Engineering topics
Publications and source records attributed to Gamble, Kyle A.
I've been asked to give a brief overview of myself and the work I do at a virtual recruitment event with the University of South Carolina. I graduated from their in 2022 and the the recruitment asked if I could give a brief 10 min presentation.
In the event of cladding rupture, which could occur in light water reactor fuel assemblies during a loss-of-coolant accident (LOCA), fuel particles, along with fission gases, can be expelled into the reactor core from the fractured fuel rod. This expulsion of fragmented fuel particles, referred as fuel dispersal, is the subject of investigation to evaluate the safety implications of increasing fuel burnup in light water reactors, with a specific focus on fuel fragmentation, relocation, and dispersal. Particle trajectories and the resulting mass distribution of the settled particles within the reactor pressure vessel can pose a long-term cooling challenge for the reactor core. The fuel dispersal phenomenon is significantly influenced by the ejection characteristics of the fuel fragments, as well as the size and shape of the cladding rupture and fuel rod depressurization history during LOCA transients. In this study, the transport of fuel particles within a scaled 5 × 5 lattice of a pressurized water reactor rod bundle geometry is modeled through a two-fluid Eulerian framework that treats the gas and solid phases as interpenetrating continua. The required boundary conditions are evaluated from the fuel performance code BISON in a postulated large-break LOCA scenario. The modeling framework considers solid fuel particles as granular matter, interacting with the gaseous dry steam phase and fission gases through the governing interfacial momentum and energy exchange between the gas and solid phases. The simulation results provide the volume fraction of the solids settled on the bottom surface of the fuel bundle, quantifying the deposition within the bundle geometry.
The Bison fuel performance code has been under development at Idaho National Laboratory by various programs within the U.S. Department of Energy since 2009. As part of any fuel performance code development, validation is necessary. To this end, several Halden experiments have been used. Early on, the focus was on validating the thermal mechanical behaviour, including pellet cladding mechanical interaction and fission gas release models implemented in Bison. Support for design-basis accident capabilities began in approximately 2014. Also in 2014, the development of models for accident tolerant fuel (ATF) concepts also began. This includes dopedUO2 fuel for which Halden has some experiments with temperature and fission gas release measurements. The Bison team has been fortunate to have two senior developers be secondees to Halden for a year: the late Dr. Giovanni Pastore from May 2015 to April 2016 and the now retired Dr. Richard Williamson in 2018. The paper will provide examples of Bison validation using Halden data for standard UO2 fuel under normal operation and loss-of-coolant accident condition, and ATF concepts. A tribute to the legacy that both the late Giovanni and retired Richard left on the Bison code is provided.
Small Modular Reactors (SMRs) are actively being pursued by the international nuclear industry. The Bison fuel performance code developed at Idaho National Laboratory is a tool capable of analyzing the thermo-mechanical response and species diffusion for a wide variety of fuel types under both normal and accident conditions. Two of the fuel types considered for a wide range of SMRs are TRISO fuel particles and metallic fuel. This paper provides an overview of the capabilities in Bison for these fuel types with a few example studies relevant for the SMR industry.
An overview of NEAMS program activities to model fuel fragmentation and microstructual evolution to a group of industry attendees at a meeting hosted by EPRI. Topics include atomistic methods to determine grain boundary strength, phase-field fracture modeling to determine critical pressure at grain boundaries, and coupled phase-field-cluster dynamics to model microstructural evolution.
Overview presentation on the EPRI/INL TCF project for the CRAFT project.
Through the U.S. Department of Energy (DOE) Technology Commercialization Fund (TCF), Electric Power Research Institute (EPRI) and Idaho National Laboratory (INL) are partnering to develop an analysis tool focused on loss-of- coolant accident (LOCA) behavior of light-water reactor (LWR) fuel rods. This tool will involve a coupling of RELAP5- 3D and Bison. This report gives details of the work to be performed in this partnership. It is hoped that industry and national laboratory experts, including the Collaborative Research on Advanced Fuel Technology (CRAFT) Technical Expert Group (TEG), will provide feedback on the planned work.
Overview of work done to model UO2 HBS modeling at an upcoming DOE-CEA meeting.
This document is an American Nuclear Society (ANS) transaction for the ANS annual conference. This transaction provides an overview of the Modeling and Measurement of Axial Gas Transport Laboratory Directed Research and Development project including preliminary modeling results. The goal is to provide model for axial gas transport in the Bison Fuel Performance code to support industry's desire to achieve higher burnups in existing light water reactors. A brief overview of the experimental approach and associated modeling activities is presented.
To improve the economics of commercial nuclear energy generation, U.S. utilities are currently seeking licensing approval to operate UO2 fuel to higher burnups. One significant safety issue that must be addressed to obtain approval is the potential for fine fragmentation/pulverization of the fuel during a loss-of-coolant accident (LOCA). It has been hypothesized that pulverization is caused by the rapid increase of pressure in fission gas bubbles in the high burnup region of the fuel during a LOCA. To better understand this phenomenon, a novel phase-field model of the fission gas bubble microstructure in UO2 has been developed and implemented in Idaho National Laboratory (INL)'s Marmot application for phase-field simulation of nuclear materials. Simulations of the bubble response to steady-state and transient conditions were conducted, and the results were used to inform a mechanistic model of pulverization in BISON, INL’s fuel performance simulation code.
