Engineering topics

Gale, R. P.

Publications and source records attributed to Gale, R. P..

9 records

NASA NTRS1991

GaAs (AlGaAs)/CuInSe2 tandem solar cells. Technology status and future directions

Mechanically stacked, high efficiency, lightweight, and radiation resistant photovoltaic cells based on a GaAs thin film top and CuInSe2 thin film bottom cells were developed, and are considered one of the most promising devices for planar solar array applications. The highest efficiency demonstrated so far using the 4 sq cm design is 23.1 pct. AM0, one sun efficiency when measured in four-terminal configuration. The current status of the GaAs(AlGaAs)/CuInSe2 tandem cell program is presented and future directions that will lead to cell efficiencies higher than 26 pct. Air Mass Zero (AM0). A new 8 sq cm cell design developed for a two terminal and voltage matched configuration to minimize wiring complexity is discussed. Optimization of the GaAs structure for a higher end-of-life performance and further improvement of tandem cells by utilizing AlGaAs as an top absorber are described. Results of environmental tests conducted with these thin film GaAs/CuInSe2 tandem cells are also summarized.

Kim, N. P.↗

NASA NTRS1991

Progress in GaAs/CuInSe2 tandem junction solar cells

Much more power is required for spacecraft of the future than current vehicles. To meet this increased demand for power while simultaneously meeting other requirements for launch, deployment, and maneuverability, the development of higher-efficiency, lighter-weight, and more radiation resistant photovoltaic cells is essential. Mechanically stacked tandem junction solar cells based on (AlGaAs)GaAs thin film CLEFT (Cleavage of Lateral Epitaxial Film for Transfer) top cells and CuInSe2(CIS) thin film bottom cells are being developed to meet these power needs. The mechanically stacked tandem configuration is chosen due to its interconnect flexibility allowing more efficient array level performance. It also eliminates cell fabrication processing constraints associated with monolithically integrated multi-junction approaches, thus producing higher cell fabrication yields. The GaAs cell is used as the top cell due to its demonstrated high efficiency, and good radiation resistance. Furthermore, it offers a future potential for bandgap tuning using AlGaAs as the absorber to maximize cell performance. The CuInSe2 cell is used as the bottom cell due to superb radiation resistance, stability, and optimal bandgap value in combination with an AlGaAs top cell. Since both cells are incorporated as thin films, this approach provides a potential for very high specific power. This high specific power (W/kg), combined with high power density (W/sq m) resulting from the high efficiency of this approach, makes these cells ideally suited for various space applications.

Kim, N. P.↗

NASA NTRS1990

23.5 percent thin-film space concentrator cells

Thin-film AlGaAs-GaAs double-heterostructure concentrator cells were fabricated which exhibit total-area conversion efficiencies as high as 23.5 percent AM0 at 100 suns, 25 C. This is one of the best space concentrators measured to date at NASA and is designed for a thin-film cell without a prismatic coverglass. This solar cell structure consists of a GaAs/AlGaAs film less than 5 micron thick mounted to a glass cover/superstrate, with coplanar back-side contacts. The coverglass is not prismatic. The CLEFT process, a method for mechanically separating epitaxial layers from their substrate, is used to process these cells into thin films. The advantages of single-crystal GaAs are thereby retained, while reducing weight and cutting cost by allowing for substrate reuse. Thin-film cells also have better thermal management capabilities and can be stacked for use in tandem structures. Cell fabrication and performance are described, and directions for further improvements are identified.

Dingle, B. D.↗

NASA NTRS1989

Concepts for thin-film GaAs concentrator cells

The development of advanced GaAs concentrator solar cells, and in particular, the use of CLEFT (cleavage of lateral epitaxial films for transfer) processes for formation of thin-film structures is reported. The use of CLEFT has made possible processing of the back, and cells with back surface grids are discussed. Data on patterned junction development are presented; such junctions are expected to be useful in back surface applications requiring point contacts, grating structures, and interdigitated back contacts. CLEFT concentrator solar cells with grids on the front and back surfaces are reported here; these cells are 4 microns thick and are bonded to glass covers for support. Air mass zero efficiency of 18.8 percent has been obtained for a CLEFT concentrator operating at 18.5 suns.

