Search NASA⌕ Search

Engineering topics

Garn, Troy G.

Publications and source records attributed to Garn, Troy G..

At least 19 records

Krypton Concentration using HZ-PAN

Idaho National Laboratory (INL) has developed and tested engineered sorbents to separate and capture volatile fission products such iodine, xenon (Xe), and krypton (Kr) from off-gas streams. As noble gases, Xe and Kr can be difficult to capture and separate. Historically, cryogenic distillation has been used to execute the separation. However, performing this separation from bulk air streams is expensive and can pose significant hazards. INL has successfully developed two different sorbents for Xe and Kr capture, silver mordenite polyacrylonitrile and hydrogen mordenite polyacrylonitrile (HZ-PAN). Adsorption studies to date successfully separated and captured Kr from carrier gas streams, but those studies focused primarily on initial separation and capture. Successful utilization in a used nuclear fuel (UNF) reprocessing facility, however, requires further concentration of the Kr to minimize long term storage volumes. This study focuses on the concentration of Kr utilizing HZ PAN as the concentrating media. Concentrating Kr during desorption is ideal for two reasons: one, to produce Kr that can be used for commercial and research applications, or two, to minimize the volume of the radioactive gaseous waste stream for disposal. This report investigates the Kr concentrating potential of HZ-PAN by running multiple Kr adsorption-desorption cycles, collecting the desorbed effluent from a saturated HZ-PAN column, and loading it onto a fresh column. This study demonstrates that four adsorption-desorption cycles can transform a 150 ppmv Kr stream into a 37.5% Kr stream, an overall concentration factor of 2497. Each concentration step results in successively smaller volumes desorbed, reducing volume by a factor of approximately 40,000. Depending on the operational goals, during desorption one could collect smaller volume fractions of high concentration Kr (~ 67%). This demonstration should be considered proof-of-concept. Further refinement is necessary to develop optimum operating schemes to integrate into UNF off-gas treatment.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗

Effects of HZ-PAN Sorbent Irradiation on Kr Adsorption

Idaho National Laboratory (INL) has developed and studied an engineered form hydrogen mordenite in polyacrylonitrile matrix (HZ-PAN) for krypton (Kr) adsorption. Adsorption studies to date have successfully separated and captured Kr from carrier gas streams, but those studies have used non-radioactive gases for testing. However, if utilized in a used nuclear fuel (UNF) reprocessing facility, this sorbent will be exposed to the potential deleterious effects of radiation. This report explores Kr adsorption behavior on HZ PAN after the sorbent was exposed to gamma radiation. A batch of HZ-PAN was divided into five segments, a control segment that was not exposed to radiation, and the other four segments that were exposed to progressively increased levels of radiation dose, up to 5 MGy. Samples were then analyzed to determine total surface area as well as their capacity to capture Kr. This study reveals HZ PAN retains its initial surface area and Kr-capture capacity after radiation exposure, indicating viability for service in radioactive gases.

