Search NASA⌕ Search

Engineering topics

Garlea, Elena

Publications and source records attributed to Garlea, Elena.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Assessing the influence of microstructure on uranium hydride size distributions via small angle neutron scattering

Here, the effect of microstructure on the internal hydriding behavior of both cast (1 mm grain size) and rolled (25 μm grain size) uranium containing hydrogen concentrations between 0 and 1.8 wppm were evaluated via small angle neutron scattering (SANS). Increasing hydrogen content up to 1.8 wppm in the cast uranium only weakly affected the average uranium hydride (UH 3 ) precipitate size, calculated from the SANS data. Conversely, the UH 3 phase fraction was found to strongly depend on the hydrogen content in the same cast samples. A substantially reduced UH 3 particle size distribution was observed in the rolled uranium relative to cast uranium containing the same nominal hydrogen content. It is hypothesized that the suppression of UH 3 formation in the rolled uranium is driven by increased hydrogen trapping at grain boundaries, and theoretical calculations that account for trap density, potency, and hydrogen diffusion kinetics support this hypothesis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Coupled Small and Wide-Angle X-Ray Scattering Study of Phase Transformation Mechanisms in U-6Wt Pct Nb

The elevated temperature phase transformation kinetics of U-6wt%Nb in both wrought and cast conditions were investigated using in-situ high energy synchrotron X-ray scattering. The evolution of the phase content, γ-phase composition, and microstructure morphology was determined through the analysis of simultaneously collected wide-angle diffraction and small-angle scattering (SAXS) data. The results of the wide-angle scattering analysis, especially the phase fractions and average composition of the γ-phase, provide model parameters to enable a quantitative analysis using the SAXS data. Greater clarity regarding the kinetics of different precipitation mechanisms, namely the continuous precipitation (CP) of α-U within the γ-phase matrix and the discontinuous (DP) grain boundary precipitation of a lamellar microstructure, consisting of α-U and Nb-rich γ-phase are obtained from the coupled measurement modes. These results indicate that the CP mechanism is responsible for the initial precipitation of α-U at all temperatures considered. Near the nose in the time-temperature-transformation (TTT) diagram at ~798 K, both mechanisms are active during the early stages of phase transformation. However, the DP mechanism has an increasingly long incubation period with decreasing temperature below the TTT nose. In conclusion, the average interlamellar spacing obtained from the SAXS analysis increases with time, providing further evidence of the so-called divergent DP behavior previously observed in U-6wt%Nb alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Time resolved in-situ small angle X-ray scattering clarifies the competition between continuous and discontinuous precipitation in U-6wt%Nb

In-situ high energy x-ray scattering experiments enable high temporal resolution investigations of precipitation kinetics; Continuous and discontinuous precipitation are competitive near the TTT nose (~525°C); The incubation time for discontinuous precipitation increases significantly at temperatures below the TTT nose; Additional evidence for the divergent interlamellar spacing was observed at 434°C and 466°C

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation and fracture behavior of a laser powder bed fusion processed stainless steel: In situ synchrotron x-ray computed microtomography study

Tensile plastic deformation and fracture behavior of a laser powder bed fusion processed 316L stainless steel alloy was investigated in situ using high-resolution synchrotron x-ray computed microtomography (sXCT). Three different cases were studied: (1) specimen A1, near full-density with initial porosity of 0.04%, (2) specimen B1, initial lack-of-fusion (LOF) porosity of about 3% with the major axis of defects aligned nearly perpendicular to the tensile loading direction (LD), and (3) specimen B, similar to B1 but with the major axis of LOF defects aligned nearly parallel to LD. The effects of type, density, and orientation of defects in as-printed samples on plastic deformation and failure modes were studied by analyzing sXCT image sequences and quantitative defect properties. Specifically, the evolutions of porosity, size, aspect ratio, and angle of gas pores and LOF defects were characterized as a function of applied strain. Moreover, interactions between as-printed defects and deformation-induced crack propagation were investigated. The tensile behavior of specimen A1 was comparable to that of a commercial wrought plate. Furthermore, the quantitative in-situ sXCT results showed a void-growth phenomenon in A1 but without noticeable coalescence, resulting in a ductile cup-cone failure. Specimen B1 showed damage-driven brittle failure with limited plasticity due to early and rapid propagation of open voids. On the other hand, specimen B, with a similar amount of LOF defects as B1, showed deceivingly strong and ductile tensile behavior similar to A1 without any major crack propagations due to the favorable orientation relationship between LOF defects and the LD.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of defect characteristics on tensile deformation of an additively manufactured stainless steel: Evolutions of texture and intergranular strain

The micromechanics of plastic deformation behavior of a selective laser melt processed austenitic stainless steel were studied by investigating the evolutions of texture and intergranular strain using in situ high-energy synchrotron x-ray diffraction (sXRD). The effects of defect characteristics on tensile behavior were studied using three different samples: a near full-density sample with elliptical closed voids and two samples with lack-of-fusion (LOF) defects tensile loaded either perpendicular or parallel to their major axes. The evolutions of pole figures and inverse pole figures show that the full-density specimen develops a strong (111)/(200) fiber texture along the loading direction. For both LOF specimens, the evolution of texture is qualitatively similar to the full-density counterpart, but the development of the fiber texture was much slower, indicating a limited plasticity at a given macroscopic strain. The intergranular strain evolution in the full-density specimen is similar to that of a wrought 316L stainless steel. Conversely, a significantly different intergranular strain development was observed in a LOF specimen, where tensile strain development was observed in both the axial and transverse directions. Finally, the influence of defect type, density, and orientation on the local stress states in the steel matrix and the evolutions of intergranular strains is discussed.

36 MATERIALS SCIENCE↗