Engineering topics

Fries, Joseph

Publications and source records attributed to Fries, Joseph.

18 records

NASA NTRS2000

The Presence of Excess Oxygen in Burning Metallic Materials

Early work on burning of iron rods under conditions of the ATSM/NASA flammability test showed that there was excess oxygen, that is, above stoichiometric requirements for iron(III) oxide, present in the molten product during burning. Since that work, this phenomenon has been confirmed for burning under microgravity conditions and has been observed for a wide range of metals under burning conditions of a single micro-drop at ambient pressures and 20-second microgravity tests under pressurized oxygen-enriched conditions. This paper reviews these experimental observations and discusses the possible thermodynamic analysis for the metals iron, aluminum, and cobalt. The excess oxygen in the burning molten iron oxide was represented as combined to form a series of ferrite ions. For aluminum the excess oxygen is represented as a bridging species and a similar explanation is postulated for the cobalt system.

Wilson, D. Bruce↗

NASA NTRS2000

Ignition Resistance of Polymeric Materials to Particle Impact in High-Pressure Oxygen

Particle impact ignition has been the primary cause of numerous fires in oxygen systems. This ignition phenomenon is known to occur where particles are present in high-velocity gas, and where impact occurs on a flammable material. The particle impact ignition behavior of many metals has been widely studied, but the particle impact ignition behavior of polymeric materials is relatively unknown. Particle impact ignition in polymeric materials is a concern as these materials are commonly used in component seat and seal applications, where high-velocity particle impacts can occur. This study evaluates several polymeric materials and compares the minimum temperature required for ignition (threshold temperature) of these materials: Kel-F 81 (CTFE), Teflon (PTFE), PEEK, Vespel SP-21, and Nylon 6/6. The materials were configured as targets in the White Sands Test Facility high-velocity particle impact test system. Gaseous oxygen was flowed at 4000 psi and sonic velocity, and the targets were impacted with 2000-micron aluminum 2017 particles. This paper discusses the results of these tests and ranks the materials according to their threshold temperatures at these conditions.

Forsyth, Elliot T.↗

NASA NTRS2000

Test System to Study the Ignition of Metals by Polymers in Oxygen

A new test system that uses Laser energy to ignite a polymer promoter has been developed at the NASA White Sands Test Facility. It will facilitate the study of the spread of fire from a burning polymer material to the metal surrounding it. The system can be used to answer questions regarding the effects of configuration on ignition and combustion. The data obtained from this test could also be used to develop mathematical models for analyzing the effects of configuration on ignition and combustion. The system features a 10,000-psi (69-MPa) test chamber with sight glass windows on either end and a 25-watt carbon dioxide Laser for an ignition source. The test system can be used with gaseous oxygen, nitrogen or any mixture of the two gases. To minimize the effect of preheating the metallic, the polymer is ignited with a minimal amount of Laser energy. Igniting the polymer in this fashion also simplifies the thermodynamic analysis of the ignition and propagation reactions. The system is very robust, versatile and straightforward to use. Depending on the test pressure and configuration, the test system operator can perform as many as 20 tests per day. Test results verify that ignition and combustion of the metallic sample is not only dependent on pressure, material type and temperature, but configuration of both the polymer promoter and metallic sample. Both 6061 aluminum and 316 stainless steel 0.25-inch (6.35-mm) diameter rods with a standard 0-ring groove were tested with Buna-N, Silicone, Teflon and Viton 0-rings. The system ignited all four types of 0-rings in oxygen at pressures ranging from ambient to 10,000 psi (69 MPa). However, neither the stainless steel nor the aluminum rods on which the O-rings were mounted ignited in any test conditions. Future testing may be done on the 0.25-inch (6.35-mm) rod and O-ring configuration to evaluate the lack of ignition in these tests. Future configurations may include a plug of polymer in the base of the sample and replicas of fire-damaged components. Furthermore, the test system may be used in the future to analyze the oxidation rate of Laser-heated metals in gaseous oxygen.

