Engineering topics

Fried, Laurence E.

Publications and source records attributed to Fried, Laurence E..

5 records

DOE OSTI2024

Diffraction Measurement of Reaction Products in Shock Compressed TATB on the NIF

The shock-induced reaction of high explosives to gaseous and solid reaction products is a rapid, complex process. Understanding solid reaction product structure and formation kinetics is essential in determining the high-pressure equation of state of these multicomponent systems. We use the National Ignition Facility (NIF) to shock compress ~500-µm thick pressed powder high-explosive TATB samples to 70-135 GPa and collect in situ structural data on detonation byproducts using the TARDIS X-ray diffraction diagnostic. Velocimetry is used to record the transmitted compression wave profile, which is well described by Cheetah hydrocode simulations coupled with a reactive flow model, providing strong evidence of reaction in the TATB sample. While an unambiguous determination of the product phases was not possible owing to the low signal-to-noise quality of the diffraction signal, X-ray diffraction data of the product phases formed within the first 50 ns of the reaction is most consistent with a mixture of amorphous products and crystalline hexagonal diamond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

New Nonreactive Force Field for Accurate Molecular Dynamics Simulations of TATB at Extreme Conditions

Insensitive high explosives based on TATB (1,3,5-triamino-2,4,6-trinitrobenzene) are needed in applications when safety is of paramount importance, but the basic material properties that give rise to its insensitivity are not fully understood. Molecular dynamics modeling using empirical force fields (FFs) has been the main route to characterize many complicated dynamical properties of TATB single crystal, but these FFs have not been comprehensively tested at extreme conditions typical of detonation. We collect a benchmark data set of (quasi)static TATB physical properties as determined by experiments and electronic structure calculations and apply this data set to validate four existing TATB FFs along with a new TATB FF that we develop here and denote as the CEA-LLNL-Missouri (CLM) FF. Benchmark data include vibrational spectra, the TATB crystal temperature–pressure–volume equation of state and lattice parameters, properties of TATB crystal polymorphs and transitions to the gaseous and liquid states, dimer energy landscapes, the pressure-dependent elastic tensor, and the energy landscape for inelastic deformation via sliding of TATB crystal layers. As a general assessment, we find that the two existing nonreactive FFs are more accurate in describing TATB’s physical properties compared to the two variants of the ReaxFF reactive FF considered. The new CLM FF is found to consistently yield similar or better agreement with experiments and electronic structure theory than any of the existing FF models, and it presents a distinct improvement in accurately modeling TATB elasticity and equation of state. So this work is expected to help improve the accuracy of FF-based modeling of complicated dynamic responses that ultimately govern the safety and performance characteristics of this material.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Chemical evolution in nitrogen shocked beyond the molecular stability limit

Evolution of nitrogen under shock compression up to 100 GPa is revisited via molecular dynamics simulations using a machine-learned interatomic potential. The model is shown to be capable of recovering the structure, dynamics, speciation, and kinetics in hot compressed liquid nitrogen predicted by first-principles molecular dynamics, as well as the measured principal shock Hugoniot and double shock experimental data, albeit without shock cooling. Our results indicate that a purely molecular dissociation description of nitrogen chemistry under shock compression provides an incomplete picture and that short oligomers form in non-negligible quantities. Finally, this suggests that classical models representing the shock dissociation of nitrogen as a transition to an atomic fluid need to be revised to include reversible polymerization effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Temperature-based reactive flow model for TATB plastic bonded explosives

A new reactive flow model is presented for TATB-based plastic bonded explosives, applicable to shock initiation and detonation problems of differing initial temperature. Temperature disequilibrium is assumed between unreacted explosive, material in the vicinity of compressed defects (called hot spots), and detonation products. The model incorporates temperature-dependent decomposition reaction rates. Arrhenius model parameters were derived from subscale quantum-based molecular dynamics simulations of shock-induced TATB decomposition. Further, a model of detonation carbon aggregation is incorporated, describing the late-time slow release of energy inherent to detonation in TATB-based materials. The predictive ability of the model in the shock initiation regime is tested against recent thin pulse experiments on PBX 9502. Here, the model is found to perform equally well in predicting the size effect curve of ambient, cold, and hot PBX 9502 rate sticks.

Chemistry - Chemical explosives↗

DOE OSTI2023

Enhancing the accuracy of density functional tight binding models through ChIMES many-body interaction potentials

Semi-empirical quantum models such as Density Functional Tight Binding (DFTB) are attractive methods for obtaining quantum simulation data at longer time and length scales than possible with standard approaches. However, application of these models can require lengthy effort due to the lack of a systematic approach for their development. In this work, we discuss the use of the Chebyshev Interaction Model for Efficient Simulation (ChIMES) to create rapidly parameterized DFTB models, which exhibit strong transferability due to the inclusion of many-body interactions that might otherwise be inaccurate. We apply our modeling approach to silicon polymorphs and review previous work on titanium hydride. We also review the creation of a general purpose DFTB/ChIMES model for organic molecules and compounds that approaches hybrid functional and coupled cluster accuracy with two orders of magnitude fewer parameters than similar neural network approaches. In all cases, DFTB/ChIMES yields similar accuracy to the underlying quantum method with orders of magnitude improvement in computational cost. In conclusion, our developments provide a way to create computationally efficient and highly accurate simulations over varying extreme thermodynamic conditions, where physical and chemical properties can be difficult to interrogate directly, and there is historically a significant reliance on theoretical approaches for interpretation and validation of experimental results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