Search NASA⌕ Search

Engineering topics

Gaetan K Kenway

Publications and source records attributed to Gaetan K Kenway.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Numerical Investigation of C L,max Prediction on the NASA High-Lift Common Research Model

An assessment of a Hybrid RANS/LES (HRLES) approach for C L,max prediction is presented for the NASA High-Lift Common Research Model (CRM-HL). Both free air and wind tunnel configurations of the CRM-HL are investigated and the results are compared to the QinetiQ wind tunnel experiments and two other numerical approaches: Reynolds Averaged Navier-Stokes (RANS) and Wall-Modeled Large Eddy Simulations (WMLES). For the free-air configuration, HRLES is shown to address some of the known shortcomings with RANS and prevent inboard and outboard flow separation particularly in the region of C L,max and post-stall. To achieve these improvements over RANS, LES-appropriate grids and numerical discretizations are required. It was also found that when applying HRLES to a RANS best practice grid and numerics that the HRLES method significantly underperformed RANS. For the in-tunnel configuration, HRLES showed good agreement with the loads, surface pressure and oil-flow photographs obtained in the experiment. HRLES was able to improve upon the RANS simulations, which showed a sharp loss of lift at the two highest angles-of-attack due to large scale inboard and outboard separation on the wing, by correctly predicting the corner flow separation and showing remarkably close agreement in the flow topologies with the experiment.

TTT↗
NASA NTRS2023

Numerical Study on the Aerodynamics of an Iced Airfoil With Scale-Resolving Simulations

Scale-resolving simulations of the NACA 23012 airfoil with horn ice accretion on the leading edge are conducted using the hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (hybrid RANS/LES) and wall-modeled large-eddy simulation (WMLES) approaches implemented in the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework. Aerodynamic results at the Reynolds number of 1.8 million show good comparison with the experimental measurements at different angles of attack from pre-stall to post-stall regimes. The pressure plateaus caused by the flow separation and the recovery of pressure inside the separation bubble around the iced leading edge are well predicted with the scale-resolving simulations when sufficient grid resolution is used around the accreted ice. The unsteadiness of the turbulent flows around the iced airfoil is also examined through the turbulent kinetic energy with the Reynolds normal stress anisotropy. Kelvin–Helmholtz instability (KHI) arises at the shear layer triggered by the upper ice horn and leads to rapid laminar-to-turbulent transition over a large range of angle of attack. With the increase of the angle of attack, the region with high turbulence intensity induced by the unstable shear layer spreads quickly over the entire upper surface of the airfoil. The coherent KHI modes from the upper and lower ice horns are extracted using the spectral proper orthogonal decomposition (SPOD) technique. The SPOD modes extracted from the upper shear layer have large-scale variations in the spanwise direction and low-rank behavior where the energy of the leading SPOD mode at each Strouhal number of the KHI largely represents the total energy when the mode number in the spanwise direction is small.

ARMD↗
NASA NTRS2023

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗
NASA NTRS2023

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗
NASA NTRS2023

Evaluation of Voronoi Meshes for Large Eddy Simulations of High Lift Aerodynamics

Numerical sensitivity to 3 different Voronoi seeding methods is investigated for Large Eddy Simulations (LES). A second order accurate, non-dissipative finite volume discretization is used to systematically investigate the effects of different polyhedral Voronoi mesh types using a sequence of three canonical problems with increasing complexity. First, inviscid isentropic vortex propagation is studied to demonstrate the substantial reduction of errors for rhombic dodecahedron and truncated octahedral cell types over Cartesian hexagonal cells of identical spacing. Furthermore, the reduction of errors induced at cell-size transitions (grid-coarsening interfaces) due to Lloyd smoothing iterations is quantified. It is shown that by utilizing an appropriate viscous flux discretization, a constant coefficient subgrid scale model is sufficient for non-linear stability at the 2:1 cell-size transitions on polyhedral grids, although some further error reduction does occur when smoothing is utilized. Next, forced homogeneous isotropic turbulence at an asymptotically large Reynolds number is studied to demonstrate the non-dissipative character of the inviscid flux discretization, and the non-linear robustness and accuracy offered by the viscous flux discretization using a subgrid scale model for all three Voronoi grid types. Finally,Wall-Modeled Large Eddy Simulations (WMLES) are performed to study the high-lift aerodynamics on the McDonnell Douglas 30P30N multi-element airfoil at two distinct grid levels and for two distinct Voronoi cell types. The formulation is shown to predict the aerodynamic loading with high accuracy at all angles of attack when sufficient resolution is reached, and the hexagonal prism grid topology, while computationally more expensive, has higher effective resolution compared to the Cartesian grid topology with the same spacing.

