Search NASA⌕ Search

Engineering topics

Friedmann, P. P.

Publications and source records attributed to Friedmann, P. P..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Aeroelastic Analysis of a Trimmed Generic Hypersonic Vehicle

The aeroelastic equations of motion governing a hypersonic vehicle in free flight are derived. The equations of motion for a translating and rotating flexible body using Lagrange's equations in terms of quasi-coordinates are presented. These equations are simplified for the case of a vehicle with pitch and plunge rigid body degrees of freedom and small elastic displacements. The displacements are approximated by a truncated series of the unrestrained mode shapes, which are obtained using equivalent plate theory. Subsequently, the nonlinear equations of motion are linearized about the trim state, which is obtained using a rigid body trim model and steady hypersonic aerodynamics. The appropriate flutter derivatives are calculated from piston theory. Results describing mode shapes, trim behavior, and aeroelastic stability of a generic hypersonic vehicle are presented.

Nydick, I.↗
NASA NTRS1995

Aeroelasticity and structural optimization of composite helicopter rotor blades with swept tips

This report describes the development of an aeroelastic analysis capability for composite helicopter rotor blades with straight and swept tips, and its application to the simulation of helicopter vibration reduction through structural optimization. A new aeroelastic model is developed in this study which is suitable for composite rotor blades with swept tips in hover and in forward flight. The hingeless blade is modeled by beam type finite elements. A single finite element is used to model the swept tip. Arbitrary cross-sectional shape, generally anisotropic material behavior, transverse shears and out-of-plane warping are included in the blade model. The nonlinear equations of motion, derived using Hamilton's principle, are based on a moderate deflection theory. Composite blade cross-sectbnal properties are calculated by a separate linear, two-dimensional cross section analysis. The aerodynamic loads are obtained from quasi-steady, incompressible aerodynamics, based on an implicit formulation. The trim and steady state blade aeroelastic response are solved in a fully coupled manner. In forward flight, where the blade equations of motion are periodic, the coupled trim-aeroelastic response solution is obtained from the harmonic balance method. Subsequently, the periodic system is linearized about the steady state response, and its stability is determined from Floquet theory.

Yuan, K. A.↗
NASA NTRS1994

Vibration reduction in helicopter rotors using an actively controlled partial span trailing edge flap located on the blade

This report describes an analytical study of vibration reduction in a four-bladed helicopter rotor using an actively controlled, partial span, trailing edge flap located on the blade. The vibration reduction produced by the actively controlled flap (ACF) is compared with that obtained using individual blade control (IBC), in which the entire blade is oscillated in pitch. For both cases a deterministic feedback controller is implemented to reduce the 4/rev hub loads. For all cases considered, the ACF produced vibration reduction comparable with that obtained using IBC, but consumed only 10-30% of the power required to implement IBC. A careful parametric study is conducted to determine the influence of blade torsional stiffness, spanwise location of the control flap, and hinge moment correction on the vibration reduction characteristics of the ACF. The results clearly demonstrate the feasibility of this new approach to vibration reduction. It should be emphasized than the ACF, used together with a conventional swashplate, is completely decoupled from the primary flight control system and thus it has no influence on the airworthiness of the helicopter. This attribute is potentially a significant advantage when compared to IBC.

Millott, T. A.↗
NASA NTRS1993

A new sensitivity analysis for structural optimization of composite rotor blades

This paper presents a detailed mathematical derivation of the sensitivity derivatives for the structural dynamic, aeroelastic stability and response characteristics of a rotor blade in hover and forward flight. The formulation is denoted by the term semianalytical approach, because certain derivatives have to be evaluated by a finite difference scheme. Using the present formulation, sensitivity derivatives for the structural dynamic and aeroelastic stability characteristics, were evaluated for both isotropic and composite rotor blades. Based on the results, useful conclusions are obtained regarding the relative merits of the semi-analytical approach, for calculating sensitivity derivatives, when compared to a pure finite difference approach.

Venkatesan, C.↗
NASA NTRS1992

Vibration reduction in helicopter rotors using an active control surface located on the blade

A feasibility study of vibration reduction in a four-bladed helicopter rotor using individual blade control (IBC), which is implemented by an individually controlled aerodynamic surface located on each blade, is presented. For this exploratory study, a simple offset-hinged spring restrained model of the blade is used with fully coupled flap-lag-torsional dynamics for each blade. Deterministic controllers based on local and global system models are implemented to reduce 4/rev hub loads using both an actively controlled aerodynamic surface on each blade as well as conventional IBC, where the complete blade undergoes cyclic pitch change. The effectiveness of the two approaches for simultaneous reduction of the 4/rev hub shears and hub moments is compared. Conventional IBC requires considerably more power to achieve approximately the same level of vibration reduction as that obtained by implementing IBC using an active control surface located on the outboard segment of the blade. The effect of blade torsional flexibility on the vibration reduction effectiveness of the actively controlled surface was also considered and it was found that this parameter has a very substantial influence.

