Search NASA⌕ Search

Engineering topics

Gallagher, Ryan C.

Publications and source records attributed to Gallagher, Ryan C..

At least 19 records

Variable gap thermal conductivity apparatus and method

An apparatus and a method for determining the thermal conductivity of a fluid specimen are provided. The apparatus and the method include determining thermal conductivity using a quasi-steady state variable gap axial flow technique. The fluid specimen is heated on one side by a heat source with a known power output and cooled on the other side. After reaching steady state, a resulting temperature drop through the fluid specimen exists. This temperature drop, the known fluid specimen thickness (or gap distance), and the known power output are used to calculate the thermal resistance of the fluid specimen. The thermal conductivity of the fluid specimen is then determined using a curve fit of thermal resistance with respect to gap distance.

Gallagher, Ryan C.↗

Simulation of a TRISO MiniFuel irradiation experiment with data-informed uncertainty quantification

An irradiation experiment using tristructural isotropic (TRISO) fuel particles and the miniature fuel (MiniFuel) irradiation vehicle was performed in Oak Ridge National Laboratory’s High Flux Isotope Reactor (HFIR) to support development of the Kairos Power fluoride salt–cooled, high-temperature reactor (KP-FHR). Here, this paper describes modeling predictions of temperatures and fuel burnup for the as-built experiment. An uncertainty quantification (UQ) analysis was performed to determine the effect of TRISO particle volume and position on the temperature predictions at various fuel heat generation rates (HGRs). This UQ study utilized fuel kernel position and volume measurements previously collected using X-ray computed tomography (XCT) techniques and Monte Carlo sampling methods to generate fuel compact cases that were then analyzed using a finite element thermal model. The UQ analysis indicated that uncertainty in calculated temperatures caused by varying TRISO particle arrangement is relatively small, even at high fuel HGR. Final predictions of particle temperatures throughout the irradiation are shown to be relevant to KP-FHR normal and off-normal operating conditions and to previous TRISO irradiation experiments. The combination of XCT with UQ analyses will inform post-irradiation examination (PIE) of the irradiated fuel compacts, and these analyses can be used to develop fuel performance models for coated particle fuel forms. Both PIE of separate-effects irradiation data and enhanced fuel performance modeling support accelerated qualification of TRISO fuels for a broad range of advanced reactor applications. The novel approach demonstrated here of measuring TRISO particle configurations with XCT methods and generating representative fuel compacts for finite element modeling and UQ analysis could be leveraged by the broader particle fuel community in the development of other TRISO fuel experiments in which these variables may have a significant impact on key outcomes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FY2022 Progress Report on Viscosity and Thermal Conductivity Measurements of Molten Salts

This report describes the development of and experimental measurements made with the thermal conductivity and viscosity measurement systems for molten salts at Oak Ridge National Laboratory. The thermal conductivity system is based on a steady-state measurement technique in which a heat flux is driven across a variable gap, and the changes in temperature difference across the gap are measured as the gap size is varied. The system comprises an inner containment, which possesses the heating element, and an outer containment, which possesses the salt specimen and cooling channels. The gap is formed between the outer bottom of the inner containment and the inner bottom of the outer containment. The viscosity system is based on the falling-ball technique in which a salt-filled tubular crucible is fixed at an angle and a ball rolls through the salt. The terminal velocity of the ball can be converted into viscosity via a calibration factor calculated for crucible-ball combinations which account for thermal expansion and flow characteristics. Modifications were made to both systems this fiscal year. Modifications to the thermal conductivity system included adding guard heaters to prevent axial heating losses, and modifications to the viscosity system included changing the crucible design to prevent air pocket formation and providing the ability to conduct measurements with a glass or steel crucible.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Assessment of Molten Eutectic LiF-NaF-KF Density through Experimental Determination and Semiempirical Modeling

Molten salts have favorable material properties for use in high-temperature energy systems, including thermal energy storage systems, concentrating solar power plants, nuclear reactors, and various industrial manufacturing processes. Knowledge of chemical and thermophysical property data is essential for the design and optimization of these systems, yet data are often limited or uncertain for many candidate salts due to the difficulty of thermophysical property measurements at relevant temperatures (e.g., 500–900 °C). Here, the density of molten LiF-NaF-KF eutectic is reassessed through review of previous experimental data, new density measurements from 470 to 800 °C, and semiempirical modeling. Additionally, the density was measured using the displacement technique. Compositional and temperature-dependent density estimates were calculated with a multidimensional Redlich–Kister model. The results of the new experimental measurements agree within 2% of the modeled density of molten eutectic LiF-NaF-KF. The Redlich–Kister model’s prediction shows a near-ideal density behavior for the LiF-NaF-KF system and is promising for the estimation of off-eutectic LiF-NaK-KF densities. Finally, through review of the existing literature and comparison to new measurements, recommendations are made for the density of LiF-NaF-KF.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design and performance of a variable gap system for thermal conductivity measurements of high temperature, corrosive, and reactive fluids