42 - ENGINEERING↗

Evaluation of Engineered Form MOFs CaSDB and HKUST-1

Idaho National Laboratory (INL) and Pacific Northwest National Laboratory (PNNL) have studied different sorbents for the purpose of separating krypton (Kr) and xenon (Xe). PNNL has researched various metal-organic frameworks (MOFs) that have characteristics theoretically suitable for the separation. Based on computational analysis, PNNL chose Calcium–4,4’–sulfonyl dibenzoate (CaSDB) and Hong Kong University of Science and Technology MOF1 (HKUST–1). The raw MOFs are supplied in a powder form and must be incorporated into a robust engineered form to be viable for gas separation. In 2016, PNNL produced an engineered form of CaSDB by compressing and grinding the raw MOF material. This form was sent to INL for adsorption testing. Gentle mechanical agitation of the compressed form produced a large amount of powder, resulting in the conclusion that the form was not viable for the application. In 2019, INL successfully produced two engineered forms, CaSDB–EF1 and HKUST–EF2, by incorporating the active MOF powders into a polyacrylonitrile (PAN) binder. PNNL also produced two engineered forms, CaSDB–10pmma and HKUST–10pmma, by using polymethyl methacrylate (PMMA) as a binder. Surface area analysis indicated that the forms could be viable for separations in which the CaSDB–EF1 retained 84% of the raw CaSDB surface area and CaSDB–10pmma retained 48%. HKUST–EF2 retained all the raw HKUST–1 surface area, whereas HKUST–10pmma retained only 28%. Mechanical stability testing demonstrated that the PMMA forms formed a fine powder whereas, the PAN forms did not. In general, adsorption testing showed that CaSDB–10pmma had a lower Xe breakthrough capacity than CaSDB–EF1, but a higher saturation capacity at both room temperature and at 253 K. The CaSDB MOF was intended to be used as a room temperature sorbent to capture Xe. However, both CaSDB engineered forms displayed relatively short initial break through times. Reduced temperature increased the Xe capacity of both engineered forms. HKUST–1 was expected to be effective only at sub-zero temperatures. At 195 K, HKUST–10pmma had an initial Xe breakthrough capacity of 119 mmol/ kg, compared to HKUST–EF2 at 339 mmol/ kg. The saturation capacities were 275 and 383 mmol/ kg, respectively. HKUST–10ppm also had a lower Kr capacity of 1.7 mmol/kg, whereas the HKUST–EF had a Kr capacity of 3 mmol/ kg. Test results indicate that the PAN engineered forms are a more suitable choice for the complete separation of Xe and Kr, due to the increase in initial breakthrough capacity. CaSDB allows rapid breakthrough of Kr and Xe regardless of the type of engineered form. At 253 K, it is more viable, but is still not the most effective sorbent. HKUST–EF2 demonstrated viability for Xe capture at 195 K, which may merit further study, however it may be cost prohibitive.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transition group metals for the capture of radioactive xenon

A xenon capture system that reduces the concentration of xenon in a carrier gas is disclosed. An example xenon capture system includes a carrier gas with a first concentration of xenon that flows through an intake into a chamber. Within the chamber is a reaction area that has at least one peripheral sidewall. The reaction area operates at a predetermined temperature, flow rate, and low pressure. Within the reaction area is at least one xenon capture mechanism that is at least partially formed of a transition metal. When the carrier gas is exposed to the xenon capture mechanism, the xenon capture mechanism adsorbs xenon from the carrier gas. The carrier gas, with a second concentration of xenon, exits the chamber through the exhaust outlet.

42 ENGINEERING↗

Evaluation of an Engineered Form MOF CaSDB

Under the Off-Gas Sigma Team, Idaho National Laboratory (INL) and Pacific Northwest National Laboratoory (PNNL) have been able to study various sorbents for the separation of krypton (Kr) and xenon (Xe). PNNL has researched and prepared various metal-organic frameworks (MOFs) to use for the separation. Calcium–4,4’–sulfonyl dibenzoate (CaSDB), a high surface area MOF, was synthesized and sent to INL for deep bed testing. The MOF showed an acceptable saturation capacity, but a low breakthrough capacity; However, the recieved MOF was deemed as unusable in a flow system because of its powdery nature. In 2018, PNNL sent a sample of CaSDB – MOF powder to INL with the goal to incorporate it into an engineered form that maintained adsorption properties comparable to the original MOF. It was anticipated that the engineered form of the sorbent would possess sufficient mechanical strength to be used in a column, and eliminate the dustiness of the raw material to improve handling and operability. An engineered from of CaSDB – MOF (CaSDB – EF1) was produced by incorporating the raw powder into a polyacrylonitrile (PAN) binder. The PAN binding material eliminated the dustiness of the raw MOF and provided a robust matrix that prevents damage from handling and use in a column. Xe adsorption testing of the sorbent revealed that it performs as well or better than previous CaSDB samples tested at INL, with an initial breakthrough capacity of 14.4 mmol/ kg at ambient temperature. Reducing the operating temperature to 253 K resulted in an increased breakthrough capacity of Xe.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Developing an Engineered Form of MOFs CaSDB and HKUST –1

