Search NASA⌕ Search

Engineering topics

Gao, Jian

Publications and source records attributed to Gao, Jian.

At least 19 records

Progressive evolutions of non-fused ring electron acceptors toward efficient organic solar cells with improved photocurrent and reduced energy loss

Resolving competitive counterbalance between high external quantum efficiency (EQE) response and low energy loss is critical for achieving efficient organic solar cells (OSCs), including those based on low-cost non-fused-ring electron acceptor (NFREA). In this work, we performed a comparable study by utilizing four NFREAs with progressive evolutions in molecular structures, energetic levels, spectral coverages, crystallinity, etc, to pair with polymer donor J52. By regulating the terminal and side chains of NFREAs, the enhanced intramolecular charge transfer (ICT) effect allows O-PC-EH possessing the broader spectral coverage for higher photocurrent, the reduced energetic offset enables O-PC-EH-based device owning higher luminescence property for lower energy loss, the strengthened crystallinity endows O-PC-EH-based blend better charge transport property for less charge recombination. With those comprehensive managements from molecule to blend properties, the J52:O-PC-EH-based OSCs achieved the best efficiency of 14.4% (certified: 14.1%) with benefits in all the three device parameters. Here, this work reveals the importance of fine-tuning molecular structures of NFREAs according to paired polymer donor for maximizing the device performances.

14 SOLAR ENERGY↗

An indirect approach to optimize the reaction rates of thermal NO formation for diesel engines

With stringent emission regulations, it has become more important for modern diesel engine manufacturers to accurately predict engine-out nitrogen oxide (NO x ) emissions across a wide range of operating conditions. Thermal NO is the major source of engine-out NO x in modern diesel engines. For thermal NO formation, several earlier studies have recommended the forward and reverse reaction rate coefficients of the rate-limiting reaction (O + N 2 ⇌ NO + N). However, due to deficiencies in sub-models and inadequacies of reduced chemical mechanisms to represent diesel combustion, these recommended values more often than not need to be adjusted in reduced order combustion models to accurately predict engine-out NO x . Hence, in this work a systematic and computationally efficient approach has been proposed to streamline the process of determining the optimum reaction rate coefficients. Here, to develop the optimization approach, four different production diesel engines with different operating conditions in terms of speed, load, and exhaust-gas recirculation have been considered. Numerical simulations have been performed using a detailed zero-dimensional velocity-composition-frequency transported probability density function (0D-VCF-tPDF) model that uses hundreds of notional particles to capture in-cylinder stratification. Four different combinations of hydrocarbon and NO x chemical mechanisms were used to represent chemistry. It was found that for the rate-limiting reaction, the pre-exponent factors (A f1 , A r1 ) and activation energies (E A,f1 , E A,r1 ) of the forward and reverse reaction rates follow a linear band in A f1 - E A,f1 and A r1 - E A,r1 space where predicted engine-out NO x match the measured values closely. By encompassing such bands from different engines and considering constraints on activation energies, a reduced search domain of pre-exponent factors and activation energies was constructed that is expected to be applicable to any diesel engine. Eventually, computationally efficient three-line and one-line search approaches were proposed to determine the optimum values of the pre-exponent factors and activation energies that led to a minimum error between measured and predicted engine-out NO x . Finally, these three-line and one-line NO x optimization approaches were applied to a fifth production diesel engine for which the 0D-VCF-tPDF model showed a very good predictive performance in terms of predicting peak pressure, 50% burn rate, and engine-out NO x when compared to measured and 3D-CFD values.

33 ADVANCED PROPULSION SYSTEMS↗

Modeling Needs for High Power Target

The next generation of high power targets will use more complex geometries, novel materials, and new concepts (like flowing granular materials); however, the current numerical approaches will not be sufficient to converge towards a reliable target design that satisfies the physical requirements. We will discuss what can be improved in the next 10 years in target modeling to support high power (MW class) targets.