We report high-temperature fluids such as molten salts, liquid metals, and gasses are being proposed for many advanced energy systems including thermal energy storage devices, concentrating solar plants, and advanced nuclear reactor designs. However, the chemical behavior and thermophysical properties of many of these fluids have not been well characterized, which hinders the design, modeling, safety analysis, and deployment of these systems. Thermal conductivity is a property that is especially limited by existing measurement capabilities, which are subject to errors caused by convection, material interaction, radiative heat transfer, and instrument degradation. Therefore, there is a lack of standard, systematic measurement techniques for high-temperature, reactive, and corrosive fluids. In this work, the development of a variable gap thermal conductivity measurement system is detailed. The system is designed to measure the thermal conductivity of highly corrosive and reactive fluids, and survive operation between 100 °C and 800 °C. The effects of convection are minimized by limiting the thickness of the specimen to thin sizes (<0.3 mm). Corrections for radiative heat transfer were included in the working equations to consider specimens with varying optical properties. The design, construction, instrumentation, operating principles, and data analysis techniques are discussed in detail. The system was tested up to 500 °C using helium gas and molten KNO 3 -NaNO 3 to verify the measurement technique and determine the sources of error. At 300 and 400 °C KNO 3 -NaNO 3 , results showed maximum relative error of 6% when compared to results in the literature. The helium results were within 13% of those in the literature at 300 and 400 °C. Higher errors were observed at 500 °C for both fluids, and the sources of these errors are discussed.

42 ENGINEERING↗

Investigation of the thermal conductivity of molten LiF-NaF-KF with experiments, theory, and equilibrium molecular dynamics

Molten salts are being proposed for numerous advanced energy applications, including advanced nuclear reactors, concentrating solar power plants, thermal energy storage, and fusion reactors. Accurate knowledge of the thermophysical properties of molten salts directly impact the performance of these energy systems and are essential for design and safety analyses. Thermal conductivity data for fluoride molten salts and mixtures are especially lacking. In this work, experimental measurements of thermal conductivity using the steady-state variable gap technique were performed on eutectic LiF-NaF-KF from 834 to 1195 K. The experiment accounts for radiative, convective, and conductive heat losses. In addition, theoretical and molecular dynamics models are used, from 750 K up to 1300 K, to estimate the thermal conductivity for comparison with the experimental results. The results of experiments show a weak negative deviation of thermal conductivity with temperature, unlike previous experimental results in the literature. The measured thermal conductivity magnitudes agree with the theoretical and molecular dynamics predictions, aside from the data above 1100 K, where heat losses and radiative errors are the most significant, having a 16% maximum deviation from theory. These experimental results provide new thermal conductivity data for the LiF-NaF-KF system and further validation of the predictive models. The theoretical model was used to map the composition and temperature dependent thermal conductivity of LiF-NaF-KF and the mapping’s deviation from a linear additivity estimation of thermal conductivity. Additionally, this mapping showed the highest deviations from linearity for KF-LiF rich mixtures and increasing deviation with temperature. Notably, the deviation from linearity near the LiF-NaF-KF eutectic composition was around 25%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design of Temperature Dependent Critical Experiments with SPRF/CX

This paper describes the investigation of temperature-dependent critical experiments using the Seven Percent Critical Experiments (7uPCX) and Burnup Credit Critical Experiments (BUCCX) fuel types within the Sandia Pulsed Reactor Facility/Critical Experiments (SPRF/CX) apparatus at Sandia National Laboratories (Sandia). The goal of these experiments is to test the effect of varying system temperature on the $\kappa$ eff bias of water-moderated systems. Temperatures of 5–95°C were considered in this work. Eighteen representative lattice configurations were analyzed that had variations in the number of fuel rods and water holes, as well as in the array configuration, to achieve a variety of moderation regimes. The configurations were based on those detailed in the LEU-COMP-THERM-078 and LEU- COMP-THERM-079 experiments, both of which were published in the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Temperature Dependent Experiments using SPRF/CX [Slides]

A range of fuel arrays has been examined for both fuel types and representative arrays were selected. Temperature dependent calculations were performed to show the performance of the arrays. Modification to the SPRF/CX facility has been proposed to aid SNL staff in the execution of temperature dependent experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal Property Characterization of Molten Salt Reactor–Relevant Salts