Shoffstall, Michael S.↗

NASA NTRS2000

Flammability: A Review and Analysis

With its founding in 1975, Committee G-4 of the American Society for Testing and Materials (ASTM) embarked on the process of defining the flammability of metallic materials in oxygen-enriched atmospheres. In this process, they are joined by the National Aeronautics and Space Administration (NASA), the National Fire Protection Association (NFPA), and the Compressed Gas Association (CGA). Although none of these organizations has explicitly defined flammability, the following definitions and statements provide a composite understanding of the concept: 1. "This Standard Guide (ASTM G94-92) is concerned primarily with the properties of a material associated with its relative susceptibility to ignition and propagation of combustion." 2. "A material is considered flammable at the maximum use pressure if at least one sample burns more than 6 in. (15.2 cm). At least, five samples must be tested." NASA 3. "Flammable: Capable, when ignited of maintaining combustion under the specified environmental conditions." NFPA 53. 4. "Combustion: A complex sequence of chemical reactions between a fuel and an oxidant accompanied by the evolution of heat, and usually, the emission of light." NFPA 53. and 5. "A safe oxygen-piping transmission or distribution system is one that is designed and installed in accordance with all applicable codes and regulations for the service conditions and locations involved and further meets the special requirements for oxygen services." CGA-G4 Flammability thus equates, after ignition, to propagation of combustion, synonymous with steady state burning, under specified environmental conditions. Properties for which quantitative values are given in ASTM G94-92 and which are used to describe metals flammability consistent with the concept of steady state burning are either system independent properties, such as, enthalpies of reaction, burn ratios, flame temperatures, thermal conductivity, and heat release; or system dependent properties, such as, oxygen index, promoted combustion, threshold pressure and burn rates. Each property is reviewed and analyzed as to whether it provides an absolute or relative measure for flammability. It is shown that burn ratio, as applied to the actual steady state combustion condition, approaches the desired absolute measure of flammability.

Wilson, D. Bruce↗

NASA NTRS2000

Model of ASTM Flammability Test in Microgravity: Iron Rods

There is extensive qualitative results from burning metallic materials in a NASA/ASTM flammability test system in normal gravity. However, this data was shown to be inconclusive for applications involving oxygen-enriched atmospheres under microgravity conditions by conducting tests using the 2.2-second Lewis Research Center (LeRC) Drop Tower. Data from neither type of test has been reduced to fundamental kinetic and dynamic systems parameters. This paper reports the initial model analysis for burning iron rods under microgravity conditions using data obtained at the LERC tower and modeling the burning system after ignition. Under the conditions of the test the burning mass regresses up the rod to be detached upon deceleration at the end of the drop. The model describes the burning system as a semi-batch, well-mixed reactor with product accumulation only. This model is consistent with the 2.0-second duration of the test. Transient temperature and pressure measurements are made on the chamber volume. The rod solid-liquid interface melting rate is obtained from film records. The model consists of a set of 17 non-linear, first-order differential equations which are solved using MATLAB. This analysis confirms that a first-order rate, in oxygen concentration, is consistent for the iron-oxygen kinetic reaction. An apparent activation energy of 246.8 kJ/mol is consistent for this model.

