Engineering topics

Gao, J. M.

Publications and source records attributed to Gao, J. M..

5 records

DOE OSTI2024

Recent advance progress of HL-3 experiments

Since the first plasma realized in 2020, a series of key systems on HL-3 (known as HL-2M before) tokamak have been equipped/upgraded, including in-vessel components (the first wall, lower divertor, and toroidal cryogenic/water-cooling/baking/glow discharge systems, etc.), auxiliary heating system of 11 MW, and 28 diagnostic systems (to measure the plasma density, electron temperature, radiation, magnetic field, etc.). Magnet field systems were commissioned firstly for divertor plasma discharges. During the 2nd experimental campaign of HL-3 tokamak, several great progresses have been achieved. Firstly, the successful operation with plasma current larger than 1 MA was achieved under a divertor configuration. Secondly, the advanced divertor concept with two distinct snowflake configurations was realized. It is found that the distribution of ion saturation current and heat flux on bottom plate becomes wide due to magnetic surface expansion, demonstrating the advantage of such configuration in the heat flux mitigation. In addition, using the combination of NBI, ECRH and LHCD, the standard sawtoothing high confinement mode of megampere plasma was firstly accessed on the HL-3. The successful commissioning of HL-3 is beneficial for the initial operation of ITER.

1 MA plasma↗

DOE OSTI2022

Toroidal modeling of 3D perturbations generated by current filaments in scrape-off layer in tokamak with biased divertor targets

The divertor biasing technique offers a promising alternative to control the edge localized mode (ELM) as well as the divertor heat load in tokamaks, as compared to the resonant magnetic perturbation (RMP) generated by magnetic coils. The linear resistive MHD code MARS-F (Liu et al 2000 Phys. Plasmas 7 3681) is employed to study the plasma response to the n = 2 (n is the toroidal mode number) field perturbation in HL-2A, produced by the divertor biasing current filaments flowing in the scrape-off layer region. The response field due to biasing currents is compared with the RMP field utilized for ELM control in HL-2A. The strength of the radial resonant field perturbation, produced by the biasing currents of 100 A level, is found to be comparable with RMP generated by several kA of ELM control coil currents for the reference plasma. The plasma normal displacement near the X-point and the associated neoclassical toroidal viscosity torque are also computed to be similar between these two techniques. The modeling results thus strongly suggest that the biasing technique can be applied to control ELMs. Moreover, the biasing currents produce field perturbations, including the plasma response, that are localized more near the plasma edge (compared to the RMP counterpart), thus reducing the chance of mode locking associated with core perturbations. Particle orbit tracing also reveals that the biasing current produced magnetic perturbation tends to widen the heat deposition region and induce the strike point splitting of the ion saturation flow on the outer divertor surface, consistent with experimental observations in HL-2A. These toroidal modeling results confirm the possibility of ELM control and plasma exhaust solution by the divertor biasing technique.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Electrode biasing maintains the edge shear layer at high density in the J-TEXT tokamak

Collapse of the edge flow shear as the line-averaged density approaches the Greenwald density limit has been observed as a precursor to the enhanced edge particle flux characteristic of proximity to the density limit regime. Here, we report the use of a biased electrode to sustain the edge shear layer in high density discharges, in which the shear layer would otherwise collapse. A stable increase in line-averaged density is observed along with a strong increase in edge density. These experiments were carried out on the J-TEXT tokamak. The Reynolds stress at the edge is enhanced, and the zonal flow sustained, while density perturbation levels, the flux of turbulence internal energy (i.e., turbulence spreading), and particle and heat flux all decrease significantly. Electron adiabaticity increases, and bias voltage modulation experiments show that an increase in the edge shear leads the increase in adiabaticity. Furthermore, these results suggest that external edge E × B flow shear drive may be of interest for sustaining edge plasma states at high density, and support the hypothesis that collapse of the edge shear layer triggers the onset of the strong transport and turbulence characteristic of the density limit regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Enhanced particle transport events approaching the density limit of the J-TEXT tokamak

Enhanced particle transport events are discovered and analyzed as the density limit of the J-TEXT tokamak is approached. Edge shear layer collapse is observed and the ratio of Reynolds power to turbulence production decreases. Simultaneously, the divergence of turbulence internal energy flux (i.e. turbulence spreading) increases, indicating that shear layer collapse triggers an outward spreading event. Studies of correlations show that the enhanced particle transport events are quasi-coherent, and manifested primarily in density fluctuations which exhibit positive skewness. Furthermore, electron adiabaticity emerges as the critical parameter which signals transport event onset. For α < 0.35 as density approaches the Greenwald density, both turbulence spreading and density fluctuations rise rapidly. Taken together, these results elucidate the connections between edge shear layer, density fluctuations, particle transport events, turbulence spreading and plasma edge cooling as the density limit is approached.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Simulations of heat fluxes in an ELMy H-mode discharge on HL-2A

In order to study the distribution and evolution of the transient heat flux on HL-2A during edge-localized-mode (ELM) bursts, the BOUT++ electromagnetic six-field two-fluid model is used to simulate the pedestal collapse under the lower single-null divertor geometry. The equilibrium profiles of HL-2A ELMy H-mode discharge No. 24 953 are adopted as the initial condition in the original case. In this instance, linear analysis shows that the resistive ballooning mode (RBM) and drift-Alfven wave are unstable to this equilibrium, and RBM is the dominant instability. The evolutions of the radial heat fluxes at the outer mid-plane and heat fluxes to the inner and outer targets during the ELM event are presented. Six more equilibria are constructed based on the original case to find out the influence of the pedestal profiles on the peak electron heat flux. The results indicate that the heat flux increases with temperature and/or density, and the theoretical analysis and simulation results consistently show that the heat flux q ∥e is proportional to n e0,SEP $T^{\frac32}_{e0,SEP}$.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