The thermochemical and thermophysical properties of molten salt systems are necessary input for the design, licensing, and deployment of molten salt reactor concepts. The thermochemical and thermophysical property measurement capabilities being used and developed at Oak Ridge National Laboratory (ORNL) include liquid density, volumetric thermal expansion, viscosity, vapor pressure, phase behavior, and heat capacity and thermal conductivity measurement capabilities. Properties of eutectic LiF-NaF-KF (FLiNaK) and NaCl-KCl are being measured to validate the measurement techniques to be used to provide data to reactor developers and to better quantify the uncertainty of measurements. This report summarizes the status of thermal conductivity, viscosity, specific heat capacity, and density. A method for property estimation using Redlich Kister expansion is also described. This technique will be used to help validate measured properties and to guide future experiments by targeting mixtures or components for which data are uncertain or lacking.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Assembly of MiniFuel Targets for Irradiation of U-Mo Fuel Specimens in the High Flux Isotope Reactor

To support the development of advanced low-enriched uranium for use in nuclear reactors, irradiation testing of U-Mo disk specimens was performed at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) to collect experimental irradiation data on this type of fuel at pressurized water reactor–relevant temperatures. U-Mo is a uranium alloy that has superior dimensional stability relative to alpha-phase uranium metal and has a substantially higher uranium density compared to UO 2 . U-Mo disks specimens were fabricated at Idaho National Laboratory and inserted into MiniFuel targets for HFIR irradiation. Three MiniFuel targets were successfully assembled, welded, tested, and delivered to HFIR, along with their quality assurance documentation. The targets were inserted into HFIR’s inner vertical experiment facility within the permanent beryllium reflector. Each target contains six disk specimens and will be irradiated in HFIR for three, four, and eight cycles, with target temperatures between 250 and 500°C. This report summarizes the experiment design, test matrix, pre-characterization of specimens, and experiment assembly.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assembly of MiniFuel Targets for Irradiation of TRISO Fuel Compacts in the High Flux Isotope Reactor

To support the development of Kairos Power’s fluoride-salt-cooled high-temperature reactor, irradiation testing of tristructural isotropic (TRISO) fuel compacts was performed at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) to collect experimental data on TRISO fuel during high particle-power operation and validate fuel performance models. Fuel compacts containing enriched uranium oxycarbide (UCO), natural UCO (NUCO), or uranium dioxide (UO 2 ) TRISO particles were fabricated at ORNL and inserted into MiniFuel targets for HFIR irradiation. Five MiniFuel targets were successfully assembled, welded, tested, and delivered to HFIR, along with their quality assurance documentation. The targets were inserted into HFIR’s inner vertical experiment facility within the permanent beryllium reflector. Each target contains six fuel compacts and will be irradiated in HFIR for four cycles, with target temperatures of 500, 700, and 900°C. This report summarizes the experiment design, test matrix, and fabrication. This work was performed under the Nuclear Science User Facility program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Critical Experiment Design Phase 2 Report for Integral Request 304

This report documents the second phase of the critical experiment design process (CED-2) conducted as part of integral experiment request (IER) 304. The purpose of IER-304 is to develop a temperature-dependent critical experiment capability at the Sandia National Laboratories critical experiment facility using low-enriched uranium oxide fuel. Only a few benchmark quality critical experiments are currently available to validate criticality safety computational methods at temperatures other than room temperature. Recent advancements in computational techniques such as implementation of on-the-fly Doppler broadening techniques and advanced treatment of thermal scattering data necessitate the development of additional experimental capabilities in this area. The work described in this report developed representative configurations using 7uPCX and BUCCX fuels, analyzed the physics exercised by the different arrays, and analyzed the estimated experimental uncertainties. This report also scopes the information necessary for performing modifications to the reactor to accommodate operation at elevated and reduced temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis and Design for Irradiation of High Power TRISO Fuel Compact Specimens in HFIR

Tristructural isotropic (TRISO) fuel is being proposed for use in several high-temperature advanced reactor concepts because of its structural integrity under high operating temperatures and burnup. One of these advanced reactor concepts is the Kairos Power fluoride salt-cooled high-temperature reactor (KP- FHR) under development by Kairos Power, LLC. Previous TRISO irradiation experiments were focused on qualification for high-temperature gas reactors (HTGRs), which have higher operating temperatures but lower particle powers than the KP-FHR design. To study the performance of TRISO fuel designed for HTGRs under prototypical FHR conditions, a set of experiments was designed using the MiniFuel irradiation vehicle at the Oak Ridge National Laboratory’s (ORNL) High Flux Isotope Reactor (HFIR). The experiments will irradiate 30 TRISO-containing carbon matrix compacts at inner small vertical experiment facilities in HFIR. Each compact will contain 20 TRISO particles (600 particles total) developed for HTGRs, consisting of either 14% enriched uranium dioxide uranium carbide, naturally enriched uranium dioxide, uranium carbide, or 9.6% enriched uranium dioxide fuel kernels with time- and volume-averaged silicon carbide layer temperatures between 500 and 900°C. This report summarizes the vehicle designs that have been developed, as well as the neutronic and thermal analyses completed for these irradiation experiments. These analyses show that MiniFuel compact irradiation is a versatile experiment that can be used to study a range of TRISO particle powers and fuel types while providing reasonable separation of burnup and temperature effects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