Search NASA⌕ Search

Engineering topics

Gad-El-hak, Mohamed

Publications and source records attributed to Gad-El-hak, Mohamed.

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Status and outlook of flow separation control

Under certain conditions, wall-bounded flows separate. To improve the performance of natural or man-made flow systems, it may be beneficial to delay or advance this detachment process. The present article reviews the status and outlook of separation control for both steady and unsteady flows. Both passive and active techniques to prevent or to provoke flow detachment are considered and suggestions are made for further research.

Gad-El-hak, Mohamed↗
NASA NTRS1990

Transition control

A unified view of the different control methods available or contemplated to delay or advance transition is presented. Emphasis is placed on two-dimensional incompressible flows, although more complex situations are also briefly covered. The governing equations are developed first, the routes to transition are mapped, and elements of the linear stability theory are outlined. The four basic stability modifiers - wall motion, suction, shaping, and wall heat transfer - are discussed, along with wave cancellation. The benefits as well as drawbacks of each approach are considered.

Gad-El-hak, Mohamed↗
NASA NTRS1989

Feasibility of generating an artificial burst in a turbulent boundary layer, phase 2

Various drag accounts for about half of the total drag on commercial aircraft at subsonic cruise conditions. Two avenues are available to achieve drag reduction: either laminar flow control or turbulence manipulation. The present research deals with the latter approach. The primary objective of Phase 2 research was to investigate experimentally the feasibility of substantially reducing the skin-friction drag in a turbulent boundary layer. The method combines the beneficial effects of suction and a longitudinally ribbed surface. At a sufficiently large spanwise separation, the streamwise grooves act as a nucleation site causing a focusing of low-speed streaks over the peaks. Suction is then applied intermittently through longitudinal slots located at selected locations along those peaks to obliterate the low-speed regions and to prevent bursting. Phase 2 research was divided into two tasks. In the first, selective suction from a single streamwise slot was used to eliminate either a single burst-like event or a periodic train of artificially generated bursts in laminar and turbulent boundary layers that develop on a flat plate towed in a water channel. The results indicate that equivalent values of the suction coefficient as low as 0.0006 were sufficient to eliminate the artificially generated bursts in a laminar boundary layer.

Gad-El-hak, Mohamed↗
NASA NTRS1989

The art and science of flow control

The ability to actively or passively manipulate a flow field to effect a desired change is of immense technological importance. In this article, methods of control to achieve transition delay, separation postponement, lift enhancement, drag reduction, turbulence augmentation, or noise suppression are considered. Emphasis is placed on external boundary-layer flows although applicability of some of the methods reviewed for internal flows will be mentioned. Attempts will be made to present a unified view of the different methods of control to achieve a variety of end results. Performance penalties associated with a particular method such as cost, complexity, or trade-off will be elaborated.

Gad-El-hak, Mohamed↗
NASA NTRS1987

Turbulence control on an airborne laser platform

An active flow control device to generate large-scale, periodic structures in a turbulent shear flow is developed. Together with adaptive optics, the device may be used on airborne laser platforms to reduce or eliminate optical distortion caused by the turbulence in the aircraft's boundary layer. A cyclic jet issuing from a spanwise slot is used to collect the turbulent boundary layer for a finite time and then release all of the flow instantaneously in one large eddy that convects downstream. Flow visualization and hot-film probe measurements are used together with pattern recognition algorithms to demonstrate the viability of the flow control method. A flat plate towed in a water channel is used as a test bed. The instantaneous velocity signal is used to compute important statistical quantities of the random velocity field, such as the mean, the root-mean-square, the spectral distribution, and the probability density function. When optimized for a given boundary layer, it is shown that the cyclic jet will produce periodic structures that are similar to the random, naturally occurring ones. These structures seem to trigger the onset of bursting events near the wall of the plate. Thus, the present device generates periodic structures in both the outer and inner regions of a turbulent boundary layer.

Gad-El-hak, Mohamed↗
NASA NTRS1987

A drag reduction method for turbulent boundary layers

A novel method to reduce skin friction drag in a turbulent boundary layer is presented. The technique combines the beneficial effects of a longitudinally ribbed surface and suction. The streamwise grooves act as a nucleation site causing a focusing of low-speed streaks over the peaks. Suction is then applied intermittently through longitudinal slots located at selected locations along those peaks to obliterate the low-speed regions and to prevent bursting. During the first phase of the present research, selective suction from a single streamwise slot was used to eliminate either a single burst-like event or a periodic train of artificially generated bursts in laminar and turbulent boundary layers. The experiments were conducted using a flat plate towed in an 18-m water channel. Flow visualization and hot-film probe measurements were used together with pattern recognition algorithms to demonstrate the feasibility of the drag-reducing method.

Gad-El-hak, Mohamed↗
NASA NTRS1987

Turbulence control on airborne laser platform

An avctive flow control device to generate large-scale, periodic structures in a turbulent shear flow is developed. Together with adaptive optics, the device may be used on airborne laser platforms to reduce or eliminate optical distortion caused by the turbulence in the aircraft's boundary layer. A flat plate towed in a water channel is used as a test bed. A cyclic jet issuing from a spanwise slot is used to collect the turbulent boundary layer for a finite time during its 'on' period. When the jet is turned 'off', all of the turbulent fluid is released instantaneously in one large eddy that convects downstream. Flow visualization and hot-film probe measurements are used together with pattern recognition algorithms to demonstrate the viability of the flow control method. The instantaneous velocity signal is used to compute important statistical quantities of the random velocity field, such as the mean, the root-mean-square, the spectral distribution, and the probability density function. When optimized for a given boundary layer, the cyclic jet produces periodic structures that are qualitatively similar to the random, naturally occurring ones. These structures seem to trigger the onset of bursting events near the wall. Thus, the present device generates periodic structures in both the outer and inner regions of a turbulent boundary layer.

Gad-El-hak, Mohamed↗
NASA NTRS1987

Review of flow visualization techniques for unsteady flows

The purpose of this article is to review some of the novel flow visualization techniques that are particularly suited for studying unsteady flows. While many of these techniques were originally developed for steady flow fields, the present paper will emphasize applications to time-dependent flows. The flow visualization methods presented include those that make use of scattered light from small particles or foreign additives as well as those that make use of changes in the index of refraction.

Gad-El-hak, Mohamed↗