Search NASA⌕ Search

Engineering topics

Garn, Troy

Publications and source records attributed to Garn, Troy.

Purification of Gas and Liquid Streams Using Composite Sorbents Embedded in a Polyacrylonitrile Matrix

As new sorbents are developed for purifying gases or fluids via physisorption and/or chemisorption processes, the push is typically to increase the available specific surface area (SSA) to maximize the available binding sites for capturing various species of interest. One downfall to making a sorbent more porous is that it often leads to a product that is fragile or friable and can be damaged (resulting in unwanted powders), thus imposing process limitations. Techniques can be used to enhance the mechanical integrity of a sorbent including heat treatments or pelletization with extrusion or granulation processes but these can result in collapsed, unavailable pore structures within the sorbent, which leads to decreased diffusivity and eventual reduction of desired capacities of target species. An alternative approach for improving the mechanical integrity of the sorbent is to bind it (or encapsulate it) within a porous matrix that passively holds the sorbent in place. Typically, this approach leads to a decrease in sorption efficiency on the basis of starting sorbent mass, because the active sorbent is diluted by the binding matrix material and the active surfaces of the sorbent are somewhat obscured by the binding matrix, but it comes with the advantage that the active sorbent is held in place and better protected from powderization during operation. One approach to accomplish this is to embed the active sorbent in a macroporous passive polyacrylonitrile (PAN) matrix to create a composite sorbent. When optimized, the PAN matrix is highly porous and allows for gaseous or aqueous media transport through the product providing adequate binding site access between the active sorbent and the species of interest. Including a polymer in the composite sorbent limits the maximum operating temperature above which the composite sorbent incurs loss of structural integrity (e.g., decomposes) and/or reduction in SSA. Composite sorbents have been demonstrated with sulfide aerogels (SnS-PAN) for capturing I2(g), hydrogen mordenite (HZ-PAN) and silver-exchanged mordenite (AgZ-PAN) for capturing Kr and Xe, nano-particle metal oxides (N-CAS) for removing arsenic from water, ammonium molybdophosphate (AMP-PAN) for removing 137Cs from aqueous nuclear waste streams, and the phosphate sponge (TPS) composite, which is being used to remove inorganic and orthophosphates from water treatment processes to mitigate introduction to the environment impeding toxic algae bloom formations. This chapter provides details on production of these materials along with options to optimize of the synthesis process. It also includes experimental techniques to characterize products and assess their performances.

polyacrylonitrile, aerogel, gaseous capture, aqueo↗

Purification of Gas and Liquid Streams Using Composite Sorbents Embedded in a Polyacrylonitrile Matrix

As new sorbents are developed for purifying gases or liquids via physisorption and/or chemisorption processes, the objective is typically to increase the specific surface area (SSA) to maximize the available binding sites for capturing various species of interest. One downfall to making a sorbent more porous is that it often leads to a product that is fragile or friable and can be damaged (resulting in unwanted powders), thus imposing process limitations. Techniques can be used to enhance the mechanical integrity of a sorbent, including heat treatments or pelletization with extrusion or granulation processes, but these can result in collapsed, unavailable pore structures within the sorbent, which decreases the diffusivity and eventually reduces the capacities of target species. An alternative approach for improving the mechanical integrity of the sorbent is to bind it (or encapsulate it) within a porous matrix that passively holds the sorbent in place. Typically, this approach leads to a decrease in sorption efficiency on the basis of starting sorbent mass, because the active sorbent is diluted by the binding matrix material and the active surfaces of the sorbent are somewhat obscured by the binding matrix; however, it comes with the advantage that the active sorbent is held in place and better protected from disintegrating during operation. One approach to securing the active sorbent is to embed it in a macroporous, passive polyacrylonitrile (PAN) matrix to create a composite sorbent. When optimized, the PAN matrix is highly porous and allows for gaseous or aqueous media transport through the product, providing adequate binding site access between the active sorbent and the species of interest. Including a polymer in the composite sorbent limits the maximum operating temperature, above which the composite sorbent incurs loss of structural integrity (e.g., decomposes) and/or reduction in SSA. Composite sorbents have been demonstrated with sulfide aerogels (SnS-PAN) for capturing I2(g), hydrogen mordenite (HZ-PAN) and silver-exchanged mordenite (AgZ-PAN) for capturing Kr and Xe, nanoparticle metal oxides (Nano-Composite Arsenic Sorbent, or N-CAS) for removing arsenic from water, ammonium molybdophosphate (AMP-PAN) for removing cesium-137 (137Cs) from aqueous nuclear waste streams, and The Phosphate Sponge (TPS) composite, which is being used to remove inorganic/ortho-phosphates in water treatment processes to mitigate introduction to the environment, which impedes toxic algae bloom formations. This chapter provides details on production of these materials along with options to optimize the synthesis process. It also includes experimental techniques to characterize products and assess their performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Polyacrylonitrile-Chalcogel Hybrid Sorbents for Radioiodine Capture