Steinberg, Theodore A↗

NASA NTRS2000

Indicator Devices for Detection of Trace Gaseous Hydrazines

The relatively recent decrease in the acceptable time-weighted-average for hydrazines from 100 parts-per-billion (ppb) to 10 ppb rendered many trace hydrazine detectors either insensitive or inaccurate. Development of a rapid detection method for hydrazines at the new 10-ppb concentration was necessary so that test area personnel could reliably assess airborne hydrazines concentrations of a potentially contaminated area prior to entry. The reduction of Au(III) to Au(0) by hydrazines is a well characterized reaction and application of the corresponding yellow to purple color change was selected as a potentially useful means for detection of trace hydrazines in air. Tests with small quantities of KAuCl4 deposited on a variety of substrates were conducted using verified sources of 1,1-dimethylhydrazine, methylhydrazine, and hydrazine at approximately 10 ppb in air. Substrates tested were glass fiber filter paper, glass beads, anion exchange resin (AuCl4- form), and diatomaceous earth. The most successful of these substrates were glass fiber filter paper and diatomaceous earth. The KAuC14 impregnated glass fiber filter paper appeared to be somewhat light sensitive so further tests were conducted using the diatomaceous earth substrate. KAuCl4 concentration, substrate particle size, and sampler configuration were evaluated. Based on these tests, the device selected for further evaluation was a 5mm OD by 50mm glass tube containing 0.02-0.03g of 45/60 mesh diatomaceous earth coated with 2 percent KAuCl4. When connected to a sampling pump, response of the device to changes in relative humidity, ambient light, and high levels of other fluids, which might also be found in a propellant test area, was evaluated. False positive responses were not detected for exposures to relative humidity changes from 10 to 80 percent, sunlight for greater than 10 minutes, or percent levels of ammonia, isopropyl alcohol, nitrogen dioxide, and hydrogen. In addition, body emissions did not produce a false positive response in view of potential application for use inside protective clothing. The device was shown to reliably detect less than 10 ppb of the hydrazines tested using a 10 to 20L sample followed by a 2 to 5 minute color development time. Some field tests were conducted in parallel with conventional acidic firebrick sorbent tubes. There was generally very good agreement between the devices and firebrick sorbent tubes when greater than 10 ppb of a hydrazine was present.

Dee, Lou A.↗

NASA NTRS2000

Impurities Formed in Artificially Aged Methylhydrazine

A sample of monomethylhydrazine (MMH) meeting MIL-PRF-27404C requirements was split into two portions. One portion was periodically exposed to atmospheric contaminants while stored in clear glass, and the other portion, held as a reference sample, was stored under nitrogen in amber glass. Impurities in both samples were periodically characterized by Gas Chromatograph-Mass Spectrometer (GC-MS) to determine what changes might occur in MMH when it is stored in less than ideal conditions. The qualitative and semi-quantitative results of this study are reported herein.

McClure, Mark B.↗

NASA NTRS2000

Hypergolic Propellant Safety Course

Under the sponsorship of the NASA Safety Training Center at the Johnson Space Center, a hypergolic propellant safety course has been developed. This is a 2-day course on guidelines for hypergolic propellant system design, materials selection, operations, storage, and transportation. Recognizing that numerous fuels and oxidizers can be hypergolic, this course is specific to the hydrazine family of fuels and nitrogen tetroxide and its variants. The objectives of the course are to enable the student to identify and evaluate the hazards of hypergolic propellants, and to understand the methods for controlling those hazards and responding to emergencies. The course covers properties and hazards of the hydrazines and oxidizers; design and operations in hypergolic facilities; materials selection for use in hypergol systems; storage vessels, piping, and component considerations; hypergol detection; fire fighting practices; operating and transportation principles and procedures; and emergency practices and considerations. A hazards analysis methodology is presented. Numerous references are provided and the applicability of certain regulatory documents is discussed. A brief overview of other propellants, including hydrogen peroxide, is given at the end of the course.

Rathgeber, Kurt A.↗

NASA NTRS2000

Comparison of The Dimensional Stability of Kel-F 81 and Neoflon CTFE M400H Polychlorotrifluoroethylenes Used in Valve Seat Application

The dimensional stability of polychlorotrifluoroethylene (PCTFE) valve seats used in oxygen regulator applications was determined by thermomechanical analysis (TMA). Two traceable grades of PCTFE were tested; Kel-F 81 and Neoflon CTFE M400H. For these particular resins, the effect of percent crystallinity, zero strength time (ZST) molecular weight, resin grade, process history (compression-molded versus extruded) on the dimensional stability and annealing behavior was determined. In addition to the traceable Kel-F 81 and Neoflon CTFE M400H grades, actual PCI'PH valve seats of differing geometry and design were tested by TMA. The PCTFE valve seats were of unspecified resin grade, although certain inferences about the grade could be drawn based on knowledge of the valve seat fabrication date. Results consistently revealed dimensional instability of varying magnitude at temperatures ranging from 40 to 70 degrees Celsius. Furthermore, some of the pre- 1 995 seats appeared to be more dimensionally stable than those fabricated after 1995. The TMA results are discussed in the context of several proposed ignition mechanisms; namely, particle impact, presence of contaminant oils and fibers, and localized heating by flow friction and/or resonance. The effect of metal constraint on the dimensional stability of PCTFE is also discussed. Finally, the effect of percent crystallinity, ZST molecular weight, resin grade, process history (compression-molded versus extruded) on the AIT, delta Hc and impact sensitivity of various types of Neoflon CTFE M400H was determined using Kel-F 81 as a control. Results show that the AIT, delta Hc and impact sensitivity were essentially independent of Neoflon CTFE process history and structure.

