Search NASA⌕ Search

Engineering topics

Fridman, E.

Publications and source records attributed to Fridman, E..

Coupled neutronic-thermal-hydraulic simulations of the European SFR core

Within the European SFR (Sodium-cooled Fast Reactor) - Safety Measures Assessment and Research Tools (ESFR-SMART) project, steady-state coupled simulation of the ESFR core has been performed using several core analysis packages, with the objective of quantifying the coupling effect. Focus is on the fuel Doppler effect and coolant expansion effect. Standalone neutronics calculations in TRACE/PARCS (PSI), DYN3D (HZDR) and WIMS (Jacobs) showed superb agreement with the reference Serpent power distribution (root mean square - rms discrepancies of 1.3%, 1.5% and 0.7% respectively). Results for COUNTHER (CIEMAT) were also in reasonable agreement, but with a somewhat higher discrepancy of 3.7%. Temperature distributions from thermal-hydraulic calculations were also compared and are found to be in good agreement. The effect of Doppler and coolant density feedback on core power distribution was predicted by TRACE/PARCS, DYN3D and WIMS to be between 0.4% and 0.8% rms difference in assembly powers. Reactivity coefficients for perturbations in the inlet temperature, flow rate and core power were shown to be negative for these three codes, with values of roughly -0.5 pcm/C. degree, -0.3 pcm/C. degree and -3.5 pcm/C. degree respectively. A preliminary investigation of differential thermal expansion effects indicates that this may have a significant effect on core power distribution of a few %, greater than anticipated a priori and may warrant inclusion in coupled core analysis to ensure the accurate calculation of power distributions. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Comparison of Serpent and HELIOS-2 as applied for the PWR few-group cross section generation

This paper discusses recent modifications to the Serpent Monte Carlo code methodology and related to the calculation of few-group diffusion coefficients and reflector discontinuity factors The new methods were assessed in the following manner. First, few-group homogenized cross sections calculated by Serpent for a reference PWR core were compared with those generated 1 commercial deterministic lattice transport code HELIOS-2. Second, Serpent and HELIOS-2 fe group cross section sets were later employed by nodal diffusion code DYN3D for the modeling the reference PWR core. Finally, the nodal diffusion results obtained using the both cross section sets were compared with the full core Serpent Monte Carlo solution. The test calculations show that Serpent can calculate the parameters required for nodal analyses similar to conventional deterministic lattice codes. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Generation of SFR few-group constants using the Monte Carlo code Serpent

In this study, the Serpent Monte Carlo code was used as a tool for preparation of homogenized few-group cross sections for the nodal diffusion analysis of Sodium cooled Fast Reactor (SFR) cores. Few-group constants for two reference SFR cores were generated by Serpent and then employed by nodal diffusion code DYN3D in 2D full core calculations. The DYN3D results were verified against the references full core Serpent Monte Carlo solutions. A good agreement between the reference Monte Carlo and nodal diffusion results was observed demonstrating the feasibility of using Serpent for generation of few-group constants for the deterministic SFR analysis. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Revised methods for few-group cross sections generation in the Serpent Monte Carlo code

This paper presents new calculation methods, recently implemented in the Serpent Monte Carlo code, and related to the production of homogenized few-group constants for deterministic 3D core analysis. The new methods fall under three topics: 1) Improved treatment of neutron-multiplying scattering reactions, 2) Group constant generation in reflectors and other non-fissile regions and 3) Homogenization in leakage-corrected criticality spectrum. The methodology is demonstrated by a numerical example, comparing a deterministic nodal diffusion calculation using Serpent-generated cross sections to a reference full-core Monte Carlo simulation. It is concluded that the new methodology improves the results of the deterministic calculation, and paves the way for Monte Carlo based group constant generation. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

High conversion Th-U{sup 233} fuel assembly for current generation of PWRs

This paper presents a preliminary design of a high conversion Th-U{sup 233} fuel assembly applicable for current generation of Pressurized Water Reactor (PWRs). The considered fuel assembly has a typical 17 x 17 PWR lattice. However in order to increase the conversion of Th{sup 232} to U{sup 233}, the assembly was subdivided into the two regions called seed and blanket. The central seed region has a higher than blanket U{sup 233} content and acts as a neutron source for the peripheral blanket region. The latest acts as a U{sup 233} breeder. While the seed fuel pins have a standard dimensions the blanket fuel radius was increased in order to reduce the moderation and to facilitate the resonance neutron absorption in blanket Th{sup 232}. The U{sup 233} content in the seed and blanket regions was optimized to achieve maximal initial to discharged fissile inventory ratio (FIR) taking into account the target fuel cycle length of 12 months with 3-batch reloading scheme. In this study the neutronic calculations were performed on the fuel assembly level using Helios deterministic lattice transport code. The fuel cycle length and the core k{sub eff} were estimated by applying the Non Linear Reactivity Model. The applicability of the HELIOS code for the analysis of the Th-based high conversion designs was confirmed with the help of continuous-energy Monte-Carlo code SERPENT. The results of optimization studies show that for the heterogeneous seed and blanket (SB) fuel assembly the FIR of about 0.95 can be achieved. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Conceptual design of a pressure tube light water reactor with variable moderator control

This paper presents the development of innovative pressure tube light water reactor with variable moderator control. The core layout is derived from a CANDU line of reactors in general, and advanced ACR-1000 design in particular. It should be stressed however, that while some of the ACR-1000 mechanical design features are adopted, the core design basics of the reactor proposed here are completely different. First, the inter fuel channels spacing, surrounded by the calandria tank, contains a low pressure gas instead of heavy water moderator. Second, the fuel channel design features an additional/external tube (designated as moderator tube) connected to a separate moderator management system. The moderator management system is design to vary the moderator tube content from 'dry' (gas) to 'flooded' (light water filled). The dynamic variation of the moderator is a unique and very important feature of the proposed design. The moderator variation allows an implementation of the 'breed and burn' mode of operation. The 'breed and burn' mode of operation is implemented by keeping the moderator tube empty ('dry' filled with gas) during the breed part of the fuel depletion and subsequently introducing the moderator by 'flooding' the moderator tube for the 'burn' part. This paper assesses the conceptual feasibility of the proposed concept from a neutronics point of view. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A trigonal nodal SP3 method with mesh refinement capabilities - Development and verification

The neutronics model of the nodal reactor dynamics code DYN3D developed for 3D analyses of steady states and transients in Light-Water Reactors has been extended by a simplified P{sub 3} (SP{sub 3}) neutron transport option - to overcome the limitations of the diffusion approach at regions with significant anisotropy effects. To provide a method being applicable to reactors with hexagonal fuel assemblies and to furthermore allow flexible mesh refinement, the nodal SP{sub 3} method has been developed on the basis of a flux expansion in triangular-z geometry. In this paper, the derivation of the trigonal SP{sub 3} method is presented in a condensed form and a verification of the methodology on quasi-pin level is performed by means of two single-assembly test examples. The corresponding pin-wise few-group cross sections were obtained by the deterministic lattice code HELIOS. The power distributions were calculated using both the trigonal DYN3D diffusion and SP{sub 3} solver and compared to the HELIOS reference solutions. Close to regions with non-negligible flux gradients, e.g., caused by the presence of a strong absorbing material, the power distribution calculated by DYN3D-SP{sub 3} shows a significant improvement in comparison to the diffusion method. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