Search NASA⌕ Search

Engineering topics

Gambucci, B. J.

Publications and source records attributed to Gambucci, B. J..

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Unpowered Aerodynamic Characteristics of a 15-Percent Scale Model of a Twin-Engine Commuter Aircraft

An experimental investigation was conducted in the Ames 12-Foot Pressure Wind Tunnel to determine the unpowered aerodynamic characteristics of a 15-percent-scale model of a twin-engine commuter aircraft. Model longitudinal aerodynamic characteristics were examined at discrete flap deflections for various angle-of-attack and wind-tunnel-velocity ranges with the empennage on and off. Data are presented for the basic model configuration consisting of the fuselage, wing, basic wing leading edge, double slotted flaps, midengine nacelles, and empennage. Other configurations tested include a particle-span drooped leading edge (dropped outboard of the engine nacelles), a full-span drooped leading edge, low- and high-mounted engine nacelles, and a single-slotted flap. An evaluation was made of the model mounting system by comparing data obtained with the model mounted conventionally on the wind-tunnel model-support struts and the model inverted.

Morgan, D. G.↗
NASA NTRS1978

Effect of high lift flap systems on the conceptual design of a 1985 short-haul commercial STOL tilt rotor transport

The performances of a derivative concept of a 1985 STOL tilt rotor transport, and of a second concept having a complex mechanical flap system similar to a short field B737 aircraft were compared for a 370 kilometer (200 nautical mile) short haul mission. The flap system of the latter allowed lift to be shifted from the rotor system to the wing, permitting a 26 percent reduction in dynamic component weight, while also permitting the use of a smaller wing. The wing and disc loading of this concept were 5746 (120 psf) and 1915 (40 psf) newtons per square meter, respectively, while the wing and disc loading of the derivative concept were 4788 (100 psf) and 1197 (25 psf) newtons per square meter, respectively. The high lift wing tilt rotor showed slightly improved fuel usage over its entire operating range and about 6 to 8 percent improvement in direct operating costs, resulting from its improved cruise efficiency and reduced weight. Other advantages include improved reliability with potentially reduced maintenance and better riding quality.

Shovlin, M. D.↗
NASA NTRS1976

Wind-tunnel investigation of a large-scale model of a lift-cruise fan V/STOL aircraft with extended lift-cruise nacelles

The aerodynamic characteristics of a large-scale model of a lift/cruise fan V/STOL aircraft were determined. The model was equipped with three fans, one mounted in the forward section of the fuselage in a lift mode, and two mounted on top of the wing adjacent to the fuselage in a lift/cruise mode. The data that were obtained include longitudinal and lateral-directional characteristics of the model, with the horizontal tail on and off, for both the powered-lift and cruise configurations. Lateral-directional characteristics were obtained with the horizontal and vertical tail sections removed. Powered-lift data were obtained at several wind-tunnel velocities and at several lift-cruise fan thrust vector angles by varying the position of the hooded deflectors from 0 deg (the cruise condition) to 90 deg.

Gambucci, B. J.↗
NASA NTRS1976

Wind tunnel investigation of a large-scale model of a lift/cruise fan V/STOL aircraft

An investigation was conducted in the Ames 40- by 80-Foot wind tunnel to determine the aerodynamic characteristics of a large scale model of a lift/cruise fan V/STOL aircraft. The model was equipped with three fans, one mounted in the forward section of the fuselage in a lift mode, and two mounted on top of the wing adjacent to the fuselage in a lift/cruise mode. The data that were obtained include longitudinal and lateral-directional characteristics of the model, with the horizontal tail on and off, for both the Powered lift and cruise configurations. Powered lift data were obtained at several wind tunnel velocities and at several lift/cruise fan thrust vector angles by varying the position of the hooded deflectors from 0 deg. (the cruise condition) to 90 deg.

Gambucci, B. J.↗
NASA NTRS1972

An analysis of the takeoff and landing performance of a jet-powered STOL augmentor wing design

A preliminary study of the takeoff and landing performance characteristics of a swept wing airplane with augmented jet flap, designed for STOL operation and low noise is presented. The study is based on aerodynamic data from wind tunnel tests of a large-scale swept augmentor wing model, scaled up to a 48,000 pound airplane. Engine characteristics are based on a turbo fan with a fan pressure ratio of 2.5 delivering the major portion of the thrust to the augmentor flap. A description of the overall airplane configuration, the propulsion system, and the use of the aerodynamics is presented. To assess the STOL performance of the airplane, takeoff and landing distances and flight path capabilities were computed at various flap deflections and thrust levels. After evaluating these results in terms of desired STOL performance with required margins, basic takeoff and landing configurations were chosen.

Post, S. E.↗
NASA NTRS1972

Initial rotation-loading and low speed flutter test results for a straight wing version of the space shuttle vehicle

For three straight semispan model space shuttle wings, the maximum total load during rapid rotation from 66 deg to 0 deg angle of attack, at Mach numbers from 0.28 to 0.60, was essentially no higher than that measured for buffet. During slow rotation over the same angle range, there was no visible flutter. For one of the wings, however, unstable aerodynamic damping was established at two fixed angles of attack.

Warner, R. W.↗