TTT↗
NASA NTRS2023

Evaluation of Voronoi Meshes for Large Eddy Simulations of High Lift Aerodynamics

Numerical sensitivity to 3 different Voronoi seeding methods is investigated for Large Eddy Simulations (LES). A second order accurate, non-dissipative finite volume discretization is used to systematically investigate the effects of different polyhedral Voronoi mesh types using a sequence of three canonical problems with increasing complexity. First, inviscid isentropic vortex propagation is studied to demonstrate the substantial reduction of errors for rhombic dodecahedron and truncated octahedral cell types over Cartesian hexagonal cells of identical spacing. Furthermore, the reduction of errors induced at cell-size transitions (grid-coarsening interfaces) due to Lloyd smoothing iterations is quantified. It is shown that by utilizing an appropriate viscous flux discretization, a constant coefficient subgrid scale model is sufficient for non-linear stability at the 2:1 cell-size transitions on polyhedral grids, although some further error reduction does occur when smoothing is utilized. Next, forced homogeneous isotropic turbulence at an asymptotically large Reynolds number is studied to demonstrate the non-dissipative character of the inviscid flux discretization, and the non-linear robustness and accuracy offered by the viscous flux discretization using a subgrid scale model for all three Voronoi grid types. Finally, Wall-Modeled Large Eddy Simulations (WMLES) are performed to study the high-lift aerodynamics on the McDonnell Douglas 30P30N multi-element airfoil at two distinct grid levels and for two distinct Voronoi cell types. The formulation is shown to predict the aerodynamic loading with high accuracy at all angles of attack when sufficient resolution is reached, and the hexagonal prism grid topology, while computationally more expensive, has higher effective resolution compared to the Cartesian grid topology with the same spacing.

TTT↗
NASA NTRS2023

Unsteady RANS and Scale Resolving Simulations of Open Rotor Noise

Computational simulations using structured curvilinear overset grids with the Launch Ascent and Vehicle Aerodynamics (LAVA) framework are presented for predicting the aerodynamic and aeroacoustic behavior of a contra-rotating open rotor (CROR) propulsion system using a newly developed and computationally efficient sliding mesh technique. A comprehensive evaluation of two turbulence closure treatments is carried out as part of the scope of this work: Unsteady Reynolds-Averaged Navier-Stokes Simulation (URANS), and Hybrid RANS/LES (HRLES). The computed results are then validated against existing experimental measurements at both the nominal take-off and cruise flight conditions. To propagate the noise generated by the near-field CROR system, aeroacoustic analysis based on a frequency-domain permeable surface Ffowcs Williams-Hawkings (FW-H) approach is applied.

ARMD↗
NASA NTRS2023

Unsteady RANS and Scale Resolving Simulations of Open Rotor Noise

Computational simulations using structured curvilinear overset grids with the Launch Ascent and Vehicle Aerodynamics (LAVA) framework are presented for predicting the aerodynamic and aeroacoustic behavior of a contra-rotating open rotor (CROR) propulsion system using a newly developed and computationally efficient sliding mesh technique. A comprehensive evaluation of two turbulence closure treatments is carried out as part of the scope of this work: Unsteady Reynolds-Averaged Navier-Stokes Simulation (URANS), and Hybrid RANS/LES (HRLES). The computed results are then validated against existing experimental measurements at both the nominal take-off and cruise flight conditions. To propagate the noise generated by the near-field CROR system, aeroacoustic analysis based on a frequency-domain permeable surface Ffowcs Williams-Hawkings (FW-H) approach is applied.

ARMD↗
NASA NTRSDate not supplied

Structured Overset and Unstructured Grid Simulations for the Third AIAA Sonic Boom Prediction Workshop

Predictions using the Launch Ascent and Vehicle Aerodynamics (LAVA) Unstructured and Structured Curvilinear solvers for the Biconvex and C608 geometries are compared in support of the 3rd AIAA Sonic Boom Prediction workshop. Description of the mesh generation techniques and numerical methods are provided along with a comparison of nearfield and far-field predictions with available experimental data as well as other workshop sub-missions. Strong consistency was observed between the Biconvex and C608 nearfield predictions across the two solvers used for this study, as well as validation and verification data. Additionally, near-field and farfield ground signature results using a combination of a truncated computational fluid dynamics (CFD) domain coupled to a mid-field space marching method and propagated to the ground using sBOOM will be discussed. This approach is shown to provide an efficient way to propagate near-field pressure signatures to the ground with the same accuracy as the near-field CFD coupled to sBOOM, but at less computational cost.

CST↗
NASA NTRSDate not supplied

Fluid-Structure Interaction Simulations of the ASPIRE SR01 Supersonic Parachute

High-fidelity computational fluid dynamics (CFD) simulations have so far only played exploratory and supporting roles in the study and qualification of parachutes for planetary entry. The last few years have seen the maturation of coupled computational methods that are capable of modeling the complex fluid-structure interactions between a parachute canopy and the supersonic flow in the wake of an entry vehicle in flight conditions. One of the primary goals of these methods is to predict the peak opening load experienced by the parachute during inflation. The Launch, Ascent, and Vehicle Aerodynamics (LAVA)team is developing efficient, high-fidelity numerical methods to perform such challenging fluid-structure interaction simulations. A loose coupling approach is used to advance the solutions of a Cartesian ghost cell immersed boundary method CFD solver and a finite element computational structural dynamics (CSD) solver in space and time. The coupled solver is employed to simulate the ASPIRE SR01 flight test, where a build-to-print version of the Mars Science Laboratory parachute was inflated in supersonic conditions in the upper terrestrial atmosphere. The simulations conducted in the current paper predict a peak opening load that is within 10% of that from the flight test. Grid convergence with respect to the volume and structural domains is demonstrated, and less than 1% variation in the peak opening load is predicted between all grid resolutions.