Waller, Jess M.↗

NASA NTRS2000

A Model For The Burning of Teflon

Teflon has been identified as suitable material for use in oxygen-enriched atmospheres because of its low specific enthalpy of combustion that is, less than 1500 cal/gram. However, once ignited, Teflon burns in a heterogeneous reaction until total consumption or depletion of oxygen occurs. A model is developed for the burning of Teflon in pure, high-pressure oxygen, 3.4 to 68.9 MPa. The Teflon polymer chain dissociates via monomer units due to pyrolysis. These monomer units diffuse to the surface due to free convection. The model consists of coupled mass and energy balances for the polymer and an energy balance for the free convection of product gases. The model is used to obtain appropriate kinetic parameters for the dissociation and surface reactions. The model is validated against experimental measurements of Teflon discs supported on aluminum rods (2216) at oxygen pressures of 3.4, 6.8, 34.4, and 68.9 MPa. The model simulates the temperature distribution in the product gases above burning Teflon.

Waller, Jess M.↗

NASA NTRS2000

Polymer-Oxygen Compatibility Testing: Effect of Oxygen Aging on Ignition and Combustion Properties

The oxygen compatibility of six polymers used in oxygen service was evaluated after exposure for 48 hours to oxygen pressures ranging from 350 to 6200 kPa (50 to 900 psia), and temperatures ranging from 50 to 250 C (122 to 302 F). Three elastomers were tested: CR rubber (C873-70), FKM fluorocarbon rubber (Viton A), and MPQ silicone rubber (MIL-ZZ-765, Class 2); and three thermoplastics were tested: polyhexamethylene adipamide (Zytel 42), polytetrafluoroethylene (Teflon TFE), and polychlorotrifluoroethylene (Neoflon CTFE M400H). Post-aging changes in mass, dimensions, tensile strength, elongation at break, and durometer hardness were determined. Also, the compression set was determined for the three elastomers. Results show that the properties under investigation were more sensitive to oxygen pressure at low to moderate temperatures, and more sensitive to temperature at low to moderate oxygen pressures. Inspection of the results also suggested that both chain scissioning and cross-linking processes were operative, consistent with heterogeneous oxidation. Attempts are underway to verify conclusively the occurrence of heterogeneous oxidation using a simple modulus profiling technique. Finally, the effect of aging at 620 kpa (90 psia) and 121 C (250 F) on ignition and combustion resistance was determined. As expected, aged polymers were less ignitable and combustible (had higher AlTs and lower heats of combustion). Special attention was given to Neoflon CTFE. More specifically, the effect of process history (compression versus extrusion molding) and percent crystallinity (quick- versus slow-quenched) on the AIT, heat of combustion, and impact sensitivity of Neoflon CTFE was investigated. Results show the AIT, heat of combustion, and impact sensitivity to be essentially independent of Neoflon CTFE process history and structure.

Waller, Jess M.↗

NASA NTRS1999

Space Shuttle Orbital Maneuvering Subsystem (OMS) Engine Propellant Leakage Ball-Valve Shaft Seals

Evidence of propellant leakage across ball-valve shaft seals has been noted during the disassembly of five flight engines and one test engine at the NASA Lyndon B. Johnson Space Center, White Sands Test Facility. Based on data collected during the disassembly of these five engines, the consequences of propellant leakage across the ball-valve shaft seals can be divided into four primary areas of concern: Damage to the ball-valve pinion shafts, damage to sleeved bearings inside the ball-valve and actuator assemblies, degradation of the synthetic rubber o-rings used in the actuator assemblies, and corrosion and degradation to the interior of the actuator assemblies. The exact time at which leakage across the ball-valve shaft seals occurs has not been determined, however, the leakage most likely occurs during engine firings when, depending on the specification used, ball-valve cavity pressures range as high as 453 to 550 psia. This potential pressure range for the ball-valve cavities greatly exceeds the acceptance leakage test pressure of 332 psia. Since redesign and replacement of the ball-valve shaft seals is unlikely, the near term solution to prevent damage that occurs from shaft-seal leakage is to implement a routine overhaul and maintenance program for engines in the fleet. Recommended repair, verification, and possible preventative maintenance measures are discussed in the paper.