Powders of a Sn2S3 chalcogen-based aerogel (chalcogel) were combined with powdered polyacrylonitrile (PAN) in different mass ratios (SnS33, SnS50, and SnS70 in mass% of chalcogel), dissolved into dimethyl sulfoxide, and dropped into deionized water to form pellets of a porous PAN-chalcogel hybrid material. Pellets of these hybrid sorbents, along with pure powdered (SnSp) and granular (SnSg) forms of the chalcogel, were then used to adsorb iodine gas under both concentrated and dilute conditions. Both the SnSp and SnSg chalcogels showed very high maximum iodine loadings at 67.2 and 68.3 mass%. The maximum iodine loadings in the SnS33 and SnS50 were high at 32.8 and 53.5 mass%. In all cases, X-ray diffraction results showed the formation of Sn-I phases of SnI4 and SnI4(S8)2 revealing that the iodine binding in these materials is mainly due to a chemisorption process although some evidence also exists that supports a physisorption process.

chalcogel↗

Development and Testing of an Americium/Lanthanide Separation Flowsheet Using Sodium Bismuthate

The separation of Am from the lanthanides and curium is a key step in proposed advanced fuel cycle scenarios. The partitioning and transmutation of Am is desirable to minimize the long-term heat load of material interred in a future high-level waste repository. A separation process amenable to process scale-up remains elusive. Given only subtle chemistry differences within and between the ions of the trivalent actinide and lanthanide series this separation is challenging ; however, higher oxidation states of americium can be prepared using sodium bismuthate and separated via solvent extraction using diamylamylphosphonate (DAAP) extraction. Among the other trivalent metals only Ce is also oxidized and extracted. Due to the long-term instability of Am(VI) , the loaded organic phase is readily selectively stripped to partition the actinide to a new acidic aqueous phase. Batch extraction distribution ratio measurements were used to design a flowsheet to accomplish this separation. Additionally, crossflow filtration was investigated as a method to filter the bismuthate solids from the feed solution prior to extraction. Results of the filtration studies, flowsheet development work and flowsheet performance testing using a centrifugal contactor are detailed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radioactive Iodine and Krypton Control for Nuclear Fuel Reprocessing Facilities

Nuclear fission results in the production of fission products and activation products, some of which tend to be volatile during used fuel reprocessing. These can evolve in volatile species in the reprocessing facility off-gas streams, depending on the separations and reprocessing technologies that are used. Radionuclides that have been identified as “volatile radionuclides” are noble gases (most notably isotopes of Kr and Xe); 3H; 14C; and 129I. Radionuclides that tend to form volatile species that evolve into reprocessing facility off-gas systems are more challenging to efficiently control compared to radionuclides that tend to stay in solid or liquid phases. Future used fuel reprocessing facilities in the United States can require efficient capture of some volatile radionuclides in their off-gas streams to meet regulatory emission requirements. In aqueous reprocessing, these radionuclides are most commonly expected to evolve into off-gas streams in tritiated water [3H2O (T2O) and 3HHO (THO)], radioactive CO2, noble gases, and gaseous HI, I2, or volatile organic iodides. The fate and speciation of these radionuclides from a non-aqueous fuel reprocessing facility is less well known at this time, but active investigations are in progress. An Off-Gas Sigma Team was formed in late FY 2009 to integrate and coordinate the Fuel Cycle Research and Development (FCR&D) activities directed towards the capture and sequestration of the these volatile radionuclides (Jubin 2012a). The Sigma Team concept was envisioned to bring together multidisciplinary teams from across the DOE complex that would work collaboratively to solve the technical challenges and to develop the scientific basis for the capture and immobilization technologies such that the sum of the efforts was greater than the individual parts. The Laboratories currently participating in this effort are Argonne National Laboratory (ANL), Idaho National Laboratory (INL), Oak Ridge National Laboratory (ORNL), Pacific Northwest National Laboratory (PNNL), and Sandia National Laboratories (SNL). This article focuses on control of volatile radionuclides that evolve during aqueous reprocessing of UNF. In particular, most of the work by the Off-gas Sigma Team has focused on the capture and sequestration of 129I and 85Kr, mainly because, as discussed below, control of 129I can require high efficiencies to meet regulatory requirements, and control of 85Kr using cryogenic processing, which has been the technology demonstrated and used commercially to date, can add considerable cost to a reprocessing facility.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fundamental Drop Dynamics and Mass Transfer Experiments to Support Solvent Extraction Modeling Efforts

