Search NASA⌕ Search

Engineering topics

Gandha, Kinjal

Publications and source records attributed to Gandha, Kinjal.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Recycling of additively printed anisotropic Nd-Fe-B bonded magnets

A high potential cost-effective and environmentally friendly method has been applied for recycling anisotropic Nd-Fe-B bonded magnets. Waste additively printed Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) Nd-Fe-B anisotropic bonded magnet was pulverized into composite powder containing Nd-Fe-B particles and nylon binder through cryomilling at a liquid nitrogen temperature (~77 K) under Ar inert atmosphere. Then, the cryomilled composite powder was warm compacted into a bonded magnet. Further, the magnetic particles were aligned during post-compaction annealing under a magnetic field of 30 kOe. The recycled bonded magnets have a higher density (3% enhancement), but slightly inferior magnetic properties compared to the original magnets, i.e., the magnetic remanence, coercivity and maximum energy product are reduced by 2%, 3% and 8%, respectively. The scanning electron microscopy revealed that some HDDR Nd-Fe-B powder crumbled into fine particles during cryomilling. Powder X-ray diffraction showed a small amount of Nd-oxide impurity in the cryomilled powder. The slightly deteriorated magnetic properties are ascribed to the oxidation of Nd-Fe-B particles due to formation of fresh fracture surface during cryomilling. The approach enables the direct reuse of end-of-life bonded magnets in an economical and environmentally friendly way.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Post-sintering Annealing on (NdLa)-(FeCo)-B Magnets

A common limitation of La substitutions into (Nd, La) 2 Fe 14 B magnets is the reduction of the anisotropy field (H a ), which decreases magnet coercivity (H cj ). In this study, adding a small amount of Pr-Cu to a La-containing neo magnet may modify the grain boundary (GB), which can help recover a fraction of the degraded H cj . An optimal GB modification requires a carefully designed post-sinter heat treatment, which is the focus of this work on characterizing the effects of multi-step post-sintering annealing on the evolutions of microstructure and magnetic properties. We find that Nd and Cu concentrations at GBs and triple junctions (TJs) increase when the annealing temperatures are lowered. Annealing temperatures of 580°C and 480°C (near rare-earth-rich eutectic temperatures) enabled the development of a thick and continuous GB phase, which helps to magnetically decouple the grains, and, thus, enhance H cj . For the alloy with 25% Nd replaced by La, and with the addition of 7.5 wt.% of Pr 68 Cu 32 as GB modifier, the optimized multi-step post-sinter annealing improved the H cj from 4.8 kOe to 9 kOe.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of magnetic field annealing on the hard magnetic properties of milled Nd-Fe-B powders

In this study, we report the effect of magnetic field annealing (MA) in relieving the stress induced during the milling of Nd-Fe-B sintered magnets. The effect of MA processing parameters and particle size on the magnetic properties were investigated. Based on the results, magnetic field annealing is more effective in improving the magnetic properties of larger size particles, compared to finer particles. Our computational study on the role of particle surface defects in bi-modal particle distribution agrees with results obtained experimentally. In conclusion, magnetic field annealed powder has been successfully used to develop 4.6 g.cm -3 density bonded magnets with 75 vol% of magnetic powder and polyamide 12 (nylon 12) polymer binder resulting in 11.3 MGOe energy product.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermal stability of anisotropic bonded magnets prepared by additive manufacturing

Abstract In this research, anisotropic NdFeB + SmFeN hybrid and NdFeB bonded magnets are additively printed in a polyphenylene sulfide (PPS) polymer binder. Printed NdFeB + SmFeN PPS bonded magnets displayed excellent magnetic properties ( B r [remanence] = 6.9 kG [0.69 T], H cj [coercivity] = 8.3 kOe [660 kA/m], and BH max [energy product] = 9.9 MGOe [79 kJ/m 3 ]) with superior corrosion resistance and thermal stability. The anisotropic NdFeB bonded magnet shows a high coercivity of 14.6 kOe (1162 kA/m) with a BH max of 8.7 MGOe (69 kJ/m 3 ). The coercivity and remanence temperature coefficients for NdFeB + SmFeN hybrid bonded magnets are −0.10%/K and −0.46%/K, and for NdFeB bonded magnets are −0.14%/K and −0.53%/K in the range of 300–400 K, indicating that the hybrid bonded magnets are thermally stable. The average flux aging loss for hybrid magnets was also determined to be very stable over 2000 h at 448 K (175°C) in air with 2.04% compared to that of NdFeB magnets with 3.62%.

thermal stability↗
DOE OSTI2022

Microstructural evolutions, phase transformations and hard magnetic properties in polycrystalline Ce–Co–Fe–Cu alloys

This work focuses on systematic studies of Ce–Co based 1:5 permanent magnet alloys of CeCo 4.4-x Fe x Cu 0.6 and CeCo 3.9-x Fe x Cu 1.2 (x = 0, 0.3, 0.6, 0.9, 1.2, 1.8) by varying Co:Fe. The overarching aim of this manuscript is to elucidate the hard-magnetic properties through a better understanding of phase formation by the structural, microstructural, and magnetic properties in these materials. Improved mutual solubility of Fe in the 1:5 phase has been observed with an extended homogeneity range by Cu substitution. For both composition series, Fe contents of x ≤ 0.6 show a homogeneous microstructure with a single 1:5 phase and good magnetic properties. The composition region 0.6 < x ≤ 0.9 appears to be near the boundary of solubility and evolution of other phases. At x = 1.8, it is found that the homogeneous 1:5 phase and magnetic hardness deteriorated due to the evolution of secondary phases such as 2:17, 2:7, and Fe–Co. Furthermore, the addition of Fe improved both the magnetization and Curie temperature via increased effective exchange interactions, while an increase in Cu content enhanced coercivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Pressure dependent magnetic properties on bulk CrBr 3 single crystals

The van der Waals class of materials offer an approach to two-dimensional magnetism as their spin fluctuations can be tuned upon exfoliation of layers. Moreover, it has recently been shown that spin-lattice coupling and long-range magnetic ordering can be modified with pressure in van der Waals materials. In this work, the magnetic properties of quasi two-dimensional CrBr 3 are reported applying hydrostatic pressure. The application of pressure up to 0.844 GPa shows a 1.77% decrease in saturation magnetization with a decrease in the Curie temperature from 33.05 to 30.41 K. Density functional theory calculations with pressure up to 1 GPa show a reduction in volume and interplanar distance as pressure increases. To further understand the magnetic properties with applied pressure, the magnetocrystalline anisotropy energy (MAE) and exchange coupling parameter (J) are calculated. There is small decrease in MAE and the first nearest neighbor interaction (J 1 ) (U = 2.7 eV and J = 0.7 eV) is increasing with respect to increasing pressure. Overall, CrBr 3 displays ferromagnetic interlayer coupling and the calculated exchange coupling and MAE parameters match well with the observations from the experimental work.

36 MATERIALS SCIENCE↗