Search NASA⌕ Search

Engineering topics

Gaetan K. Kenway

Publications and source records attributed to Gaetan K. Kenway.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Scale resolving simulations of the NASA Juncture Flow Model using the LAVA solver

Two distinct simulation methodologies: Delayed Detached Eddy Simulation (DDES) and stress based Wall-modelled Large Eddy Simulation (WMLES) are evaluated using structured overset curvilinear grids for the NASA juncture flow model. While both methodologies are shown to mitigate the primary shortcomings of steady state Reynolds Averaged Navier Stokes(RANS) simulations, several unresolved aspects are identified. Strong sensitivity to RANS-typegrid refinement is observed in the DDES with a substantial deterioration of the solution quality with increasing spatial resolution associated with deficiencies in the shielding function. Mean profiles for attached boundary layers on the fuselage show spurious inflections suggesting modelled stress depletion on finer grids. Lower numerical dissipation in terms of spatial discretization and time step size is seen to improve the solution quality, and the advantage of using RC and QCR2000 corrections in the underlying RANS closure is demonstrated for DDES on RANS-type meshes. Equilibrium Wall-Modelled LES used grids that resolved the tripping dots over the fuselage nose and the wing leading edge, consistent with the experiment setup. These simulations resulted in a cost-competitive approach compared to DDES on RANS-type grids. Although the agreement between WMLES predictions of first and second order single point statistics with experimental measurements is promising, a fundamental shortcoming is noted in terms of an overshoot in streamwise momentum in corner regions of the wing-fuselage juncture. This excess momentum subsequently delays the onset of separation,thereby resulting in an underprediction in length of the separation bubble. Some quantitative sensitivity to numerical discretization is observed; lowering of numerical dissipation shows better agreement with the experiment.

T^3↗
NASA NTRSDate not supplied

Transonic Lift and Drag Predictions using Wall Modelled Large Eddy Simulations

Wall-modelled Large Eddy Simulations (WMLES) of the NASA Common Research Model (CRM) at transonic conditions and various angles of attacks leading up to and including shock-induced flow separation are performed using the LAVA computational framework. The simulations are shown to accurately predict the lift curve slope and the onset of separation characterized by the break in the pitching moment. Furthermore, careful assessment of skin-friction drag at cruise condition and its subsequent decrease with increasing angles of attack are shown to be in agreement with viscous sublayer resolving Reynolds Averaged Navier Stokes(RANS) simulations. The small differences between WMLES and RANS appear to be of the same order as differences seen between two RANS models at the cruise-point. Some sensitivity is observed to the coefficient used in the subgrid scale model, although this can be reconciled by noting the low chord- and shock-incidence Reynolds numbers (Rex≈106) seen in the outboard regions of the wing, along with the uncertainties associated with tripping and the numerical transition that occurs near the leading edge. Among the primary drawbacks seen in the WMLES predictions is the subdued increase in wave-drag with increasing angle-of-attack and the shock intensity when compared with experimental data. Preliminary assessment suggests that additional span- and stream-wise grid resolution is likely needed in mid- and out-board portions of the wing to better resolve the shock-induced separated flow and to further investigate prediction accuracy of unsteady temporal characteristics of the problem.

ARMD↗
NASA NTRSDate not supplied

Preliminary Assessment of a Distributed Electric Propulsion System for the SUSAN Electrofan

The SUSAN Electrofan is a new hybrid electric large regional jet aircraft concept being studied by NASA that leverages advanced propulsion system technologies such as distributed electric propulsion (DEP) and boundary-layer ingestion (BLI) to reduce fuel consumption and emissions. In order to evaluate the individual benefits of these technologies toward the SUSAN Electrofan’s wing-mounted propulsion systems, three configurations are proposed. The first consists of two underwing pylon-mounted podded propulsors and serves as a baseline, while the second features an underwing pylon-mounted DEP concept with 16 ducted fans in a mail-slot nacelle. The third and final configuration mounts the mail-slot nacelle directly onto the pressure side of the wing to also take advantage of BLI. This paper presents preliminary investigations into the design and performance of the first two propulsion system configurations. This begins with an initial propulsor and mail-slot design where the aeropropulsive design space is explored, and adverse effects are addressed through iterative geometry modifications. The propulsion system configurations are then installed onto a wing–body model to account for integration effects and assess the relative aerodynamic and shaft power performance of each concept. Results indicate the potential benefits of DEP, which come from significant reductions in total drag, provided by operation at much lower propulsor fan pressure ratios.

ARMD↗