Investigations in Reduced-Order Aerodynamic Modeling of Aircraft Approaching Stall
No abstract available
Frink, N. T.↗
Engineering topics
Frink, N. T.
Publications and source records attributed to Frink, N. T..
Transonic Drag Prediction on a DLR-F6 Transport Configuration Using Unstructured Grid Solvers
A second international AIAA Drag Prediction Workshop (DPW-II) was organized and held in Orlando Florida on June 21-22, 2003. The primary purpose was to inves- tigate the code-to-code uncertainty. address the sensitivity of the drag prediction to grid size and quantify the uncertainty in predicting nacelle/pylon drag increments at a transonic cruise condition. This paper presents an in-depth analysis of the DPW-II computational results from three state-of-the-art unstructured grid Navier-Stokes flow solvers exercised on similar families of tetrahedral grids. The flow solvers are USM3D - a tetrahedral cell-centered upwind solver. FUN3D - a tetrahedral node-centered upwind solver, and NSU3D - a general element node-centered central-differenced solver. For the wingbody, the total drag predicted for a constant-lift transonic cruise condition showed a decrease in code-to-code variation with grid refinement as expected. For the same flight condition, the wing/body/nacelle/pylon total drag and the nacelle/pylon drag increment predicted showed an increase in code-to-code variation with grid refinement. Although the range in total drag for the wingbody fine grids was only 5 counts, a code-to-code comparison of surface pressures and surface restricted streamlines indicated that the three solvers were not all converging to the same flow solutions- different shock locations and separation patterns were evident. Similarly, the wing/body/nacelle/pylon solutions did not appear to be converging to the same flow solutions. Overall, grid refinement did not consistently improve the correlation with experimental data for either the wingbody or the wing/body/nacelle pylon configuration. Although the absolute values of total drag predicted by two of the solvers for the medium and fine grids did not compare well with the experiment, the incremental drag predictions were within plus or minus 3 counts of the experimental data. The correlation with experimental incremental drag was not significantly changed by specifying transition. Although the sources of code-to-code variation in force and moment predictions for the three unstructured grid codes have not yet been identified, the current study reinforces the necessity of applying multiple codes to the same application to assess uncertainty.
Lee-Rausch, E. M.↗
Tetrahedral Finite-Volume Solutions to the Navier-Stokes Equations on Complex Configurations
A review of the algorithmic features and capabilities of the unstructured-grid flow solver USM3Dns is presented. This code, along with the tetrahedral grid generator, VGRIDns, is being extensively used throughout the U.S. for solving the Euler and Navier-Stokes equations on complex aerodynamic problems. Spatial discretization is accomplished by a tetrahedral cell-centered finite-volume formulation using Roe's upwind flux difference splitting. The fluxes are limited by either a Superbee or MinMod limiter. Solution reconstruction within the tetrahedral cells is accomplished with a simple, but novel, multidimensional analytical formula. Time is advanced by an implicit backward-Euler time-stepping scheme. Flow turbulence effects are modeled by the Spalart-Allmaras one-equation model, which is coupled with a wall function to reduce the number of cells in the near-wall region of the boundary layer. The issues of accuracy and robustness of USM3Dns Navier-Stokes capabilities are addressed for a flat-plate boundary layer, and a full F-16 aircraft with external stores at transonic speed.
Frink, N. T.↗
Review of vortex flow flight projects on the F-106B
NASA-Langley's F-106B research aircraft is being used in vortex flow-research flight experiments in order to determine the effects of Re number and Mach number on the lee-side vortex system generated at angles-of-attack up to maneuver condition, as well as to evaluate the aerodynamic characteristics of a sharp leading-edge vortex flap system. The wing vortex system is visualized at a fixed position by means of the vapor-screen technique. Comparisons are made between a measured value and two theoretical estimates of a pertinent vortex system property, core location.
Lamar, J. E.↗
Deployable Truss Member
Compact telescoping roll extends 24 times its length. Roll telescopes into extended truss member when force is applied. Truss members deployed by various means. Truss member initially constructed in its stowed state with appropriate sheet material rolled around central core. For deployment truss extends by centrifugal force to form cone. With both ends fastened to prevent unrolling, rigid truss member formed.
Frink, N. T.↗
Vortex flap flow reattachment line and subsonic longitudinal aerodynamic data on 50 deg to 74 deg Delta wings on common fuselage
Positions of the primary vortex flow reattachment line and longitudinal aerodynamic data were obtained at Mach number 0.3 for a systematic series of vortex flaps on delta wing body configurations with leading edge sweeps of 50, 58, 66, and 74 deg. The investigation was performed to study the parametric effects of wing sweep, vortex flap geometry and deflection, canards, and trailing edge flaps on the location of the primary vortex reattachment line relative to the flap hinge line. The vortex reattachment line was located via surface oil flow photographs taken at selected angles of attack. Force and moment measurements were taken over an angle of attack range of -1 deg to 22 deg at zero sideslip angle for many configurations to further establish the data base and to assess the aforementioned parametric effects on longitudinal aerodynamics. Both the flow reattachment and aerodynamic data are presented.