The desire of the nuclear industry to improve the economics of existing nuclear power plants has necessitated research into the potential of a phenomenon known as fuel fragmentation, relocation, and dispersal (FFRD). This phenomenon is possible during a loss-of-coolant accident (LOCA) at relatively high burnup. The Nuclear Energy Advanced Modeling and Simulation program has been developing simulation capabilities for FFRD and LOCA in the BISON fuel performance code for multiple years. This year, the effort has been focused on evaluating new lower length scale informed pulverization thresholds as well as updating and adding new empirical models for various phenomena. Models added or updated this year include a preliminary transient fission gas release model, new high-temperature Zircaloy creep models, a Zircaloy rupture opening area model, and a temperature-dependent emissivity during radiation from the fuel rod to the surrounding atmosphere. The models are verified through implementation tests to demonstrate code correctness after addition to BISON. The models are then assessed against a subset of the existing BISON validation suite for LOCA and FFRD cases. Two new cases, Studsvik Rods 192 and 193, have been added. The results indicate that the inclusion of a bubble pressure evolution model in the bubbles in the high-burnup structure has the largest impact compared to the 3D fracture criterion on reducing the calculated amount of pulverized fuel.
Boiling water reactors (BWRs) represent approximately one-third of the operating fleet in the United States, contributing significantly towards the global effort in reducing carbon emissions. Even though most of the operating fleet has been in operation for quite some time, continued advancements in new nuclear fuel (such as accident tolerant fuel) or operating regimes (such as power up-rates and higher burnup operation) necessitates similar advancements in modeling and simulation capabilities. Bison, a component of the Virtual Environment for Reactor Applications (VERA), is a high-fidelity fuel performance code able to explore the fuel performance of a wide variety of fuel types in one-, two-, and three-dimensions. Until recently, the code had not been used for analyses of BWRs. Modeling capabilities have been added for Gd-bearing UO{sub 2} and pure zirconium liners. New models have been added based upon the U.S. Nuclear Regulatory Commission (NRC) guide-lines for hydrogen pickup in Zircaloy-2 claddings and pellet-clad mechanical interaction (PCMI) failure during a reactivity insertion accident (RIA), known as a rod drop accident (CRDA) in BWRs. Implementing and/or improving Bison modeling capabilities extended its analytical reach to areas beyond its original intended purpose. This paper demonstrates one of these capabilities as a proof of concept. Recently developed models enable Bison to provide an alternate approach for cladding integrity determination in CRDA evaluations, which currently use bounding conservative estimates. As part of this demonstration, NRC guidance on hydrogen-pickup and PCMI failure models were utilized in this research. Even though more research is needed in establishing right inputs and process in this area, this paper demonstrates Bison's ability to determine cladding integrity in a CRDA evaluation. This first of a kind demonstration is a proof of concept in this area, which could potentially be extended to a number of other areas where a more accurate cladding integrity determination would be needed. (authors)
Summary to be presented at EPRI-DOE workshop on high burnup and accident tolerant fuel
To improve the economics of commercial nuclear energy generation, U.S. utilities are currently seeking licensing approval to operate UO2 fuel to higher burnups. One significant safety issue that must be addressed to obtain approval is the potential for fine fragmentation/pulverization of the fuel during a loss-of-coolant accident (LOCA). The cause of pulverization has been hypothesized to be the rapid increase of pressure in fission gas bubbles in the high burnup region of the fuel during a LOCA. To better understand this phenomenon, a novel phase-field model of the fission gas bubble microstructure in UO2 has been developed and implemented in Idaho National Laboratory (INL)'s Marmot application for phase-field simulation of nuclear materials. Simulations of the bubble response to steady-state and transient conditions were conducted. Simulation results were used to inform a mechanistic model of pulverization in BISON, INL’s fuel performance simulation code.
Slides for presentation at AFC review meeting 12/14/21
This short presentation summarizes the NEAMS/AFC collaboration on assessment activities for high burnup applications.
The U.S. Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS)program aims to develop predictive capabilities using computational methods for the analysis and design of advanced reactor and fuel cycle systems. This program has been supporting the development of BISON, a high-fidelity and high-resolution fuel performance tool at the engineering scale. This document continues analysis and refinement of capabilities added to BISON early this calendar year in regards to the incorporation of capabilities applicable to extended burnups in response to industry interest. Details are provided on high burnup thermal conductivity models, a refitting of the high-burnup structure (HBS) porosity formation model to include additional data, the coupling of the HBS volume fraction model to thermal conductivity and fine fragmentation models, and validation activities. The IFA-650.4 and IFA-650.9 loss of coolant accident (LOCA) analyses are revisited with the latest developments in this report. A new validation case, IFA-650.14 has also been added to the BISON test suite.
Until this year the BISON fuel performance code has been developed primarily for pressurized water reactor (PWR), accident tolerant fuel (ATF), and advanced reactor (e.g., tri-structural isotropic (TRISO), metallic) analyses. The main focus of this work is to develop and document required material models that would aid predicting cladding failure with a specific hydride distribution to be investigated for boiling water reactor (BWR) applications in the next fiscal year. In terms of materials, the primary differences between a BWR and PWR is the use of gadolinia doping of the UO 2 fuel, the use of Zircaloy-2 for the cladding, and the addition of a liner on the inner surface of the cladding for improved pellet-clad mechanical interaction (PCMI)performance. The liner is typically made of pure zirconium or a lower tin content zirconium alloy (e.g. Zr-0.3%Sn). This work details the development and documentation of material and behavioral models for BWR analysis such as the addition of material and behavior models for gadolinia doped UO 2 , pure zirconium, Zr-0.3%Sn, and Zircaloy-2 as well as the ease-of-use additions to allow internal meshing capabilities to include liners. Another important aspect affecting cladding performance is hydrogen diffusion and hydride precipitation in the cladding. A model was added previously for non-lined, homogeneous claddings. In this work, instructions are provided on how to apply the model to BWR liner cladding. Representative experimental values are provided for the hydrogen diffusion parameters and precipitation-dissolution kinetics for typical liner materials of interest.