Millott, T. A.↗
NASA NTRS1992

Development of a structural optimization capability for the aeroelastic tailoring of composite rotor blades with straight and swept tips

This paper describes the development of a new structural optimization capability aimed at the aeroelastic tailoring of composite rotor blades with straight and swept tips. The primary objective is to reduce vibration levels in forward flight without diminishing the aeroelastic stability margins of the blade. In the course of this research activity a number of complicated tasks have been addressed: (1) development of a new, aeroelastic stability and response analysis; (2) formulation of a new comprehensive sensitive analysis, which facilitates the generation of the appropriate approximations for the objective and the constraints; (3) physical understanding of the new model and, in particular, determination of its potential for aeroelastic tailoring, and (4) combination of the newly developed analysis capability, the sensitivity derivatives and the optimizer into a comprehensive optimization capability. The first three tasks have been completed and the fourth task is in progress.

Friedmann, P. P.↗
NASA NTRS1991

Helicopter air resonance modeling and suppression using active control

A coupled rotor/fuselage helicopter analysis with the important effects of blade torsional flexibility, unsteady aerodynamics, and forward flight is presented. Using this mathematical model, a nominal configuration is selected with an air resonance instability throughout most of its flight envelope. A multivariable compensator is then designed using two swashplate inputs and a single-body roll rate measurement. The controller design is based on the linear quadratic Gaussian technique and the loop transfer recovery method. The controller is shown to suppress the air resonance instability throughout a wide range of helicopter loading conditions and forward flight speeds.

Takahashi, M. D.↗
NASA NTRS1991

Coupled rotor-fuselage vibration reduction with multiple frequency blade pitch control

A nonlinear coupled rotor/flexible fuselage analysis has been developed and used to study the effects of higher harmonic blade pitch control on the vibratory hub loads and fuselage acceleration levels. Previous results, obtained with this model have shown that conventional higher harmonic control (HHC) inputs aimed at hub shear reduction cause an increase in the fuselage accelerations and vice-versa. It was also found that for simultaneous reduction of hub shears and fuselage accelerations, a pitch input representing a combination of two higher harmonic components of different frequencies was needed. Subsequently, it was found that this input could not be implemented through a conventional swashplate. This paper corrects a mistake originally made in the representation of the multiple frequency pitch input and shows that such a pitch input can be only implemented in the rotating reference frame. A rigorous mathematical solution is found, for the pitch input in the rotating reference frame, which produces simultaneous reduction of hub shears and fuselage acceleration. New insight on vibration reduction in coupled rotor/fuselage systems is obtained from the sensitivity of hub shears to the frequency and amplitude of the open loop HHC signal in the rotating reference frame. Finally the role of fuselage flexibility in this class of problems is determined.

Papavassiliou, I.↗
NASA NTRS1991

Coupled rotor-flexible fuselage vibration reduction using open loop higher harmonic control

A fundamental study of vibration prediction and vibration reduction in helicopters using active controls was performed. The nonlinear equations of motion for a coupled rotor/flexible fuselage system have been derived using computer algebra on a special purpose symbolic computer facility. The trim state and vibratory response of the helicopter are obtained in a single pass by applying the harmonic balance technique and simultaneously satisfying the trim and the vibratory response of the helicopter for all rotor and fuselage degrees of freedom. The influence of the fuselage flexibility on the vibratory response is studied. It is shown that the conventional single frequency higher harmonic control is capable of reducing either the hub loads or only the fuselage vibrations but not both simultaneously. It is demonstrated that for simultaneous reduction of hub shears and fuselae vibrations a new scheme called multiple higher harmonic control is required.

Papavassiliou, I.↗
NASA NTRS1991

Free and forced response of nearly periodic multi-span beams and multi-bay trusses

The influence of several effects on mode localization in free-free multispan beams is investigated. Finite-element methods are used to study localization as a function of Timoshenko beam effects, imperfection strength, coupling strength, and imperfection type. The multispan beam study is conducted with random realizations of a forty-span free-free beam. In addition, free and forced response of free-free trusses and frames is investigated. Results indicate that, for the trusses and frames considered, the dynamic behavior can be approximated by continuum modeling approaches for only the lowest few global modes. Also, for reasonable values of modal damping, localized modes play a subtle role in the overall structural response.