Selective Kr and Xe capture to various adsorbents have been studied extensively as part of the Off-gas Sigma Team. In hopes to develop a better adsorbent, Pacific Northwest Nation Laboratory (PNNL) has suggested the use of metal-organic frameworks (MOFs). In 2016, PNNL developed compressed and ground engineered forms of calcium–4,4’–sulfonyl dibenzoate (CaSDB) MOF which was tested at Idaho National Laboratory (INL). The tests found that the CaSDB had a sufficient saturation capacity, but a low breakthrough capacity. The larger issue was that the CaSDB form was not robust enough to withstand handling necessary for installation in a column and flow system. In 2018, PNNL sent two MOFs, CaSDB and Hong Kong University of Science and Technology – 1 (HKUST–1), to INL. INL’s goal was to develop an engineered form that maintained adsorption properties comparable to the original MOFs and was robust enough to use in a column. Initial testing consisted of batch-wise contacts of the MOFs with aprotic solvents and water, to ensure there was not a dramatic degradation of the material. BET analyses confirmed that the MOFs could be exposed to water and DMSO without significant loses in surface area. MOF engineered forms were successfully produced, CaSDB–EF1 and HKUST–EF2, using the INL-patented PAN technique (USA Patent No. 8,686,083, 2013). Brunauer, Emmet and Teller (BET) analyses performed on the engineered forms yielded surface areas of 148 m 2 /g and 1487 m 2 /g for CaSDB–EF1 and HKUST–EF2 respectively, 67.6% and 83.7% of the surface areas of the respective pristine materials. Both engineered form MOFs are deemed acceptable for further study to determine efficacy for selective Kr and Xe capture.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

HZ-PAN and AgZ-PAN Desorption Characterization

While previous research focused on adsorption of Kr and Xe on HZ-PAN and AgZ-PAN, recent focus has shifted to desorption. Preliminary testing was completed last year, providing valuable information to guild further research. Preliminary studies indicated that thermal swing operations, along with a sweep gas, are required for effective desorption from both AgZ-PAN and HZ-PAN. This series of tests focused on characterizing the bulk gases removed from each sorbent and relative separation of Kr and Xe from each other and from the bulk air. Single stage adsorption/ resulted in 99-100% separation of Xe from Kr, and 77-83% separation of Kr from air while concentrating Xe seven to tenfold and Kr three to fivefold when Xe is not present. Previous isothermal studies of both sorbents have shown that sorbent capacity is proportional to feed gas concentration. Therefore, it is anticipated that additional HZ-PAN stages will further concentrate and purify the final Kr stream with higher efficiency. It is expected that Xe will be released to atmosphere after desorption. However, it could also be purified further with more AgZ-PAN stages. Further testing should be done to determine maximum purity achievable for both Kr and Xe. Additionally, renewed focus on increasing Xe capacity on AgZ-PAN and Kr capacity on HZ-PAN is recommended.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cycle Testing of AgZ-PAN and HZ-PAN

Idaho National Laboratory (INL) has been conducting, as part of the off-Gas Sigma Team, producing and testing sorbents for the selective capture of xenon and krypton from surrogate nuclear fuel recycling off-gas streams. AgZ-PAN and HZ-PAN, both developed and produced at INL, have shown promising results for the selective capture and separation of xenon and krypton, respectively. Previous testing of both sorbents has focused on saturation and initial breakthrough capacities across a variety of operating conditions. However, the sorbents can only be truly viable for use in a process if they have sufficient longevity through multiple adsorption/desorption cycles. This research, therefore, focused on putting both sorbents through as many thermal swing adsorption/desorption cycles as possible over the course of one year. The primary focus of cycling tests was on AgZ-PAN, which previously demonstrated possible loss of capacity after multiple cycles. While capacity was shown to be recoverable over the short term, the goal is to ensure effective long-term viability so it was placed through 100 cycles, the estimated equivalent of one year of operation. HZ-PAN had not shown any deleterious effects from cycling during previous testing. Additionally, due to the colder temperatures required for Kr capture, each cycle required considerably more time to complete, so this sorbent was subjected to 50 cycles. Both sorbents maintained their capacities throughout the series, indicating promising potential for long-term reliability.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Initial Evaluation of CaSDB MOF Xe and Kr Capacities

