Search NASA⌕ Search

Engineering topics

Gaffney, J.

Publications and source records attributed to Gaffney, J..

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Correlations between asymmetric compression, burn amplification, and hot-spot velocities in inertial confinement fusion implosions

Here, this manuscript examines the correlations between the hot-spot velocity (an observable signature of residual kinetic energy), low-mode implosion asymmetries, and burn amplification in inertial confinement fusion implosions on the National Ignition Facility (NIF). Using a combination of two-dimensional axis-symmetric and three-dimensional radiation-hydrodynamic simulations coupled to neutronics, we find that for typical NIF implosions, the stagnation asymmetry multiplies the observed hot-spot velocity anywhere from 80% to 120%, while burn amplification always increases it. Additionally, we find stagnation asymmetry typically deflects the observed hot-spot flow. The two mechanisms (low-mode implosion asymmetries and burn amplification) can be decoupled, and application of a simple model to a database of cryogenic implosions on the NIF infers the total hot-spot velocity amplification. This finding modifies the interpretation of data collected from inertial confinement fusion experiments and impacts the magnitude and origin of low-mode asymmetries.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Alpha heating of indirect-drive layered implosions on the National Ignition Facility

We report in order to understand how close current layered implosions in indirect-drive inertial confinement fusion are to ignition, it is necessary to measure the level of alpha heating present. To this end, pairs of experiments were performed that consisted of a low-yield tritium–hydrogen–deuterium (THD) layered implosion and a high-yield deuterium–tritium (DT) layered implosion to validate experimentally current simulation-based methods of determining yield amplification. The THD capsules were designed to reduce simultaneously DT neutron yield (alpha heating) and maintain hydrodynamic similarity with the higher yield DT capsules. The ratio of the yields measured in these experiments then allowed the alpha heating level of the DT layered implosions to be determined. The level of alpha heating inferred is consistent with fits to simulations expressed in terms of experimentally measurable quantities and enables us to infer the level of alpha heating in recent high-performing implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Burning plasma achieved in inertial fusion

The achievement of obtaining a burning plasma is a critical step toward self-sustaining fusion energy. A burning plasma is a fusion plasma where the alpha-particles created by the deuterium-tritium (DT) fusion reactions are the primary source of heating in the plasma, which is necessary to sustain and propagate the fusion reaction to enable high energy gain. After decades of fusion research, a burning plasma state has finally been achieved. Herein, we report upon the first burning-plasma experiments; this state was achieved using a strategy to increase the capsule spatial scale via two different implosion concepts, on the US National Ignition Facility. These experiments show energies from self-heating in excess of the mechanical work injected into the implosions satisfying several burning plasma metrics, the last experiment additionally shows that the fusion self-heating is greater than losses from radiation and heat conduction. These experiments triple the fusion yield performance and show significantly higher yield amplification from self-heating than prior results; remaining degradations can be reduced for even higher fusion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Hotspot conditions achieved in inertial confinement fusion experiments on the National Ignition Facility

We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