43 PARTICLE ACCELERATORS↗

Dynamic fracture of glass fiber-reinforced ductile polymer matrix composites and loading rate effect

Here, the dynamic fracture of S-2 glass fiber-reinforced polymer matrix composites (FRPMCs) was investigated in this study. The matrix ductility was improved by a recently developed network topology modification technique via mixing partially reacted substructures (mPRS). The composite material was manufactured and characterized by micro-CT scanning and scanning electron microscopy (SEM). Dynamic single-edge notched bending (d-SENB) experiments were performed on the composites by using a modified split-Hopkinson pressure bar. Each specimen’s fracture process was visualized by ultrafast X-ray imaging. Such in-situ radiography enabled identifying the damage initiation below 50-micron scale and inspecting its propagation through the internal structures of opaque composites, thereby accurately quantifying the composites’ mechanical properties. Furthermore, the identical d-SENB experiments were designed and the digital image correlation (DIC) was employed to monitor the stress wave propagation on the composite specimens. The force and deflection measurements were modified and correlated to the physical damage processes. Besides, quasi-static SENB experiments were conducted to identify the loading rate effects on the composites’ fracture behaviors. The force and deflection history, bending stiffness, energy dissipation, and fracture toughness at different loading rates were quantified and compared. Finally, post-fracture analysis by micro-CT scanning and SEM provided physical observations on the variation of the fracture morphology by different loading rates.

42 ENGINEERING↗

Fabrication of mass spectrometry surface

Disclosed herein are compositions for ionizing a target and methods for making the compositions. In some embodiments, the compositions can include a structured substrate having a plurality of upright surface features, for example, microscale or nanoscale pillars, in contact with an initiator. Also disclosed herein are methods for ionizing targets.

Gao, Jian↗

Transverse impact by RCCs on S-glass and Kevlar® FRC strips

This study aims to isolate interactions between plies and tows and reveal fundamental physics involved in transverse impact on fiber-reinforced composite (FRC) structures. Composite strips were sectioned from large panels and characterized by optical photography, three-dimensional synchrotron X-ray computed tomography, and scanning electron microscopy (SEM). Each strip was impacted perpendicularly by a right circular cylinder (RCC) projectile at a velocity ranging from ~ 150 to 600 m/s. The global strip behavior, as well as localized deformation and failure of the strip near the projectile corner, were both captured by high-speed optical imaging. S-Glass FRC strips were observed to fail in tension ahead of the RCC projectiles’ flat surfaces while Kevlar® FRC strips fractured at the projectile corners. The concept of critical velocity region previously used for impact on yarns was introduced to define different failure modes of each composite strip type. The strip damage extent was found to increase with the impact velocity and reach the maximum at the upper limit of the critical velocity region. Above the critical velocity region, the damage extent decreased with impact velocity. Wave propagations and load histories in the composite strips during impact were quantified and compared with Smith’s theory. Finally, critical velocities of single fibers, yarns, and composite strips and ballistic limits of single-ply and multi-ply composite panels were compared to provide insight into the design of impact-resistant fabrics and composites.

42 ENGINEERING↗

Real-time damage characterization for GFRCs using high-speed synchrotron X-ray phase contrast imaging

Here, we report the application of high-speed synchrotron X-ray phase contrast imaging (PCI) in real-time damage characterization for glass fiber reinforced composites (GFRCs) subjected to dynamic loading. Dynamic single-edge notched bending (DSENB) experiments on pre-notched S-2 GFRCs were performed on a modified Kolsky compression bar. During loading, the synchrotron X-ray beam penetrated through the composite specimen from the side to detect damage evolution inside the material. Entire dynamic events were recorded by a high-speed camera as image sequences.0° and 90° unidirectional and cross-ply composites were investigated. An optical imaging technique was also employed to capture similar dynamic events in comparison with the radiographic imaging. It is demonstrated that high-speed X-ray PCI had sufficient phase contrast to characterize a crack initiation at a 20-μm spatial resolution within 920 ns and track the crack geometry during propagation, thereby providing reliable data to quantify the dynamic damage resistance of GFRCs. Furthermore, being capable of recognizing microscopic damage-related features at a sub-10-μm resolution, high-speed X-ray PCI provided fundamental material failure mechanisms to reveal the essential of macroscale structural failure of composites. It can also track the damage evolution inside and between individual plies of laminated composites. However, current high-speed X-ray PCI technique only supports in-situ observation and the high timing and spatial resolutions are limited within a field of view of ~2.5 mm in square, preventing its application in the three-dimensional and larger-area damage detection for GFRC structures.