Lueders, Kathy↗

NASA NTRS1999

Sensitive Procedures for Determining the Permeation Resistance of Chlorinated Polyethylene Against Liquid Propellants

The permeation resistance of chlorinated polyethylene (CPE) used in totally encapsulating chemical protective suits against the aerospace fuels hydrazine, monomethylhydrazine, and uns-dimethylhydrazine was determined by measuring the breakthrough time (BT) and time-averaged vapor transmission rate (VTR) using procedures consistent with ASTM F 739 and ASTM F 1383. Two exposure scenarios were simulated: a 2 hour (h) fuel vapor exposure, and a liquid fuel "splash" followed by a 2 h vapor exposure. To simulate internal suit pressure during operation, a positive differential pressure of 0.3 in. water (75 Pa) on the collection side of the permeation apparatus was used. Using the available data, a model was developed to estimate propellant concentrations inside an air-line fed, totally encapsulating chemical protective suit. Concentrations were calculated under simulated conditions of fixed vapor transmission rate, variable breathing air flow rate, and variable splash exposure area. Calculations showed that the maximum allowable permeation rates of hydrazine fuels through CPE were of the order of 0.05 to 0.08 ng/sq cm min for encapsulating suits with low breathing air flow rates (of the order of 5 scfm or 140 L min-1). Above these permeation rates, the 10 parts-per-billion (ppb) threshold limit value time-weighted average could be exceeded. To evaluate suit performance at 10 ppb threshold-limiting value/time-weighted average level concentrations, use of a sensitive analytical method such as cation exchange high performance liquid chromatography with amperometric detection was found to be essential. The analytical detection limit determines the lowest measurable VTR, which in turn governed the lowest per meant concentration that could be calculated inside the totally encapsulating chemical protective suit.

Waller, Jess M.↗

NASA NTRS1999

Mars Observer Propulsion and Pyrotechnics Corrective Actions Test Program Blanket Release

The Mars Observer Propulsion and Pyrotechnic Corrective Actions Test Program has been in progress at the NASA White Sands Test Facility since 1995. This program has developed capabilities to accurately characterize pyrovalve hazards and has established corrective actions that arc helping to preclude loss of spacecraft due to pyrovalve and propellant interaction. Rather than wait for conclusion of the test program, significant rest results, findings, and safety recommendations have been and will continue to be released soon after they became available to meet needs of near-term NASA and commercial space programs. This release will cover approximately three to five papers per year until program end.

Saulsberry, Regor L.↗

NASA NTRS1999

Recent Developments in Chemically Reactive Sensors for Propellants

Propellant system leaks can pose a significant hazard in aerospace operations. For example, a leak in the hydrazine supply system of the shuttle auxiliary power unit (APU) has resulted in hydrazine ignition and fire in the aft compartment of the shuttle. Sensors indicating the location of a leak could provide valuable information required for operational decisions. WSTF has developed a small, single-use sensor for detection of propellant leaks. The sensor is composed of a thermistor bead coated with a substance which is chemically reactive with the propellant. The reactive thermistor is one of a pair of closely located thermistors, the other being a reference. On exposure to the propellant, the reactive coating responds exothermically to it and increases the temperature of the coated-thermistor by several degrees. The temperature rise is sensed by a resistive bridge circuit, and an alarm is registered by data acquisition software. The concept is general and has been applied to sensors for hydrazine, monomethylhydrazine, unsym-dimethylhydrazine, ammonia, hydrogen peroxide, ethanol, and dinitrogen tetroxide. Responses of these sensors to humidity, propellant concentration, distance from the liquid leak, and ambient pressure levels arc presented. A multi-use sensor has also been developed for hydrazine based on its catalytic reactivity with noble metals.

