Search NASA⌕ Search

Engineering topics

Garn, Troy G

Publications and source records attributed to Garn, Troy G.

MRWFD Kr Capture Project

Progress report presentation to DOE program representatives.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Summary of GAIN BWR Off-Gas Study: Effect of Charcoal on Kr and Xe Delay

This is a summary of a more extensive report, written in collaboration with the GE-Hitachi BWR Owner's Group, detailing a study of BWR off-gas treatment. The study determined that aged charcoal continues to be effective for the delay of Kr and Xe through BWR off-gas treatment systems. It demonstrates the over-sized nature of existing charcoal beds, and highlights potential areas of improvement.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Separation of Xenon from Krypton in UNF Reprocessing Off-Gas

Reprocessing of used nuclear fuel (UNF) results emits several volatile radionuclides that must be removed from the bulk off gas prior to release in order to meet U.S. regulatory emission requirements. After other volatile radionuclides have been removed, krypton (Kr) remains, along with associated with xenon (Xe) in the gas stream. The half-life of Xe is short enough that by the time UNF is sufficiently cooled to be reprocessed Xe is no longer a radiological concern and it may be release to atmosphere or collected for other purposes. Kr, however, must be placed in long term storage. In order to ensure the smallest practical volume for long term storage, the Xe, which is nearly ten times the volume of Kr, must be separated from the Kr. Although cryogenic distillation has been used successfully for this purpose, high capital and operational cost, along with safety considerations, made development of gas adsorption processes for separation of Xe and Kr attractive. INL developed an engineered form sorbent consisting of silver mordenite in a polyacrylonitrile matrix (AgZ-PAN) capable of complete separation of Xe from Kr in a single pass, allowing Kr to be captured downstream with no detectable Xe present.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Composite media for fluid stream processing, a method of forming the composite media, and a related method of processing a fluid stream

A composite media including at least one crystalline aluminosilicate material in polyacrylonitrile. A method of forming a composite media is also disclosed. The method comprises dissolving polyacrylonitrile in an organic solvent to form a matrix solution. At least one crystalline aluminosilicate material is combined with the matrix solution to form a composite media solution. The organic solvent present in the composite media solution is diluted. The composite media solution is solidified. In addition, a method of processing a fluid stream is disclosed. The method comprises providing a beads of a composite media comprising at least one crystalline aluminosilicate material dispersed in a polyacrylonitrile matrix. The beads of the composite media are contacted with a fluid stream comprising at least one constituent. The at least one constituent is substantially removed from the fluid stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Centrifugal separator devices, systems and related methods

Centrifugal separator devices, systems and related methods are described. More particularly, fluid transfer connections for a centrifugal separator system having support assemblies with a movable member coupled to a connection tube and coupled to a fixed member, such that the movable member is constrained to movement along a fixed path relative to the fixed member are described. Also, centrifugal separator systems including such fluid transfer connections are described. Additionally, methods of installing, removing and/or replacing centrifugal separators from centrifugal separator systems are described.

47 OTHER INSTRUMENTATION↗

Centrifugal separators and related devices and methods

Centrifugal separators and related methods and devices are described. More particularly, centrifugal separators comprising a first fluid supply fitting configured to deliver fluid into a longitudinal fluid passage of a rotor shaft and a second fluid supply fitting sized and configured to sealingly couple with the first fluid supply fitting are described. Also, centrifugal separator systems comprising a manifold having a drain fitting and a cleaning fluid supply fitting are described, wherein the manifold is coupled to a movable member of a support assembly. Additionally, methods of cleaning centrifugal separators are described.

47 OTHER INSTRUMENTATION↗

A Centrifugal Contactor Design to Facilitate Remote Replacement

Advanced designs of nuclear fuel recycling and radioactive waste treatment plants are expected to include more ambitious goals for solvent extraction based separations including; higher separations efficiency, high-level waste minimization, and a greater focus on continuous processes to minimize cost and footprint. Therefore, Annular Centrifugal Contactors (ACCs) are destined to play a more important role for such future processing schemes. This work continues the development of remote designs for ACCs that can process the large throughputs needed for future nuclear fuel recycling and radioactive waste treatment plants. A three stage, 12.5 cm diameter rotor module has been constructed and is being evaluated for use in highly radioactive environments. This prototype assembly employs three standard CINC V-05 clean-in-place (CIP) units modified for remote service and replacement via new methods of connection for solution inlets, outlets, drain and CIP. Hydraulic testing and functional checks were successfully conducted and then the prototype was evaluated for remote handling and maintenance. Removal and replacement of the center position V-05R contactor in the three stage assembly was demonstrated using an overhead rail mounted PaR manipulator. Initial evaluation indicates a viable new design for interconnecting and cleaning individual stages while retaining the benefits of commercially reliable ACC equipment. Replacement of a single stage via remote manipulators and tools is estimated to take about 30 minutes, perhaps fast enough to support a contactor change without loss of process equilibrium. The design presented in this work is scalable to commercial ACC models from V-05 to V-20 with total throughput rates ranging from 20 to 650 liters per minute.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thirty Stage Annular Centrifugal Contactor Thermal Profile Measurements