Frink, N. T.↗
Recent advances in applying Free Vortex Sheet theory to the estimation of vortex flow aerodynamics
Free Vortex Sheet theory has been applied to a variety of configurations for the estimation of three-dimensional pressure distributions for wings developing separation-induced leading-edge vortex flows. Correlations with experiment show reasonable estimates for the effects of compressibility, side-slip, side edges, swept-wing blast-induced loads, and leading-edge vortex flaps. Theoretical studies expand upon these correlations to show general aerodynamic trends. Consideration is also given to simple, yet effective techniques which expedite convergence and therefore reduce computational expense.
Luckring, J. M.↗
Analytical study of vortex flaps on highly swept delta wings
This paper highlights some current results from ongoing analytical studies of vortex flaps on highly swept delta wings. A brief discussion of the vortex flow analysis tools is given along with comparisons of the theories to vortex flap force and pressure data. Theoretical trends in surface pressure distribution for both angle-of-attack variation and flap deflection are correctly predicted by Free Vortex Sheet theory. Also shown are some interesting calculations for attached-flow and vortex-flow flap hinge moments that indicate flaps utilizing vortex flow may generate less hinge moment than attached flow flaps. Finally, trailing-edge flap effects on leading-edge flap thrust potential are investigated and theory-experiment comparisons made.
Frink, N. T.↗
Experimental and analytical study of the longitudinal aerodynamic characteristics of analytically and empirically designed Strake-wing configurations at subcritical speeds
Sixteen analytically and empirically designed strakes have been tested experimentally on a wing-body at three subcritical speeds in such a way as to isolate the strake-forebody loads from the wing-afterbody loads. Analytical estimates for these longitudinal results are made using the suction analogy and the augmented vortex lift concepts. The synergistic data are reasonably well estimated or bracketed by the high- and low-angle-of-attack vortex lift theories over the Mach number range and up to maximum lift or strake-vortex breakdown over the wing. Also, the strake geometry is very important in the maximum lift value generated and the lift efficiency of a given additional area. Increasing size and slenderness ratios are important is generating lift efficiently, but similar efficiency can also be achieved by designing a strake with approximately half the area of the largest gothic strake tested. These results correlate well with strake-vortex-breakdown observations in the water tunnel.
Lamar, J. E.↗
Aerodynamic features of designed strake-wing configurations
Sixteen analytically and empirically designed strakes have been aerodynamically tested on a common wing-body to determine the longitudinal characteristics of the configurations. These strakes were selected, in general, due to their superior performance in a water-tunnel test. There they exhibited a good correlation between the hypothesized high value of angle of attack for strake vortex breakdown and the high value of leading-edge suction at the strake tip. The lift and pitch data were reasonably well predicted by an extended suction analogy method, and the lift agreement improved with increasing strake area. The strake-vortex-breakdown angle and configuration maximum lift generally increase with increasing strake area and, to some extent, strake tip leading-edge suction value. The best strake configurations all developed about the same maximum area efficiency value despite their differences in size.
Lamar, J. E.↗
Water-tunnel and analytical investigation of the effect of strake design variables on strake vortex breakdown characteristics
A systematic water-tunnel study was made to determine the vortex breakdown characteristics of 43 strakes. The strakes were mounted on a 1/2-scale model of a Langley Research Center general research fighter fuselage model with a 44deg leading-edge-sweep trapezoidal wing. The analytically designed strake shapes provided examples of the effects of the primary design parameters (size, span, and slenderness) on vortex breakdown characteristics. These effects were analyzed in relation to the respective strake leading-edge suction distributions. Included were examples of the effects of detailed strake planform shaping. It was concluded that, consistent with the design criterion, those strakes with leading-edge suction distributions which increase more rapidly near, and have a higher value at, the spanwise tip of the strake produce a more stable vortex.
Frink, N. T.↗
An analysis of strake vortex breakdown characteristics in relation to design features
This paper describes a water tunnel study of the vortex breakdown characteristics of a large number of analytically designed vortex strakes tested in combination with a moderate aspect ratio trapezoidal wing. A wide range of strake sizes and slenderness ratios are covered, and examples of the effects of the primary design parameters of size, span, and slenderness on the vortex breakdown characteristics are presented and analyzed in relation to the leading-edge suction distributions. Several examples of detailed planform shaping on strakes of the same general size and slenderness are shown from which it can be concluded that, consistent with the design criterion, those with leading-edge suction distributions which increase more rapidly near, and have a higher value at, the spanwise tip of the strake produce a more stable vortex.
Frink, N. T.↗
Investigation of aerodynamic characteristics of subsonic wings
An analytical strake design procedure is investigated. A numerical solution to the governing strake design equation is used to generate a series of strakes which are tested in a water tunnel to study their vortex breakdown characteristics. The strakes are scaled for use on a half-scale model of the NASA-LaRC general research fuselage with a 44 degrees trapezoidal wing. An analytical solution to the governing design equation is obtained. The strake design procedure relates the potential-flow leading-edge suction and pressure distributions to vortex stability. Several suction distributions are studied and those which are more triangular and peak near the tip generate strakes that reach higher angles of attack before vortex breakdown occurs at the wing trailing edge. For the same suction distribution, a conical rather than three dimensional pressure specification results in a better strake shape as judged from its vortex breakdown characteristics.
Dejarnette, F. R.↗