Spitzer, M. B.↗

NASA NTRS1987

GaAs/AlGaAs heterostructure point-contact concentrator cells

Point-contact cells fabricated in silicon have recently achieved very high efficiencies. Applying this structure to GaAs is difficult as it requires both surface passivation of the GaAs and a film of GaAs with thickness less than 10 microns. The authors propose to overcome these difficulties by (1) using AlGaAs layers grown by OMCVD to act as front- and back-surface fields in order to confine the photogenerated minority carriers away from the surfaces, and (2) using the CLEFT technology to produce thin, separated films of this structure. It has been found that much of the necessary technologies have been developed and that the primary problem remaining to be solved is localized junction formation.

Gale, R. P.↗

NASA NTRS1985

High-efficiency double-heterostructure AlGaAs/GaAs solar cells

Double-heterostructure solar cells have been fabricated from wafers prepared by using organometallic chemical vapor deposition to grow a p GaAs absorbing layer sandwiched between p(+) and n(+) AlGaAs layers. The best cell, which incorporates an abrupt AlGaAs/GaAs shallow heterojunction, exhibits a global AM1 one-sun conversion efficiency of 23 percent. The rate at which the open-circuit voltage decreases with increasing temperature is lower for the double-heterostructure cells than for GaAs shallow-homojunction cells.

Gale, R. P.↗

NASA NTRS1984

Efficient AlGaAs shallow-homojunction solar cells

Shallow-homojunction n+/p/p+ solar cells with one-sun, AM1 conversion efficiencies as high as 12.9 percent have been fabricated in Al0.2Ga0.8As epitaxial layers grown by organometallic chemical vapor deposition on single-crystal GaAs substrates. For these cells, which have n+ layers thinned by anodic oxidation to about 500 A, the quantum efficiencies in the short-wavelength portion of the spectrum are as high as the best reported for AlGaAs cells with high band-gap window layers.

Gale, R. P.↗

NASA NTRS1984

A new high-efficiency GaAs solar cell structure using a heterostructure back-surface field

Shallow-homojunction GaAs solar cells are fabricated with a back-surface field (BSF) produced by a GaAs/Al(0.2)Ga(0.8)As heterostructure. These cells exhibit higher open-circuit voltages and conversion efficiencies than control cells made with a p-GaAs/p(+)-GaAs BSF. Conversion efficiencies of over 22 percent (AM1, total area) have been obtained with this new structure. The use of a higher bandgap material below the active region not only provides an enhanced BSF but will also permit the implementation of two solar-cell designs: a GaAs cell with a back-surface reflector and an AlGaAs cell that can be used as the upper cell in tandem configurations.

Gale, R. P.↗

NASA NTRS1982

Lateral epitaxial overgowth of GaAs by organometallic chemical vapor deposition

Lateral epitaxial overgrowth of GaAs by organometallic chemical vapor deposition has been demonstrated. Pyrolytic decomposition of trimethylgallium and arsine, without the use of HCl, was used to deposit GaAs on substrates prepared by coating (110) GaAs wafers with SiO2, then using photolithography to open narrow stripes in the oxide. Lateral overgrowth was seeded by epitaxial deposits formed on the GaAs surfaces exposed by the stripe openings. The extent of lateral overgrowth was investigated as a function of stripe orientation and growth temperature. Ratios of lateral to vertical growth rates greater than five have been obtained. The lateral growth is due to surface-kinetic control for the two-dimensional growth geometry studied. A continuous epitaxial GaAs layer 3 microns thick has been grown over a patterned mask on a GaAs substrate and then cleaved from the substrate.

Gale, R. P.↗