A thirty stage 5 cm annular centrifugal contactor cascade has been assembled and tested to obtain thermal profiles during both ambient and heated input conditions of operation. Thermocouples were installed on every stage as well as feed inputs and Real-time data was taken during experiments lasting from two to eight hours at total flow rates of 0.5 to 1.4 liters per minute. Ambient temperature profile results show that only a small amount of heat is generated by the mechanical energy of the contactors. Steady state temperature profiles mimic the ambient temperature of the lab but are higher toward the middle of the cascade. Heated inlet solutions gave temperature profiles with smaller temperature gradients, more driven by the temperature of the inlet solutions than ambient lab temperature. Temperature effects of solution mixing, even at rotor speeds of 4000 rpm, were not measurable.

42 ENGINEERING↗

Pilot-Scale TRUEX Flowsheet Testing for Separation of Actinides and Lanthanides from Used Nuclear Fuel

Advanced aqueous separation processes are being developed for the recycling of used nuclear fuel as part of the U.S. Department of Energy Nuclear Energy Advanced Fuel Cycle Initiative. The Transuranic Extraction (TRUEX) Process is being developed as part of these advanced separations processes for the separation of actinides and lanthanides from the used nuclear fuel. Testing of a TRUEX flowsheet has been performed using a thirty stage, 5-cm centrifugal contactor pilot plant. This testing was performed using a non-radioactive feed surrogate and data were collected and analyzed to evaluate removal efficiencies of the lanthanides, mass transfer efficiency of the lanthanides in the extraction and strip sections of the flowsheet, and the temperature profile of the process solutions throughout the centrifugal contactor pilot plant. Results indicate >99.9% separation for all lanthanides and mass transfer efficiencies typically ranging from 85% to 100%. Solution temperatures for each contactor stage, as well as general process performance, are also described.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of a New Remote Handling Design for High Throughput Annular Centrifugal Contactors

Advanced designs of nuclear fuel recycling plants are expected to include more ambitious goals for aqueous based separations including; higher separations efficiency, high-level waste minimization, and a greater focus on continuous processes to minimize cost and footprint. Therefore, Annular Centrifugal Contactors (ACCs) are destined to play a more important role for such future processing schemes. Previous efforts defined and characterized the performance of commercial 5 cm and 12.5 cm single-stage ACCs in a “cold” environment. The next logical step, the design and evaluation of remote capable pilot scale ACCs in a “hot” or radioactive environment was reported earlier. This report includes the development of remote designs for ACCs that can process the large throughput rates needed in future nuclear fuel recycling plants. Novel designs were developed for the remote interconnection of contactor units, clean-in-place and drain connections, and a new solids removal collection chamber. A three stage, 12.5 cm diameter rotor module has been constructed and evaluated for operational function and remote handling in highly radioactive environments. This design is scalable to commercial CINC ACC models from V-05 to V-20 with total throughput rates ranging from 20 to 650 liters per minute. The V-05R three stage prototype was manufactured by the commercial vendor for ACCs in the U.S., CINC mfg. It employs three standard V-05 clean-in-place (CIP) units modified for remote service and replacement via new methods of connection for solution inlets, outlets, drain and CIP. Hydraulic testing and functional checks were successfully conducted and then the prototype was evaluated for remote handling and maintenance suitability. Removal and replacement of the center position V-05R ACC unit in the three stage prototype was demonstrated using an overhead rail mounted PaR manipulator. This evaluation confirmed the efficacy of this innovative design for interconnecting and cleaning individual stages while retaining the benefits of commercially reliable ACC equipment for remote applications in the nuclear industry. Minor modifications and suggestions for improved manual remote servicing by the remote handling specialists were provided but successful removal and replacement was demonstrated in the first prototype.

99 GENERAL AND MISCELLANEOUS↗

Temperature control in a 30 stage, 5-cm Centrifugal Contactor Pilot Plant

Temperature profile testing was performed using a 30 stage 5-cm centrifugal contactor pilot plant. These tests were performed to evaluate the ability to control process temperature by adjusting feed solution temperatures. This would eliminate the need for complex jacketed heat exchanger installation on the centrifugal contactors. Thermocouples were installed on the inlet and outlets of each stage, as well as directly in the mixing zone of several of the contactor stages. Lamp oil, a commercially available alkane mixture of C14 to C18 chains, and tap water adjusted to pH 2 with nitric acid were the solution feeds for the temperature profile testing. Temperature data profiles for an array of total throughputs and contactor rpm values for both single-phase and two-phase systems were collected with selected profiles. The total throughput ranged from 0.5-1.4 L/min with rotor speeds from 3500-4000 rpm. Inlet solution temperatures ranging from ambient up to 50 °C were tested. Results of the two-phase temperature profile testing are detailed

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