In support of the Nuclear Energy Advanced Modeling Simulation Safeguards and Separations (NEAMS SafeSep) program, the Idaho National Laboratory (INL) worked in collaboration with Los Alamos National Laboratory (LANL) to further a modeling effort designed to predict mass transfer behavior for selected metal species between individual dispersed drops and a continuous phase in a two phase liquid-liquid extraction (LLE) system. The purpose of the model is to understand the fundamental processes of mass transfer that occur at the drop interface. This fundamental understanding can be extended to support modeling of larger LLE equipment such as mixer settlers, pulse columns, and centrifugal contactors. The work performed at the INL involved gathering the necessary experimental data to support the modeling effort. A custom experimental apparatus was designed and built for performing drop contact experiments to measure mass transfer coefficients as a function of contact time. A high speed digital camera was used in conjunction with the apparatus to measure size, shape, and velocity of the drops. In addition to drop data, the physical properties of the experimental fluids were measured to be used as input data for the model. Physical properties measurements included density, viscosity, surface tension and interfacial tension. Additionally, self diffusion coefficients for the selected metal species in each experimental solution were measured, and the distribution coefficient for the metal partitioning between phases was determined. At the completion of this work, the INL has determined the mass transfer coefficient and a velocity profile for drops rising by buoyancy through a continuous medium under a specific set of experimental conditions. Additionally, a complete set of experimentally determined fluid properties has been obtained. All data will be provided to LANL to support the modeling effort.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Remote Maintenance Design for Pilot-Scale Centrifugal Contactors

Advanced designs of used nuclear fuel recycling processes and radioactive waste treatment processes are expected to include more ambitious goals for aqueous based separations including; higher separations efficiency, high-level waste minimization, and a greater focus on continuous processes to minimize cost and footprint. Therefore, annular centrifugal contactors are destined to play a more important role for such future processing schemes. Pilot-scale testing will be an integral part of development of many of these processes. An advanced design for remote maintenance of pilot-scale centrifugal contactors has been developed and a prototype module fabricated and tested for a commercially available pilot-scale centrifugal contactor (CINC V-02, 5-cm rotor diameter). Advanced design features include air actuated clamps for holding the motor-rotor assembly in place, an integral electrical connection, upper flange o-rings, a welded bottom plate, a lifting bale, and guide pins. These design features will allow for rapid replacement of the motor rotor assembly, which can be accomplished while maintaining process equilibrium. Hydraulic testing of a three-stage prototype unit was also performed to verify that design changes did not impact performance of the centrifugal contactors. Details of the pilot-scale remote maintenance design, results of testing in a remote mockup test facility, and results of hydraulic testing of the advanced design are provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Plan for Solvent Extraction Data Acquisition to Support Modeling Efforts

This testing will support NEAMS SafeSep Modeling efforts related to droplet simulation in liquid-liquid extraction equipment. Physical characteristic determinations will be completed for the fluids being used in the experiment including viscosity, density, surface tension, distribution coefficients, and diffusion coefficients. Then, experiments will be carried out to provide data for comparison to the simulation’s calculation of mass transfer coefficients. Experiments will be conducted with solutions used in the TRansUranic EXtraction (TRUEX) process extraction section. The TRUEX process was chosen since it is one solvent extraction system currently proposed for the separation of actinides and lanthanides from used nuclear fuel, it is diffusion limited, testing can be performed using non radioactive lanthanides to evaluate mass transfer. The extraction section involves transfer of one or more lanthanide species from an aqueous solution to an organic solvent. Single droplets rising by buoyancy will be studied first. Droplet size and number of species transferred will be varied independently to provide mass transfer coefficients as a function of each variable. An apparatus has been designed specifically for these experiments. In order to get more accurate measurements of droplet size, contact time, time of droplet formation, and possibly droplet breakup and coalescence, a high speed camera will be utilized for these experiments. Other potential experiments include examining the effects of jetted droplets and shear flow on the mass transfer coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