Idaho National Laboratory (INL) and Pacific Northwest National Laboratory (PNNL) have been conducting parallel research, as part of the off-Gas Sigma Team, producing and testing sorbents for the selective capture of xenon and krypton from surrogate nuclear fuel reprocessing off-gas streams. Sorbents promising on a laboratory scale are tested further at INL in a system designed to emulate anticipated plant process conditions. This report summarizes INL’s initial testing of CaSDB MOF developed and produced at PNNL. Previous testing of the same base CaSDB MOF material, conducted at INL in 2016, indicated good saturation capacity for xenon, but a low xenon capacity at initial breakthrough. Additionally, the material displayed a propensity to break down into fine powder during use and handling. The current test series looks at the same base material, but with refinements to production and activation techniques. A series of ambient temperature tests were conducted to determine capacities of CaSDB MOF for krypton and xenon at initial breakthrough as well as at saturation. Adsorption tests were run in triplicate at superficial velocities of 21 and 53 cm/min, along with a single test at 373 cm/min. Saturation capacity across all tests was 30 mmol/kg +/- 2, with capacity at initial breakthrough of 8 mmol/kg +/- 1. It should be noted that while the usable portion of the material has a much tighter size distribution than that previously tested, propensity to physically break down into very fine powder with use and handling continues to be problematic. An improved engineered form is recommended prior to further testing

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary Desorption studies for HZ-PAN and AgZ-PAN

Adsorption of Kr and Xe on HZ-PAN and AgZ-PAN has been the studied extensively. Prior research focused on sorbent capacity and breakthrough of Kr and Xe, with desorption cycles completed in order to close material balances and prepare sorbents for further adsorption testing. This series of tests was designed to determine preliminary information about desorption to guide further research to optimize desorption cycles for each sorbent. A series of desorption tests were run using thermal and pressure swing operations. For AgZ-PAN, these tests indicated that both heat and carrier gas are likely necessary to removed adsorbed gases. However, vacuum pressure and heat may be sufficient to desorb gases from HZ-PAN, which should result in a cleaner Kr stream during desorption. Desorption optimization for both sorbents merits further study in order to make final waste form volume as small as possible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multi-Column Kr/Xe Separation Testing at Representative Superficial Velocities with DGOSPREY Model Validation

Previous testing of AgZ-PAN and HZ-PAN for the separation and removal of xenon and krypton from air have been promising. This report details the results of multi-column testing at superficial velocities chosen to emulate probably velocities in a full-scale used nuclear fuel reprocessing facility. Additionally, results were used to validate the DG-OSPREY model under development at Georgia Institute of Technology.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and evaluation of a silver mordenite composite sorbent for the partitioning of xenon from krypton in gas compositions

A new engineered form composite sorbent for the selective separation of xenon from krypton in simulant composition off-gas streams resulting from the reprocessing of used nuclear fuel has been developed and evaluated. A sodium mordenite powder was incorporated into a macroporous polymer binder, formed into spherical beads and successfully converted to a 9 wt.% silver form composite sorbent. The final engineered form sorbent retained the characteristic surface area indicative of sodium mordenite powder. The sorbent was evaluated for xenon adsorption potential with capacities measured as high as 30 millimoles of xenon per kilogram of sorbent achieved at ambient temperature and 460 millimoles of xenon per kilogram sorbent at 220 K. Xenon/krypton selectivity was calculated to be 22.4 with a 1020 µL/L xenon, 150 µL/L krypton in a balance of air feed gas at 220 K. Furthermore, adsorption/desorption thermal cycling effects were evaluated with results indicating sorbent performance was not significantly impacted while undergoing numerous adsorption/desorption thermal cycles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multi-component testing using HZ-PAN and AgZ-PAN Sorbents for OSPREY Model validation

