. La metal could be electrodeposited from the ternary electrolyte at a temperature of 673K. Various electrochemical measurements suggest that both binary and ternary bromide melts can potentially be used to electrodeposit high purity RE metals at comparatively lower operating temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