42 ENGINEERING↗

A method for characterization of multiple dynamic constitutive parameters of FRCs

We propose a method to measure multiple dynamic material constitutive parameters of unidirectional fiber reinforced composites (FRCs) in a single experiment. Dynamic short-beam shear (DSBS) experiments were performed on a modified Kolsky compression bar, with integration of high-speed imaging and digital image correlation (DIC). The unidirectional FRCs investigated were S-2 glass fiber reinforced matrix of TGDDM-Jeffamine® D230 with monoamine functionalized partially reacted substructures (mPRS) and commercially available SC-15. Analytical solutions of normal and shear strains of a composite beam were derived based on Timoshenko beam theory, assuming material to be transversely isotropic and have different moduli in tension and compression in each principle material orientation. Tensile and compressive moduli were inversely computed through monitoring normal strain slope when specimen was constantly loaded at a speed of ~7.3 m/s within a small deflection. Non-linear shear stress-strain behavior of the composite was described via Ramberg–Osgood equation. Finite element (FE) analysis was conducted in ABAQUS, simultaneously defining via user subroutine UMAT the transverse isotropy of material, bi-modulus constitutive model, and non-linear shear stress-strain relation. The method proposed in this work was validated by comparing strain distributions computed by FE model and DIC measurements. Comparing with traditional dynamic tensile, compressive, and shear experiments on FRCs, this method significantly simplifies the specimen preparation and design of complicated gripping fixtures for multiple experiments. Here, systematic errors resulting from variations of specimen geometry and dimension, loading direction, and instrumentation are reduced, thereby providing compatible data for numerical studies on impact behavior of composites.

36 MATERIALS SCIENCE↗

Ecosystem for determining plant-microbe interactions

Disclosed herein are systems, methods, and devices for determining plant-microbe interactions. In some embodiments, the device comprises: a root chamber configured to allow a root of a plant to grow, wherein the root chamber is connected with: an inlet channel for introducing a medium into the root chamber, an outlet channel for collecting plant exudates and metabolites, and a plant reservoir for the plant shoot of the plant to grow.

59 BASIC BIOLOGICAL SCIENCES↗

Persistent Heavy Winter Nitrate Pollution Driven by Increased Photochemical Oxidants in Northern China

Nitrate is an increasingly important component of fine particulate matter (PM2.5) during winter in northern China. Past emission control has been ineffective in reducing winter nitrate. Here, we use extensive observations and a model with state-of-theart nitrogen chemistry to identify the key factors that control the nitrate formation in the heavily polluted North China Plain (NCP). In contrast to the previous view of weak winter photochemistry, we show that the O3 and OH productions are sufficiently high in winter to facilitate fast gas-phase and heterogeneous conversion of NOX to nitrate over the NCP. Increasing O3 and OH productions from higher precursor levels and fast ROX cycling accelerate the nitrate generation during heavy pollution. We find that the 31.8% reduction of NOX emissions from 2010 to 2017 in the NCP lowers surface nitrate by only 0.2% and even increases nitrate in some polluted areas. This is mainly due to the increase of O3 and OH (by~30%), which has subsequently increased the conversion efficiency of NOX to HNO3 (by 38.7%). Future control strategies for the winter haze should also aim to lower photochemical oxidants, via larger and synchronized NOX and VOCs emissions reduction, to overcome the effects of nonlinear photochemistry and aerosol chemical feedback.

Fu, Xiao↗

Probing the surface of promoted CuO-Cr 2 O 3 -Fe 2 O 3 catalysts during CO 2 activation

The influence of basic oxide promoters on copper-chromium-iron oxide catalysts was investigated to determine the nature of surface oxygen species and structure-activity relationship for the reverse water-gas shift reaction. The catalysts were characterized with in situ XRD, in situ Raman, in situ XPS, in situ HS-LEIS and H 2 -TPR. Two surface oxygen sites with different reduction characteristics were found to be present. The overall CO 2 activation rate was found to correlate with both the number and reducibility of the more active oxygen species that were likely associated with the Cu-FeO x interfacial regions for enhanced hydrogen spillover. While addition of K 2 O somewhat preserved the interfacial regions and facilitated the reduction kinetics of surface oxygen, both Na 2 O and CaO significantly suppressed the availability of metallic Cu as well as the Cu-FeO x interfaces, leading to decreased reactivity. These findings provide a direction to promote the copper-iron catalysts by creating more metal-metal oxide interfacial sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Detection of analytes using porous mass spectrometry surface

The disclosure herein includes compositions and methods for ionizing targets and methods for making the compositions. In some embodiments, the compositions can include a porous substrate that has been etched for a desired average pore size, a desired porosity, or both for detection of one or more targets of interest. Also disclosed herein are methods for using the composition to ionize targets.

36 MATERIALS SCIENCE↗