Davis, Dennis D.↗

NASA NTRS1999

A Multiphase Equation of State for Hydrazine and Monomethylhydrazine

The objective of this work was to obtain a validated equation of state for hydrazine and monomethylhydrazine (MMH) and use this equation to calculate thermodynamic properties. The approach was based on using both reliable critical property values and a value of the acentric factor in the Soave Redlich Kwong and the Peng Robinson model equations of state. These equations were validated by comparing calculated molar volumes for phase equilibrium with published experimental values and comparing calculated vapor pressures with published experimental values over the temperature range appropriate for the corresponding state equations. The equation of state giving the best results was used to calculate enthalpy and entropy departure functions and fugacity values. Additional thermodynamic property calculations were performed to produce partial Mollier diagrams and thermodynamic properties containing internal energy, enthalpy, and entropy values for hydrazine and MMH. The analyses of systems in which either adiabatic or near-adiabatic compression of liquid or vapor hydrazine or low velocity detonations occur require a validated equation of state for representing occurring molar volumes and for energy calculations. Other calculations for thermodynamic properties of hydrazine are available, but the values are for a strict ideal gas state. This work characterized destructive events using hydrazine by calculating for isentropic compression temperatures. The final temperatures were calculated and compared using the ideal and real gas fluid equations of state.

Barragan, Michelle↗

NASA NTRS1999

Status of WSTF Pyrovalve Handbook Development in Year 2000

Significant data have been generated through various spacecraft propulsion system projects involving the use of pyrotechnically operated valves (pyrovalves). These data need to be analyzed, interpreted, summarized, associated, and formatted so they can be made available for spacecraft propulsion system design involving pyrovalves and used to specify test procedures in the performance evaluation and qualification of these systems. To meet this need, a Pyrovalve Handbook is being developed at the NASA White Sands Test Facility. Standards of performance for pyrovalve applications are being formulated under the sponsorship of the NASA Technical Standards Program, as are pyrovalve testing standards under the sponsorship of the NASA Safety and Risk Management Program. The ultimate goal is to have the Handbook adopted as a voluntary standard under the guidance of the AIAA Energetic Components and Systems Technical Committee and, in a more restrictive format, become an integral part of ISO standards for Explosive Systems and Devices Used on Space Vehicles. Feedback from both Government and industry is encouraged and will be the focus of the presentation. It is especially critical that feedback be received on content and formatting of the Handbook to maximize benefit to the technical community. Submission of validated data from organizations outside of NASA is also encouraged.

Howard, Julien L.↗

NASA NTRS1999

Mars Observer Propulsion and Pyrotechnics Corrective Actions Test Program Status-1999

An extensive propulsion and pyrotechnic test program has been in progress at the NASA White Sands Test Facility since 1995. This program created the capabilities to: accurately measure and characterize pyrovalve combustion product blow-by into propellant systems; characterize valve operation using a Velocity Interferometer System for Any Reflector (VISAR); and evaluate hydrazine and monomethylhydrazine thermal decomposition initiated by blow-by. These capabilities were further utilized and refined this year. Low blow-by pyrovalves manufactured by Conax Florida Corporation continued to be evaluated as a potential corrective measure for blow-by induced propellant explosions. Development and testing of various advanced pyrovalves and investigation of explosion mechanisms also continued. Current and near-term testing includes: evaluation of 3/8 in. Conax pyrovalves and other commercially available valves; development and testing of advanced pyrovalve subcomponent technologies including a zero blow-by pyrovalve ram, composite overwrapped ram cylinder, and a zero particulate generating poppet; investigation of non-destructive evaluation techniques to evaluate pyrovalve ram seals; and testing and modeling of pyrotechnically induced explosive hydrazine decomposition. Evaluation of 3/8 in. Conax valves will include operational margin testing to be accomplished at NASA Langley Research Center. The test program also seeks to compile and format significant amounts of data from this and other pyrovalve test programs to generate a pyrovalve applications handbook. The handbook will facilitate formation of standards that ensure safe spacecraft applications. Current data and future plans are discussed, and community interaction is encouraged.

Saulsberry, Regor↗