In efforts to further develop the capability of the Off-gas SeParation and RecoverY (OSPREY) model, multi-component tests were completed using both HZ-PAN and AgZ-PAN sorbents. The primary purpose of this effort was to obtain multi-component xenon and krypton capacities for comparison to future OSPREY predicted multi-component capacities using previously acquired Langmuir equilibrium parameters determined from single component isotherms. Experimental capacities were determined for each sorbent using two feed gas compositions of 1000 ppmv xenon and 150 ppmv krypton in either a helium or air balance. Test temperatures were consistently held at 220 K and the gas flowrate was 50 sccm. Capacities were calculated from breakthrough curves using TableCurve® 2D software by Jandel Scientific. The HZ-PAN sorbent was tested in the custom designed cryostat while the AgZ-PAN was tested in a newly installed cooling apparatus. Previous modeling validation efforts indicated the OSPREY model can be used to effectively predict single component xenon and krypton capacities for both engineered form sorbents. Results indicated good agreement with the experimental and predicted capacity values for both krypton and xenon on the sorbents. Overall, the model predicted slightly elevated capacities for both gases which can be partially attributed to the estimation of the parameters and the uncertainty associated with the experimental measurements. Currently, OSPREY is configured such that one species adsorbs and one does not (i.e. krypton in helium). Modification of OSPREY code is currently being performed to incorporate multiple adsorbing species and non-ideal interactions of gas phase species with the sorbent and adsorbed phases. Once these modifications are complete, the sorbent capacities determined in the present work will be used to validate OSPREY multicomponent adsorption predictions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The solvent extraction of Am(VI) using centrifugal contactors

One of the major challenges in nuclear fuel cycle research is the development of a separation that can be deployed on a process scale for americium from the lanthanides. Unlike most lanthanides, americium can be oxidized to higher oxidation states, and this presents an opportunity to exploit high valent americium for such a separation. Strong oxidizing agents are required. However, the preparation of hexavalent americium using sodium bismuthate has now become routine in our laboratory. The success of separations based on oxidized americium depends on not only the yield of the higher oxidation state, but also its persistence in solution. In batch contact work, short contact times allowed for the extraction of Am(VI) with DAm ~ 4, using 1 M diamylamylphosphonate as the ligand. Based on bench-scale extraction and stripping studies a flowsheet was designed and a hot test was performed in a radiological fume hood using three CINC, 5-cm centrifugal contactors. Stage 1 was the americium extraction stage. In stage 2, americium stripping was attempted after reduction with a low concentration of hydrogen peroxide. As the only lanthanide that oxidizies and extracts in this flowsheet, it was attempted to reduce and strip cerium in the third stage contactor. The results of this hot test are compared with batch extraction studies, where it was found that americium extraction was comparable to batch contacts, while stripping was less efficient than expected. Proposals for the next test are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Closed Fuel Cycle Waste Treatment Strategy

This study is aimed at evaluating the existing waste management approaches for nuclear fuel cycle facilities in comparison to the objectives of implementing an advanced fuel cycle in the U.S. under current legal, regulatory, and logistical constructs. The study begins with the Global Nuclear Energy Partnership (GNEP) Integrated Waste Management Strategy (IWMS) as a general strategy and associated Waste Treatment Baseline Study (WTBS). The tenets of the IWMS are equally valid to the current waste management study. However, the flowsheet details have changed significantly from those considered under GNEP. In addition, significant additional waste management technology development has occurred since the GNEP waste management studies were performed. This study updates the information found in the WTBS, summarizes the results of more recent technology development efforts, and describes waste management approaches as they apply to both a nominal case study and near-term target reprocessing flowsheets. Many of the waste management technologies discussed also apply to other potential flowsheets that involve reprocessing. The report summarizes the waste arising from aqueous reprocessing of a typical light-water reactor (LWR) fuel to separate actinides for use in fabricating metal sodium fast reactor (SFR) fuel and from electrochemical reprocessing of the metal SFR fuel to separate actinides for recycle back into the SFR in the form of metal fuel. The primary streams considered and the recommended waste forms include: • Tritium separated from either a low volume gas stream or a high volume water stream. The recommended waste form is low-water cement in high integrity containers (HICs). • Iodine-129 separated from off-gas streams in aqueous processing. There are a range of potentially suitable waste forms. As a reference case, a glass composite material (GCM) formed by the encapsulation of the silver Mordenite (AgZ) getter material in a low-temperature glass is assumed. A number of alternatives with distinct advantages are also considered including a fused silica waste form with encapsulated nano-sized AgI crystals. • Carbon-14 separated from LWR fuel treatment off-gases and immobilized as a CaCO3 in a cement waste form. • Krypton-85 separated from LWR and SFR fuel treatment off-gases and stored as a compressed gas. • An aqueous reprocessing high-level waste (HLW) raffinate waste which is immobilized by the vitrification process in one of three forms: a single phase borosilicate glass, a borosilicate based glass ceramic, or a multi-phased crystalline synthetic rock (Synroc). • An undissolved solids (UDS) fraction from aqueous reprocessing of LWR fuel that is either included in the borosilicate HLW glass or is immobilized in the form of a metal alloy in the case of glass ceramics or Synroc. • Zirconium-based LWR fuel cladding hulls and stainless steel (SS) fuel assembly hardware that are washed and super-compacted for disposal or as an alternative with high promise the purification and reuse (or disposal as low-level waste, LLW) of Zr by reactive gas separations. • Electrochemical process salt HLW which is incorporated into a glass bonded Sodalite waste form known as the ceramic waste form (CWF). • Electrochemical process UDS and SS cladding hulls which are melted into an iron based alloy waste form. Mass and volume estimates for each of the recommended waste forms based on the source terms from the reference mass balances are reported. In addition to the above listed primary waste streams, a range of secondary process wastes are generated by aqueous reprocessing of LWR fuel, metal SFR fuel fabrication, and electrochemical reprocessing of SFR fuel. These secondary wastes have been summarized and volumes estimated by type and classification. The important waste management data gaps and research needs have been summarized for each primary waste stream and selected waste process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and design of a multi-column experimental setup for Kr/Xe separation

