Search NASA⌕ Search

Engineering topics

Gardiner, Arthur W

Publications and source records attributed to Gardiner, Arthur W.

Preliminary Flight Tests of the N.A.C.A. Roots Type Aircraft Engine Supercharger

An investigation of the suitability of the N.A.C.A. Roots type aircraft engine supercharger to flight-operating conditions, as determined the effects of the use of the supercharger upon engine operation and airplane performance, is described in this report. Attention was concentrated on the operation of the engine-supercharger unit and on the improvement of climbing ability; some information concerning high speeds at altitude was obtained. The supercharger was found to be satisfactory under flight-operating conditions. Although two failures occurred during the tests, the causes of both were minor and have been eliminated. Careful examination of the engines revealed no detrimental effects which could be attributed to supercharging. Marked improvements in climbing ability and high speeds at altitude were effected. It was also found that the load which could be carried to a given moderate or high altitude in a fixed time was considerably augmented. A slight sacrifice of low-altitude performance was necessitated, however, by the use of a fixed-pitch propeller. From a consideration of the very satisfactory flight performance of the Roots supercharger and of its inherent advantages, it is concluded that this type is particularly attractive for use in certain classes of commercial airplanes and in a number of military types.

Gardiner, Arthur W↗

The relative performance obtained with several methods of control of an overcompressed engine using gasoline

This report presents some results obtained during an investigation to determine the relative characteristics for several methods of control of an overcompressed engine using gasoline and operating under sea-level conditions. For this work, a special single cylinder test engine, 5-inch bore by 7-inch stroke, and designed for ready adjustment of compression ratio, valve timing and valve lift while running, was used. This engine has been fully described in NACA-TR-250. Tests were made at an engine speed of 1,400 R. P. M. for compression ratios ranging from 4.0 to 7.6. The air-fuel ratios were on the rich side of the chemically correct mixture and were approximately those giving maximum power. When using plain domestic gasoline, detonation was controlled to a constant, predetermined amount (audible), such as would be permissible for continuous operation, by (a) throttling the carburetor, (b) maintaining full throttle but greatly retarding the ignition, and (c) varying the timing of the inlet valve to reduce the effective compression ratio. From the results of the tests, it may be concluded that method (b) gives the best all-round performance and, being easily employed in service, appears to be the most practicable method for controlling an overcompressed engine using gasoline at low altitudes.

Gardiner, Arthur W↗

The comparative performance of an aviation engine at normal and high inlet air temperatures

This report presents some results obtained during an investigation to determine the effect of high inlet air temperature on the performance of a Liberty 12 aviation engine. The purpose of this investigation was to ascertain, for normal service carburetor adjustments and a fixed ignition advance, the relation between power and temperature for the range of carburetor air temperatures that may be encountered when supercharging to sea level pressure at altitudes of over 20,000 feet and without intercooling when using plain aviation gasoline and mixtures of benzol and gasoline. The results show that for the conditions of test, both the brake and indicated power decrease with increase in air temperature at a faster rate than given by the theoretical assumption that power varies inversely as the square root of the absolute temperature. On a brake basis, the order of the difference in power for a temperature difference of 120 degrees F. Is 3 to 5 per cent. The observed relation between power and temperature when using the 30-70 blend was found to be linear. But, although these differences are noted, the above theoretical assumption may be considered as generally applicable except where greater precision over a wide range of temperatures is desired, in which case it appears necessary to test the particular engine under the given conditions. (author)

Gardiner, Arthur W↗

A Preliminary Study of Fuel Injection and Compression Ignition as Applied to an Aircraft Engine Cylinder

This report summarizes some results obtained with a single cylinder test engine at the Langley Field Laboratory during a preliminary investigation of the problem of applying fuel injection and compression ignition to aircraft engines. For this work a standard Liberty Engine cylinder was fitted with a high compression, 11.4 : 1 compression ratio, piston, and equipped with an airless injection system, including a primary fuel pump, an injection pump, and an automatic injection valve. The results obtained during this investigation have indicated the possibility of applying airless injection and compression ignition to a cylinder of this size, 8-inch bore by 7-inch stroke, when operating at engine speeds as high as 1,850 R. P. M. A minimum specific fuel consumption with diesel engine fuel oil of 0.30 pound per I. HP. Hour was obtained when developing about 16 B. HP. At 1,730 R. P. M.

Gardiner, Arthur W↗

Increasing the compression pressure in an engine by using a long intake pipe

During some tests of a one-cylinder engine, using gas oil (diesel engine oil, specific gravity 0.86 at 60 F) with solid injection and compression ignition, it was found to be necessary to increase either the jacket water temperature or the compression pressure in order to start the engine. It was found that a sufficient increase in compression pressure could be obtained simply by attaching a long pipe to the inlet flange of the cylinder. However, since no data were available giving the values of the increase in compression pressure that might be expected from such a step-up, an investigation was made covering some engine speeds between 500 r.p.m. and 1800 r.p.m. The data obtained are included here in the form of curves. Although this data is not strictly applicable to another engine, it should give indications of what might be expected with such a set-up on an engine operating at similar speeds. The engine used was a single cylinder Liberty, 5-inch bore and 7-inch stroke, having standard cylinder, cams, valves, and valve timing and operating on a four-stroke cycle.

Mathews, Robertson↗