Search NASA⌕ Search

Engineering topics

Gabriel F. Benavides

Publications and source records attributed to Gabriel F. Benavides.

5 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

High-Propellant Throughput Sub-kW Electric Propulsion System for Deep Space Science and Exploration

The National Aeronautics and Space Administration (NASA) is maturing high-propellant throughput sub-kilowatt electric propulsion technologies to enable small spacecraft deep space science and exploration missions with high delta-v requirements. The pathfinder model (PM) propulsion system consists of the H71M-PM Hall-effect thruster, a breadboard 1-kW power processing unit (PPU), and a propellant flow control system. The propulsion system requirements balance the needs of various high delta-v NASA and commercial industry mission concepts to achieve a design that both enables a variety of NASA small spacecraft deep space missions, while remaining viable for select commercial applications. The H71M-PM thruster has completed performance characterization and three 500-h short duration wear tests (SDWT). The propulsion system provides stable thrust generation over a wide range of operating conditions from 200 W to 1 kW, and 200 V to 400 V. The thruster has demonstrated a thrust as high as 68 mN at 300 V and 1 kW. The thruster has similarly demonstrated a specific impulse of 1850 s at 400 V and 1 kW. Key surfaces were machined between each SDWT to simulate accelerated discharge channel and pole cover erosion. Profilometry scans across masked pole cover surfaces were conducted to determine erosion rates. SDWT results support that a target thruster lifetime of 14 kh with 50% margin is achievable. Component testing has demonstrated propellant azimuthal flow uniformity better than ± 2 percent of the nominal value, azimuthal magnetic field uniformity better than ± 0.5 percent of the nominal value, and cathode heater cycle testing to greater than 30,000 cycles. Propulsion system integrated system testing is planned to use the H71M-PM and a breadboard 1-kW PPU. Pathfinder model test results are now supporting the design of the H71M-EM engineering model thruster. A second-generation breadboard PPU has been fabricated and is currently under test. NASA has made these technologies available to U.S. industry through a no cost, nonexclusive license agreement.

Hall↗
NASA NTRSDate not supplied

Electric Propulsion Qualification Guidelines and Best Practices for NASA Small Spacecraft Missions

Electric propulsion being developed for CubeSats and other small satellites with the taught expectation that high risk is generally acceptable are resulting in devices that do not meet a minimum expectation of engineering rigor for many missions, including appropriate qualification testing. This paper proffers a preliminary set of recommended guidelines and best practices in dialogue with the smallsat community to strike a better balance between engineering rigor and cost effectiveness for the qualification of EP technologies under consideration for NASA small spacecraft.

Thomas M. Liu↗
NASA NTRSDate not supplied

Testing the Effectiveness of Integrated Plume Shield for a Hall Thruster

Hall thrusters have been shown to exhibit side plumes with varying degree of erosive power. This article presents the concept of the integrated plume shield for the purpose of mitigating the erosive power of said side plume. A test was conducted on a low-power Hall thruster with and without integrated plume shield and the effect on thruster performance and plume characteristics were measured. Collected data shows that the thruster performed identically to within uncertainty in terms of thrust, specific impulse, and discharge oscillation characteristics. Plume measurements showed up to a 48% reduction in ion current density when averaging over 80° to 105° from the firing axis. A brief analytical study was performed to determine the advantages and disadvantages of using integrated plume shield as opposed to using spacecraft surface covering and placing thrusters on booms. The integrated plume shield was found to provide varying level of advantages in mass, design restrictions, and complexity, which are likely to lead to major cost savings in the long term.

Electric Propulsion↗
NASA NTRSDate not supplied

Sub-kW Class Hall-Effect Thruster Power Processing Unit for Wide Output Range Applications

The National Aeronautics and Space Administration (NASA) Small Spacecraft Electric Propulsion (SSEP) project is maturing high-propellant throughput sub-kilowatt Hall-effect thruster technologies to enable small spacecraft deep space science and exploration missions with high delta-v requirements. In support of this effort, development of a power processing unit (PPU) capable of providing discharge power of up to 1 kW continues to be pursued at the NASA Glenn Research Center (GRC). Previous reported work included a successful integrated test of a scalable, modular breadboard discharge power supply with the NASA-H64M laboratory model Hall-effect thruster and presentation of notional designs for the various auxiliary power supplies needed for thruster operation. Since that time, auxiliary power supply designs have been completed and fabricated, with the cathode heater and keeper power supplies being successfully tested with a hollow cathode assembly (HCA) in the NASA GRC Vacuum Facility 56 (VF-56). The desire for a lower mass, higher efficiency, and more versatile PPU to maximize performance of power and mass-limited small spacecraft has led to the exploration of a discharge power supply based on a series-parallel (LCC) resonant topology. This topology has enabled the discharge power supply to operate over a wider output range at switching frequencies 4-5 times higher than previous design iterations. Simulation models of the topology have been developed and a breadboard of the topology has been fabricated and evaluated on both resistive loads and an integrated Hall thruster test. This paper will present collected performance and integrated test data from both the fabricated auxiliary and resonant discharge power supplies. Advantages of the resonant converter architecture over more traditional pulse-width modulated (PWM) techniques in Hall-effect thruster discharge power supply applications will also be described.

electric propulsion↗