Lust, S. D.↗
NASA NTRS1990

A study of coupled rotor-fuselage vibration with higher harmonic control using a symbolic computing facility

A fundamental study of vibration prediction and vibration reduction in helicopters using active controls was performed. The nonlinear equations of motion for a coupled rotor/flexible fuselage system have been derived using computer algebra on a special purpose symbolic computing facility. The details of the derivation using the MACSYMA program are described. The trim state and vibratory response of the helicopter are obtained in a single pass by applying the harmonic balance technique and simultaneously satisfying the trim and the vibratory response of the helicopter for all rotor and fuselage degrees of freedom. The influence of the fuselage flexibility on the vibratory response is studied. It is shown that the conventional single frequency higher harmonic control (HHC) capable of reducing either the hub loads or only the fuselage vibrations but not both simultaneously. It is demonstrated that for simultaneous reduction of hub shears and fuselage vibrations a new scheme called multiple higher harmonic control (MHHC) is required. The fundamental aspects of this scheme and its uniqueness are described in detail, providing new insight on vibration reduction in helicopters using HHC.

Papavassiliou, I.↗
NASA NTRS1990

Mode localization in multi-span beams

The influence of numerous effects on mode localization in multi-span beams is investigated. Finite-element methods are used to study localization as a function of: Timoshenko beam effects; beam end conditions; span length, mass, and stiffness imperfection; viscous damping; axial force; transverse support and rotational coupling stiffness; and modeling resolution. Three configurations are studied, commencing with two different two-span models, and culminating in a ten-span configuration resembling lattice-type large space structures. Results indicate that, in addition to the ratio of imperfection to coupling stiffness being an important localization parameter, transverse support stiffness and Timoshenko beam effects greatly affect the tendency of a structure to exhibit localized modes.

Lust, S. D.↗
NASA NTRS1990

Nonlinear coupled rotor-fuselage helicopter vibration studies with higher harmonic control

This paper addresses the problem of vibration prediction and vibration reduction in helicopters by means of active control methodologies. The nonlinear equations of a coupled rotor/flexible-fuselage system have been derived using computer algebra, thus relegating this tedious task to the computer. In the solution procedure the trim state and vibratory response of the helicopter are obtained in a single pass by using a harmonic balance technique and simultaneously satisfying the trim and the vibratory response of the helicopter in all the rotor and fuselage degrees of freedom. Using this solution procedure, the influence of the fuselage flexibility on the vibratory response is studied. In addition, it is shown that the conventional single frequency HHC is capable of reducing either the hub loads or only the fuselage vibrations but not both simultaneously. A new scheme called MHHC, having multiple higher harmonic pitch inputs, was used to accomplish this task of simultaneously reducing both the vibratory hub loads and fuselage vibratory response. In addition, the uniqueness of this MHHC scheme is explained in detail.

Friedmann, P. P.↗
NASA NTRS1989

Time domain unsteady incompressible cascade airfoil theory for helicopter rotors in hover

A detailed derivation of a finite-time arbitrary-motion incompressible cascade theory is presented for both Laplace and frequency domains. The generalized cascade lift deficiency function is shown to be consistent with the generalized Theodorsen's lift deficiency function when the wake spacing approaches infinity or when the reduced frequency tends to infinity; it also yields a correct value for the zero reduced frequency limit. Efficient numerical procedures are presented for the evaluation of the cascade lift deficiency function. Numerical examples comparing the cascade lift deficiency function with Loewy's (1957) rotary-wing lift deficiency function in frequency domain are presented. Pade approximants of the cascade lift deficiency function are constructed using a Bode plot approach that allows for complex poles. A general-purpose optimization program is used to determine the coefficients of the approximant.

Dinyavari, M. A. H.↗
NASA NTRS1989

Analytic simulation of higher harmonic control using a new aeroelastic model

This paper describes a higher harmonic control (HHC) study of a four bladed hingeless rotor using a coupled flap-lag-torsional aeroelastic stability and response analysis which incorporates finite-state, time-domain aerodynamics. The rotor trim condition is determined using a coupled trim-aeroelastic analysis. Deterministic and cautious controllers based on local and global HHC models are implemented with different combinations of input parameters identified using a Kalman filter. The effects of unsteady versus quasisteady aerodynamic modeling on HHC simulations are investigated, including the effectiveness of the local and global HHC models and the advantages of different identification schemes.

Friedmann, P. P.↗