ARMD↗
NASA NTRSDate not supplied

High-Lift Common Research Model: RANS, HRLES and WMLES Perspectives for CLmax Prediction Using LAVA

A unified assessment of three turbulence treatments: Reynolds Averaged Navier-Stokes(RANS), Hybrid RANS/LES (HRLES) and Equilibrium Wall-Modelled Large Eddy Simulation(WMLES) is presented for the High-Lift Common Research Model (CRM-HL). For the free-air configuration, steady-state RANS simulations show very accurate drag polar predictions in the low-𝛼linear regime. However, strong grid sensitivity is reported near the maximum lift-state(𝐶𝐿max), with finer-grids showing larger errors and predicting erroneous flow topologies on the wing. Our RANS simulations show that several corrections for the Spalart-Allmaras (SA)turbulence model widely used in the community lead to more erroneous results compared to the baseline closure, without exception. Both scale-resolving methods (HRLES and WMLES)address these drawbacks and predict an outboard separation pattern on the main element that is in good agreement with the oil flow photographs taken from the QinetiQ wind tunnel experiments, when LES-appropriate grids and numerical discretizations are used. While RANS simulations with the baseline SA closure do not show any wing-root separation post𝐶𝐿max, both HRLES and WMLES show onset of corner flow separation with varying degrees of progression, along with a weak pitch break in the wing-contribution of the overall pitching moment. This post-𝐶𝐿max pitch break seen in the free-air simulations is weaker than the break observed in experiments, with a weaker break reported in WMLES for each iteration of grid-refinement. In-tunnel simulations using both SA-baseline RANS and WMLES show a much stronger post-𝐶𝐿max break with the WMLES predictions showing excellent agreement with the experiment in terms of both the flow-topology observed and the pressure-coefficients at various spanwise stations. Sensitivity to the tunnel wall boundary layer is characterized via comparisons between viscous and inviscid treatments for the tunnel walls. WMLES predictions show moderate sensitivity at the predicted inboard flow-state at 𝐶𝐿max along with the progression towards a post-𝐶𝐿max stall; however, this stalled state at 𝛼≈20◦(inside the tunnel) obtained with both tunnel wall treatments appears to be largely identical.

TTT↗
NASA NTRSDate not supplied

A Hybrid RANS-LES Perspective for the High Lift Common Research Model Using LAVA

An assessment of a Hybrid RANS/LES (HRLES) approach for𝐶𝐿,max prediction is presented for the NASA High-Lift Common Research Model (CRM-HL). Both the free air and the wind tunnel configuration of the CRM-HL are investigated and the results are compared to the QinetiQ wind tunnel experiments and to two other numerical approaches: Reynolds Averaged Navier-Stokes (RANS) and Wall-Modeled Large Eddy Simulations (WMLES). For the free-air configuration, HRLES was shown to address some of the known shortcomings in RANS methods and prevent inboard and outboard flow separation particularly in the region of𝐶𝐿,max and post-stall. To achieve these improvements over RANS, LES-appropriate grids and numerical discretizations are required. HRLES predicts a weak pitch break at the highest angle-of-attack due to onset of wing-root corner flow separation whereas the free-air corrected experiment values indicate an occurrence of a much stronger pitch break. The improvements of HRLES over a URANS approach has been objectively shown by computing a set of solutions with the same grid, same numerics and time-step size and comparing the solutions. It was also found that when applying HRLES to a RANS best practice grid and numerics that the HRLES method significantly under performed RANS. For the in tunnel configuration, HRLES showed good agreement with the loads, surface pressure and oil-flow photographs obtained in the experiment. HRLES was able to improve upon the RANS simulations, which showed a sharp loss of lift at the two highest angles-of-attack due to large scale inboard and outboard separation on the wing, by correctly predicting the corner flow separation and showing remarkably close agreement in the flow topologies with the experiment.

TTT↗
NASA NTRSDate not supplied

Predictions of LAGOON Nose Landing Gear Flow and Noise Using Wall-Modeled Large-Eddy Simulations

Wall-modeled large-eddy simulations (WMLESs) of the LAGOON nose landing gear are conducted with compressible Navier–Stokes equations and immersed boundary technique using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework. The simulations are conducted using six different Cartesian octree meshes for the grid sensitivity analysis of the near-field and far-field numerical predictions, where the far-field noise results are computed with the Ffowcs Williams–Hawkings acoustic analogy. The effects of numerical tripping induced at the exact locations of the tripping devices in the experiments are also examined. In general, better comparison with the experimental results are shown for the the near-field results obtained with the simulations under the effects of numerical tripping. The effects of tripping are not significant on the far-field noise calculations and the results have reasonable comparison with the experimental data in the low and medium frequency ranges when an impermeable formulation of the acoustic analogy is used.

CST↗