As a precursor to FY-15 Kr/Xe separation testing, design modifications to an existing experimental setup are warranted. The modifications would allow for multi-column testing to facilitate a Xe separation followed by a Kr separation using engineered form sorbents prepared using an INL patented process. A new cooling apparatus capable of achieving test temperatures to -40° C and able to house a newly designed Xe column was acquired. Modifications to the existing setup are being installed to allow for multi-column testing and gas constituent analyses using evacuated sample bombs. The new modifications will allow for independent temperature control for each column enabling a plethora of test conditions to be implemented. Sample analyses will be used to evaluate the Xe/Kr selectivity of the AgZ-PAN sorbent and determine the Kr purity of the effluent stream following Kr capture using the HZ-PAN sorbent.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Adsorption Isotherms for Xenon and Krypton using INL HZ-PAN and AgZ-PAN Sorbents

The generation of adsorption isotherms compliments the scale-up of off-gas processes used to control the emission of encapsulated radioactive volatile fission and activation products released during Used Nuclear Fuel (UNF) reprocessing activities. A series of experiments were conducted to obtain capacity results for varying Kr and Xe gas concentrations using HZ-PAN and AgZ-PAN engineered form sorbents. Gas compositions for Kr ranged from 150-40,000 ppmv and 250-5020 ppmv for Xe in a helium balance. The experiments were all performed at 220 K at a flowrate of 50 sccm. Acquired capacities were then respectively fit to the Langmuir equation using the Langmuir linear regression method to obtain the equilibrium parameters Qmax and Keq. Generated experimental adsorption isotherms were then plotted with the Langmuir predicted isotherms to illustrate agreement between the two. The Langmuir parameters were provided for input into the OSPREY model to predict breakthrough of single component adsorption of Kr and Xe on HZ-PAN and AgZ-PAN sorbents at the experimental conditions tested. Kr and Xe capacities resulting from model breakthrough predictions were then compared to experimental capacities for model validation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Polyacrylonitrile-Chalcogel Hybrid Sorbents for Radioiodine Capture

Powders of a Sn2S3 chalcogen-based aerogel (chalcogel) were combined with powdered polyacrylonitrile (PAN) in different mass ratios (SnS33, SnS50, and SnS70 in mass% of chalcogel), dissolved into dimethyl sulfoxide, and dropped into deionized water to form pellets of a porous PAN-chalcogel hybrid material. Pellets of these hybrid sorbents, along with pure powdered (SnSp) and granular (SnSg) forms of the chalcogel, were then used to adsorb iodine gas under both concentrated and dilute conditions. Both the SnSp and SnSg chalcogels showed very high maximum iodine loadings at 67.2 and 68.3 mass%. The maximum iodine loadings in the SnS33 and SnS50 were high at 32.8 and 53.5 mass%. In all cases, X-ray diffraction results showed the formation of Sn-I phases of SnI4 and SnI4(S8)2 revealing that the iodine binding in these materials is mainly due to a chemisorption process although some evidence also exists that supports a physisorption process.

chalcogel↗