Search NASA⌕ Search

Engineering topics

Friedlander, David

Publications and source records attributed to Friedlander, David.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Lessons Learned from Inlet Integration Analysis of NASA's Low Boom Flight Demonstrator

In 2016, NASA's Aeronautics Research Mission Directorate announced the New Aviation Horizons Initiative with a goal of designing/building several X-Planes, including a Low Boom Flight Demonstrator (LBFD). That same year, NASA awarded a contract to Lockheed Martin (LM) to advance the LBFD concept through preliminary design. Several configurations of the LBFD aircraft were analyzed by both LM engineers and NASA researchers. This presentation focuses on some of the CFD simulations that were run by NASA Glenn researchers. NASA's FUN3D V13.1 code was used for all adjoint-based grid refinement studies and Spalart-Allmaras turbulence model was used during adaptation. It was found that adjoint-based grid adaptation did not accurately capture inlet performance for high speed top-aft-mounted propulsion.

Adjoint-based Grid Adaptatio↗
NASA NTRS2017

Progress Towards Understanding Fan Inlet Implications of Top-Mounted Propulsion

Computational fluid dynamic (CFD) simulations were performed on an N+2 commercial supersonic transport aircraft design that featured top-mounted propulsion. The simulations were run at take-off conditions at both 0 degrees and 8 degrees angle of attack. The results showed little separation in around the inlets with inlet performance on par with an under-the-wing configuration. The next step will be to take these results and determine the acoustic impact of the top-mounted propulsion system.

Computational Fluid Dynamics (CFD)↗
NASA NTRS2017

Relating a Jet-Surface Interaction Experiment to a Commercial Supersonic Transport Aircraft Using Numerical Simulations

Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for a commercial supersonic transport aircraft concept and experimental hardware models designed to represent the installed propulsion system of the conceptual aircraft in an upcoming test campaign. The purpose of the experiment is to determine the effects of jet-surface interactions from supersonic aircraft on airport community noise. RANS simulations of the commercial supersonic transport aircraft concept were performed to relate the representative experimental hardware to the actual aircraft. RANS screening simulations were performed on the proposed test hardware to verify that it would be free from potential rig noise and to predict the aerodynamic forces on the model hardware to assist with structural design. The simulations showed a large region of separated flow formed in a junction region of one of the experimental configurations. This was dissimilar with simulations of the aircraft and could invalidate the noise measurements. This configuration was modified and a subsequent RANS simulation showed that the size of the flow separation was greatly reduced. The aerodynamic forces found on the experimental models were found to be relatively small when compared to the expected loads from the model’s own weight.Reynolds-Averaged Navier-Stokes (RANS) simulations were completed for two configurations of a three-stream inverted velocity profile (IVP) nozzle and a baseline single-stream round nozzle (mixed-flow equivalent conditions). For the Sideline and Cutback flow conditions, while the IVP nozzles did not reduce the peak turbulent kinetic energy on the lower side of the jet plume, the IVP nozzles did significantly reduce the size of the region of peak turbulent kinetic energy when compared to the jet plume of the baseline nozzle cases. The IVP nozzle at Sideline conditions did suffer a region of separated flow from the inner stream nozzle splitter that did produce an intense, but small, region of turbulent kinetic energy in the vicinity of the nozzle exit. When viewed with the understanding that jet noise is directly related to turbulent kinetic energy, these IVP nozzle simulations show the potential to reduce noise to observers located below the nozzle. However, these RANS simulations also show that some modifications may be needed to prevent the small region of separated flow-induced turbulent kinetic energy from the inner stream nozzle splitter at Sideline conditions.

Reynolds-Averaged Navier Stokes↗
NASA NTRS2017

Relating a Jet-Surface Interaction Experiment to a Commercial Supersonic Transport Aircraft Using Numerical Simulations

NASA and industry partners desire to reintroduce commercial supersonic airliners to the air transportation system. There are a number of technical challenges that must be overcome by future commercial supersonic airliners to make them viable solutions in society. NASA is specifically concerned with the challenges of reducing boom during supersonic cruise, maximizing range, and reducing airport community noise to acceptable levels. Concepts for commercial supersonic transports, such as the concept aircraft by Lockheed Martin pictured in Figure 1, place the engine nozzles in close proximity to wing and tail surfaces. However, the effects of noise shielding and noise radiation are not fully understood for installed propulsion systems. A series of acoustic tests were conducted on the NASA Glenn Research Centers Nozzle Acoustic Test Rig (NATR) to address the challenge of reducing airport community noise, which is often dominated by jet noise. To best represent the conceptual aircraft in the acoustic tests, noise measurements were taken of the jet in close proximity of simulated aerodynamic surfaces, not simply of an isolated jet.

nozzle flow↗
NASA NTRS2015

Computational Fluid Dynamics Modeling of a Supersonic Nozzle and Integration into a Variable Cycle Engine Model

This paper covers the development of an integrated nonlinear dynamic simulation for a variable cycle turbofan engine and nozzle that can be integrated with an overall vehicle Aero-Propulso-Servo-Elastic (APSE) model. A previously developed variable cycle turbofan engine model is used for this study and is enhanced here to include variable guide vanes allowing for operation across the supersonic flight regime. The primary focus of this study is to improve the fidelity of the model's thrust response by replacing the simple choked flow equation convergent-divergent nozzle model with a MacCormack method based quasi-1D model. The dynamic response of the nozzle model using the MacCormack method is verified by comparing it against a model of the nozzle using the conservation element/solution element method. A methodology is also presented for the integration of the MacCormack nozzle model with the variable cycle engine.

Control Theory↗
NASA NTRS2014

Computational Fluid Dynamics Modeling of a Supersonic Nozzle and Integration into a Variable Cycle Engine Model

This paper covers the development of an integrated nonlinear dynamic simulation for a variable cycle turbofan engine and nozzle that can be integrated with an overall vehicle Aero-Propulso-Servo-Elastic (APSE) model. A previously developed variable cycle turbofan engine model is used for this study and is enhanced here to include variable guide vanes allowing for operation across the supersonic flight regime. The primary focus of this study is to improve the fidelity of the model's thrust response by replacing the simple choked flow equation convergent-divergent nozzle model with a MacCormack method based quasi-1D model. The dynamic response of the nozzle model using the MacCormack method is verified by comparing it against a model of the nozzle using the conservation element/solution element method. A methodology is also presented for the integration of the MacCormack nozzle model with the variable cycle engine.

Thrust↗
NASA NTRS1990

An expert system based software sizing tool, phase 2

A software tool was developed for predicting the size of a future computer program at an early stage in its development. The system is intended to enable a user who is not expert in Software Engineering to estimate software size in lines of source code with an accuracy similar to that of an expert, based on the program's functional specifications. The project was planned as a knowledge based system with a field prototype as the goal of Phase 2 and a commercial system planned for Phase 3. The researchers used techniques from Artificial Intelligence and knowledge from human experts and existing software from NASA's COSMIC database. They devised a classification scheme for the software specifications, and a small set of generic software components that represent complexity and apply to large classes of programs. The specifications are converted to generic components by a set of rules and the generic components are input to a nonlinear sizing function which makes the final prediction. The system developed for this project predicted code sizes from the database with a bias factor of 1.06 and a fluctuation factor of 1.77, an accuracy similar to that of human experts but without their significant optimistic bias.

Friedlander, David↗